Pro-Ject Audio System X2B Turntable Instruction Manual

June 9, 2024
Pro-Ject Audio System

X2B
INSTRUCTIONS FOR USEPro Ject Audio System X2B Turntable
-

X2B Turntable

Pro Ject Audio System X2B Turntable - fig 1

Controls, features and connections

  1. MAIN PLATTER
  2. CHASSIS
  3. SPEED CONTROL
  4. MOTOR WITH MOTOR PULLEY
  5. DRIVE BELT
  6. SUB-PLATTER
  7. TONEARM FLANGE
  8. TONEARM COUNTERWEIGHT
  9. TONEARM LIFT
  10. TONEARM REST AND REMOVABLE TRANSPORT LOCK
  11. CARBON / ALUMINIUM TONEARM TUBE
  12. HEADSHELL WITH FINGER LIFT
  13. ANTI-SKATING WEIGHT WITH THREAD
  14. ANTI-SKATING WEIGHT SUPPORT
  15. ANTI-SKATING STUB WITH ANTI-SKATING ADJUSTMENT SCALE
  16. LID HINGE
  17. HINGE FASTENERS
  18. LID
  19. PHONO OUTPUT SOCKET WITH MINI XLR AND RCA OUTPUT
  20. POWER SUPPLY SOCKET
  21. MAIN POWER BUTTON

Turntable accessories

  1. Instruction for use
  2. Cartridge alignment protractor
  3. Anti-skating weight
  4. Allen key 1.5mm
  5. Allen key 2mm
  6. Allen key 3mm
  7. Counterweight no. 31 for cartridges with weight between 7 – 12g
  8. Single adaptor
  9. Connect IT E RCA 1,23m
  10. Power supply
  11. Round drive belt for 78 r.p.m.
  12. White cotton gloves

Dear music lover,
Thank you for purchasing a Pro-Ject Audio Systems record player.
In order to achieve maximum performance and reliability, please study these instructions carefully.
Warning of a hazard for the user, the unit or possible misuse
Important notice
The following instructions for adjusting the cartridge are provided in case the cartridge is replaced by a different model at a later date.
During assembling and adjustment small parts could be lost if they are not carefully placed in a suitable receptacle. Before starting assembly make yourself acquainted with the parts listed above which are correspondingly numbered in the technical drawings above.

Safety instructions

The power supply is used to connect and disconnect the unit from the mains. Make sure that the plug is easily accessible at all times. Hold the plug when unplugging the power cord. Never handle the power cord while your hands are wet or damp.
Avoid letting liquids enter the device. Never place any item containing liquid, like a flower vase, on or near the device. Never spill any liquid on the device. Never place any naked flame sources, like lighted candles, on or near the device. The product shall not be used in damp or wet locations, next to a bathtub, sink, swimming pool or any other similar conditions.
Keep plastic bags away from children to prevent any risk of suffocation.
The turntable was shipped partially disassembled in order to avoid damage to sensitive parts.
Please check immediately to make sure that neither the packaging nor the device was damaged in transit.

SETUP AND INSTALLATION

  1. PLATTER AND DRIVE BELT ASSEMBLY
    Install the drive belt (5) and the main platter (1) as shown in following ilustration.Pro Ject Audio System X2B Turntable - DRIVE BELT
ASSEMBLY

  2. MOUNTING AND CONNECTING THE CARTRIDGE
    All cartridges with half inch mounting holes can be mounted. Leave the needle’s protection cover on, fit the cartridge to the headshell by using the supplied screws by passing one screw through each slot in the headshell (12). Do not tighten the nuts yet.
    Connect the tonearm wires with the cartridge pins as follows:white| left channel positive (L+)
    ---|---
    red| right channel positive (R+)
    green| right channel return (R-)
    blue| left channel return (L-)

The full sound quality of the record player can only be achieved if the cartridge is adjusted correctly. Particular tools like the Pro-Ject Audio Systems alignment tool are required to accomplish this job properly. If you are not well acquainted with the adjustment of cartridges, please call for the willing help of your Pro-Ject Audio Systems dealer.
Please note: adjusting a cartridge and tonearm calls for the greatest care in order to avoid damaging the cartridge or tonearm bearings. Ask your local dealer for help if you are unsure in any of the necessary steps and precautions which must be taken.

  1. CARTRIDGE DOWNFORCE ADJUSTMENT
    The counterweight (8) supplied is suitable for cartridges weighing between 7 – 12g (counterweight no. 31).
    Adjust the downforce prior to setting the anti-skating force.
    Place counterweight (8) halfway along the counterweight support rod at rear of arm, so that the downforce scale shows towards the front of the player. Lower the armlift and position the cartridge in the space between arm rest and platter. Carefully rotate the counterweight (8) until the armtube balances out. The arm should return to the balanced position if it is moved up or down. This adjustment must be done carefully. Do not forget to remove the cartridge protection cap if fitted.
    Once the arm is correctly balanced return it to the rest. Hold the counterweight (8) without moving it, and gently revolve the downforce scale ring until the zero is in line with the anti-skating prong. Check whether the arm still balances out.
    Rotate the counterweight counter clockwise (seen from the front) to adjust the downforce according to the cartridge manufacturer’s recommendations.
    The recommended downforce for the factory fitted cartridge is 18mN.

  2. ANTI-SKATING FORCE ADJUSTMENT
    Unpack (14) ANTI-SKATING STUB WITH ANTI-SKATING ADJUSTMENT SCALE and screw it into the predrilled hole (see image down below). Unpack (13) ANTI-SKATING WEIGHT WITH THREAD and put the antiskating thread hook over the correct groove for your cartridge’s downforce on the anti-skating adjustment scale.
    The anti-skating force must be adjusted corresponding to the downforce as follows:

 Downforce
10 – 14mN
15 – 19mN
20mN and bigger| Groove in the stub (15)
1st from bearing rings
2nd   ”         ”         ”
3rd    ”         ”         “
---|---

Pro Ject Audio System X2B Turntable - drilled hole
here

  1. CONNECTION TO THE AMPLIFIER
    The record player offers gold plated female RCA phono sockets and a mini XLR output for the connection to your amplifier.
    To use our True Balanced Connection, your Pro-Ject turntable needs to be equipped with an MC cartridge!
    RCA OUTPUT:
    Use the supplied Connect it E Phono cable and connect it to a Phono input (sometimes labelled gram, disc or RIAA) on your amplifier. Make sure that the phono input offers correct matching and amplification for the type of cartridge used. Line inputs (like CD, Tuner, Tape or Video) are not suitable.
    Take care about connecting the left and right channel correctly. The RIGHT CHANNEL is usually marked RED, the LEFT CHANNEL BLACK or WHITE. Check the manual of your amplifier for relevant information. An earthing wire may be connected to the screw terminal between the sockets if you encounter humming problems.
    If your amplifier does not have an input suitable for phono cartridges, a separate phono amplifier stage for MM or MC cartridges is required. It has to be connected between record player and a free line level input of the amplifier.
    MINI XLR OUTPUT:
    To use the mini XLR output & take full advantage of the true balanced connection your turntable needs to be equipped with an MC cartridge. „True Balanced Connection“ phono cables are available separately. You can find more details on our website or ask your Pro-Ject dealer for information.Pro Ject
Audio System X2B Turntable - MINI XLR OUTPUTFor detailed product information regarding Pro-Ject Audio Systems interconnect cables and phono amplifiers please visit our website: www .project-audio.com

  2. MAINS POWER CONNECTION
    The turntable is supplied with a power supply suitable for your country’s mains supply. Check the label before connecting to ensure compliance with the mains rating in your house.
    Connect the low voltage plug from the power supply to the socket (20) on the rear of the record player before connecting the power supply to the mains.

  3. FITTING THE LID
    Fit the lid (dust cover 18) carefully over the hinge prongs and adjust the screws (17) until the lid stays open where you want it to without being too stiff to open or close.

  4. SWITCHING ON AND OFF
    Press the main power button (21) to start the turntable.

  5. CHANGING REPLAY SPEED
    To play records at 33 r.p.m. press the speed control button (3). Pressing the speed control button one more time selects 45 r.p.m. The selected speed is shown respectively by the flashing LED. When the platter has attained full speed, the LEDs stop flashing.
    To be able to play 78 r.p.m. the flat drive belt has to be removed and the round drive belt has to be fitted around the sub-platter (6) and the larger diameter part of the motor pulley (4). To do so the main platter (1) has to be removed.
    After the round drive belt has been fitted, pressing the speed control button two times selects 78 r.p.m..
    When full speed is attained the LED 45 stops flashing.

  6. ADJUSTING THE VERTICAL TRACKING ANGLE (VTA)
    Put a record on the platter. When the needle is lowered into the record groove and the tonearm is not resting on the lift arm, the tube of the tonearm should be parallel to the surface of the record.
    If it is not, loosen both hexagon screws in the tonearm base just enough to allow vertical movement of the arm pillar without force and slide the arm up or down until it is parallel.
    Retighten the hexagon screws without applying excessive force (which would deform the arm pillar) – finger tight is quite sufficient.Pro Ject Audio
System X2B Turntable - TRACKING ANGLE

  7. ADJUSTING THE AZIMUTH
    The cartridge needle must be vertical in the record groove in order to trace the groove wall modulations correctly.
    A small screw at the bearing end of the arm allows incorrect azimuth to be corrected.
    Slacken off the screw just enough to be able to revolve the arm tube without applying force.
    Note! Do not remove this screw completely!Pro Ject Audio System X2B
Turntable - screw completely

  8. USEFUL TIPS
    The lid is not only a dust cover but also a resonant structure likely to be excited by and to pass into the plinth the acoustic energy emanating from your loudspeakers during replay. Therefore, it is recommended to remove the lid for achieving a better sound quality. The record player should be positioned on a lowresonance surface, like wood or multiple layer ply board to avoid structural vibrations disturbing replay.

  9. MAINTENANCE AND CLEANING
    Your record player requires little or no regular maintenance. Remove dust with a slightly moistened antistatic cloth. Never use a dry cloth because this will create static electricity which attracts even more dust! Antistatic cleaning fluids are available at specialized stores but must be applied sparingly to avoid damage to rubber parts. It is recommended to fit the needle cover before cleaning or maintenance to avoid damage. If the player is not used over a long period of time, the drive belt should be removed to prevent unequal stretching.

Always disconnect the record player from the mains power supply as a precaution before maintenance!

TECHNICAL SPECIFICATIONS

Pro-Ject 9’’ Carbon/Alu sandwich tonearm

Nominal speeds 33/45/78 r.p.m.
Speed variance 33: ±0.25 %   45: ±0.20 %
Wow and flutter 33: ±0.12 %   45: ±0.10 %
Signal to noise -70dB
Effective tonearm mass 13.5g
Effective tonearm length 9 ” (230mm)
Overhang 18mm
Power consumption 5W/ 0.3W standby mode
Outboard power supply 15V/ 0.8 A DC, universal power supply
Dimensions (W x H x D) 460 x 150 x 340mm, dust cover open 460 x 415 x 435mm
Weight 10 kg

Potential incorrect use and fault conditions
Pro-Ject turntables are manufactured to the highest standards and undergo strict quality controls before leaving the factory. Faults that may possibly occur are not necessarily due to material or production faults but can sometimes be caused by incorrect use or unfortunate circumstances. Therefore, the following list of common fault symptoms is included.
The platter doesn’t turn although the unit is switched on:
The unit is not connected to the mains power supply.
No mains at the socket.
Drive belt is not fitted or has slipped off.
No signal through one or other channel or both channels:
No signal contact from the cartridge to the internal tonearm wiring or from that to the arm lead or from that to the phono box or between that and the amplifier. This could be due to a faulty plug, broken wire or solder joint or simply loose plug/socket connection.
Phono input not selected at amplifier.
Amplifier is not switched on.
Amplifier or speakers are defective or muted.
No connection to the loudspeakers.
Strong hum on phono input:
No earth connection from cartridge or arm or arm cable to amplifier, or earth loop.
Distorted or inconsistent sound from one or both channels:
Record player is connected to wrong input of amplifier, or MM/MC switch incorrectly set.
Needle or cantilever damaged.
Wrong r.p.m., drive belt overstretched or dirty, platter bearing without oil, dirty or damaged.

Service
Should you encounter a problem which you are not able to alleviate or identify despite the above information, please contact your dealer for further advice. Only when the problem cannot be resolved there should the unit be sent to the responsible distributor in your country.
Guarantee repairs will only be affected if the unit is returned correctly packaged. For this reason we recommend keeping the original packaging.
Never return a record player without making sure that is it safely disassembled and correctly packaged in the original packaging according to the diagrams on the last page of this user guide. Please remove these parts and pack them separately: lid, counterweight, anti-skating weight, platter and belt. Fit the cartridge protection cap.
Insert the transport lock for the tonearm prior to carefully packaging the record player.

Warranty

The manufacturer accepts no responsibility for damage caused by not adhering to these instructions for use and/or by transportation without the original packaging. Modification or change to any part of the product by unauthorized persons, release the manufacturer from any liability over and above the lawful rights of the customer.

Pro-Ject Audio Systems is a Registered Trademark of H. Lichtenegger.
This guide was produced by: Pro-Ject Audio Systems
Copyright© 2023. All rights reserved.

The information was correct at the time of going to press.
The manufacturer reserves the right to make changes to the technical specification without prior notice as deemed necessary to uphold the ongoing process of technical development.Pro Ject Audio System X2B Turntable - Audio
Systems

Getting started:

  • Make sure to have enough space to unpack your turntable.
  • Always unpack and set up in a clean environment.
  • Please Do NOT throw away the packaging! If you need service or want to return your product, please send it in the original packaging including all inserts. In case of damage due to alternative packaging your dealer cannot guarantee a full refund.
  • complete manual: www.project-audio.com/en/product/x2-b

Pro Ject Audio System X2B Turntable - unpack your
turntable

1. Unpack all items from accessory bag:
a) Felt mat
(33/45 RPM) & round belt (78 RPM)
c) Adapter for 7“ singles / Allen key
d) Connect it Phono E cable
e) Gloves
f) Anti Skating Weight| 2. Remove dust cover carton from the box.
---|---
Pro Ject Audio System X2B Turntable - 1| Pro Ject
Audio System X2B Turntable - 2
3. Lift the wrapped turntable out of the box.| 4. Carefully remove the covering.
Pro Ject Audio System X2B Turntable - 3| Pro Ject
Audio System X2B Turntable - 4
5.Unpack the platter.| 6. Unpack the counterweight and power supply from the buttom inserts.
Pro Ject Audio System X2B Turntable - 5| Pro Ject
Audio System X2B Turntable - 6
7. Put the flat drive belt (b) on the pulley and sub-platter.| 8. Put the platter on the turntable.
Pro Ject Audio System X2B Turntable - 7| Pro Ject
Audio System X2B Turntable - 8
9. The turntable should always be placed on a flat surface. Check with a spirit level*.| 10. If necessary, level the turntable by adjusting the feet.
Pro Ject Audio System X2B Turntable - 9| Pro Ject
Audio System X2B Turntable - 10
11. Remove tonearm twist tie.| 12. Put the counterweight in place.
Pro Ject Audio System X2B Turntable - 11| Pro
Ject Audio System X2B Turntable - 12
13. Remove the stylus protection cover.| 14. Put a record on the platter.
Pro Ject Audio System X2B Turntable - 13| Pro
Ject Audio System X2B Turntable - 14
15. Carefully place the tonearm between platter and armrest and lower the tonearm lift.| 16. Balance the tonearm by turning the counter-weight forwards and backwards on the rod.
Pro Ject Audio System X2B Turntable - 15| Pro
Ject Audio System X2B Turntable - 16
17. Hold the counterweight and set the dial to ‘V by ONLY turning the dial to the marker.| 18. Turn the WHOLE counterweight counterclockwise until the scale reads 23.
Pro Ject Audio System X2B Turntable - 17| Pro
Ject Audio System X2B Turntable - 18
19. Put the loop of the Antiskating weight (f) in the outer groove.| 20. Plug in power supply and Connect it E (d)’. ir Yellow cable marks to the amplifier.
Pro Ject Audio System X2B Turntable - 19| Pro
Ject Audio System X2B Turntable - 20
21. Unpack dust cover and install it.| 22. Turn the motor on/off [under the chassis] Select your playback speed with the selector.
Pro Ject Audio System X2B Turntable - 21| Pro
Ject Audio System X2B Turntable - 22
23. Connect to your hifi-system and have fun with music!| Pro Ject Audio
System X2B Turntable - 23

Unleash the full potential with a True Balanced Connection!

Pro Ject Audio System X2B Turntable - 24

True Balanced Connection
Balanced audio connections are usually known from the professional sector like recording studios or live concerts. It is very important to have a stable & interference free connection, as these signals, especially microphone signales, will be highly amplified. The same applies to the connection from your turntable to the phono preamplifier. The big advantage of a balanced connection is its ability to remove picked up noise and interferences.
Balanced connections use three wires for one channel: ground, a hot and a cold wire.
The cold wire carries the inverted (reversed in polarity) hot signal. At the receiving end the cold signal is flipped and added together. The trick happens here: If the cable picks up any noise, the noise is added to both signals.
So, a positive interference is a positive tick on the hot and on the cold signal. If you now flip one of them, the interference is also inverted, so you get the same interference once in a positive and once in a negative direction. If you now add these two signals, the noise will cancel out.
To take full advantage of the true balanced connection your turntable should be equipped with an MC cartridge.

Pro Ject Audio System X2B Turntable - 01Pro Ject
Audio System X2B Turntable - 25

Need help?
Feel free to contact us. We have experienced partners all over the world. Find your dealer here: www.project-audio.com/en/find-a-dealer/

Service
Should you encounter a problem which you are not able to alleviate or identify despite the above information, please contact your dealer for further advice. Only when the problem cannot be resolved there should the unit be sent to the responsible distributor in your country.
Warranty repairs will only be affected if the unit is returned correctly packaged. For this reason we recommend keeping the original packaging.
Never return a record player without making sure that is it safely disassembled and correctly packaged in the original packaging according to the diagrams on the last page of this user guide. Please remove these parts and pack them separately: lid, counterweight, anti-skating weight and belt.
Fit the cartridge protection cap and the transport lock for the tonearm tube, prior to carefully packaging the record player.

Warranty
The manufacturer accepts no responsibility for damage caused by not adhering to these instructions for use and/or by transportation without the original packaging. Modification or change to any part of the product by unauthorized persons, release the manufacturer from any liability over and above the lawful rights of the customer.

Warranty: Terms and Conditions

  • A warranty is valid only for products purchased from an authorized Pro-Ject Audio Systems retailer or dealer.
  • This warranty offer is limited to the repair of the equipment (which could be a repair or replacement at our discretion, neither of which affects your original warranty).
  • Neither transportation or any other costs, nor any risk for removal, transportation and installation of products is covered by this warranty.
  • A warranty is only valid for the original owner. It is not transferable.
  • To validate your warranty, you will need to provide the original sales invoice or other proof of ownership and date of purchase.
  • Warranty must be claimed within two years of purchase from an authorized dealer. After this period of time, the warranty will expire.
  • The legal warranty obligation exists in addition to this warranty and is not limited by this warranty.

A Pro-Ject Audio Systems warranty relates to claims of defects in materials and/or workmanship at the time of purchase. It does not cover:

  • Deterioration of component parts, the nature of which is to become worn or depleted with use, such as batteries and headphone ear pads, drive belts and cartridges.
  • Damages caused by incorrect installation, connection or packing.
  • Damages caused by any use other than the correct use described in the user manual, negligence, modifications, or use of parts that are not made or authorized by Pro-Ject Audio Systems.
  • Damages caused by faulty or unsuitable ancillary equipment.
  • Damages caused by accidents, lightning, water, fire heat, war, public disturbances or any other cause beyond the reasonable control of Pro-Ject Audio Systems and its appointed distributors.
  • Products where the serial number has been altered, deleted, removed or made illegible.
  • Repairs or modifications that have been executed by an unauthorized person.

Commercial Use
Faults caused due to using domestic products in commercial environments or on commercial scales are not covered by warranty. This turntable is intended for domestic use only. Using them for business applications are done so at your own risk.
Pro-Ject Audio Systems is a Registered Trademark of H. Lichtenegger.
This guide was produced by: Pro-Ject Audio Systems
Copyright © 2022. All rights reserved.

The information, pictures and figures were correct at the time of going to press. The manufacturer reserves the right to make changes to the technical specification without prior notice as deemed necessary to uphold the ongoing process of technical development.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals