saxby Tango Post IP44 9 2w Warm White Instruction Manual
- June 12, 2024
- saxby
Table of Contents
Saxby Tango Post IP44 9 2w Warm White
Product Information
The Tango Post (13922) is a lighting product manufactured by two companies:
BH17 7BY in the UK and Brilliant AG located at Brilliantstrasse 1, D-27442
Gnarrenburg in the EU. The product consists of the following components:
- Cable wired to product
- Terminal block case
- EARTH wire
- NEUTRAL wires
- LIVE wires
- EARTH wire
- Supply cable
- Spacing strip
The product is designed and manufactured for lighting purposes and is compliant with safety regulations.
Product Usage Instructions
- Ensure that the power supply is turned off before installing or handling the product.
- Identify the cable wired to the product and separate it from other cables.
- Remove the terminal block case cover to access the internal wiring.
- Connect the EARTH wire to the appropriate grounding point following local electrical codes and regulations.
- Connect the NEUTRAL wires to the corresponding terminals, ensuring a secure and proper connection.
- Connect the LIVE wires to their respective terminals, ensuring correct polarity.
- Double-check all connections for any loose or exposed wires.
- Securely attach the EARTH wire using appropriate fasteners or clips.
- Replace the terminal block case cover.
- If necessary, use the supplied spacing strip to maintain proper spacing between wires and other components.
- Once the installation is complete, turn on the power supply to activate the product.
- Refer to the product manual for any additional instructions or troubleshooting information.
For further assistance or inquiries, visit the official website at www.saxbylighting.com.
Safety Warnings
- This is a Class 1 product and must be earthed.
- This unit should be fitted by a competent and qualified electrician.
- Install in accordance with IEE Wiring regulations and current Building Regulations.
- To prevent electrocution switch off at mains supply before installing or maintaining this fitting. Ensure other persons cannot restore the electrical supply without your knowledge.
- If you are in any doubt, please consult a qualified electrician.
- This light fitting should be connected to a circuit with a 30mA CD fitted.
- Always use the correct type and wattage bulb. Never exceed the wattage stated.
- This product is not suitable for dimming.
- Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist.
- Check with your local authority or retailer for recycling advice.
- This product is rated at IP44.
- This product is not suitable for locations in or near a marine or sea environment.
- This product should be installed onto a solid surface (such as concrete or paving slabs), and not on soil.
Care Information
Allow 10 minutes to cool before replacing, adjusting or cleaning. Do not use abrasive cleaners as these could damage the finish. While stainless steel is very resistant to corrosion, maintenance is required to preserve its high- quality appearance. Wash the product with warm soapy water, removing all surface deposits. Rinse with clear water and wipe dry with a soft cloth. Surface corrosion may arise after installation. This is normally caused by tiny iron particles left behind after the brushing process when finishing. Wash and dry as detailed above, then wipe all over with a soft cloth soaked with a protective oil.
- In extreme environmental conditions such as marine locations, industrial pollution, or acid rain, these maintenance procedures should be carried out four times a year.
- For severe corrosion, non-abrasive cream cleaners or proprietary stainless steel cleaners should be used to remove the corrosion, then rinse and protect as detailed above.
- Do not clean the units with a pressure washer.
Assembly/ User Instructions
Before you start
Please read these instructions carefully before fitting and retain them for
reference. Check the packaging and make sure that you have all the required
parts. Follow each assembly step in order to prevent incorrect assembly.
Ensure that the product is fully assembled as illustrated before use. The
Light pack contains:
Light fitting
Terminal connection block(s). Fixing pack. The following tools may be required
Selection of cross and hat head screwdrivers Electric drill and assorted drill
bits. Wire strippers.
Electrical insulation tape
These assembly diagrams are intended as a guide – if in doubt consult a
qualified electrician. Plan the desired layout of this fitting carefully,
ensuring the cables will reach the distance between the junction box and the
light fitting. Avoid locating any cables in positions that would cause a
hazard. Position cables and outdoor rated junction boxes (not supplied away
from areas where they may be at risk of being cut, trapped, or damaged We
recommend that you use H05RN-F specification cable (not supplied) which is an
outdoor grade, rubber-sheathed cable. The main supply cable must have a
minimum cross-sectional area of 1.0mm cables muscle protected using durable
consult or last funkine Existing fittings must be completely removed before
installation of a new product. Before removing the existing fitting, carefully
note the position of each set of wires.
- Usino base plate as a lemolate. mark my no holes onto the son mount surface. Drill holes to the necessary size and depth – taking care not to damage any concealed pipes or wiring below the mounting surface.
- We recommend fitting this product with fixings (A & B) which are suitable for use on most solid surfaces. however alternative fixings may be required.
- Having correctly identified the wiring from your existing light fitting, pull the wire through the hole and connect it to the connection block inside the product in the following way:
- Pull terminal block (D) from the inside of the tube.
- Unscrew the 4 screws which attach the black box to the spacing strip. Open the black box and pull out the terminal block, then wire as shown in the diagram.
- Check that you have correctly identified the supply wires. the connections are tight and no loose strands have been left out of the connection block.
- Push the terminal block back into the black box, and refit the terminal block cover.
- Push the terminal block up into the tube.
- Locate the product in position and fit the screws to secure it in
- Replace the fuse or circuit breaker and switch it on. Your light is now ready or use
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>