saxby 99816 Reeve 2 Daylight Instruction Manual

Saxby 99816 Reeve 2 Daylight

Product Information

• Supply Voltage: 220-240 V~, 50 Hz
• Bulb:
  • Type: 99816—18W LED module (SMD), 6500K
  • Type: 99817—33W LED module (SMD), 6500K
• Energy efficiency class: E
• Non-replaceable light source
• Non-replaceable control gear
• Conformity with all relevant UKCA Directive requirements
• Conformity with all relevant EC Directive requirements
• The power supply is double-insulated and does not require connection to an earth circuit
• IP65 rated
• IK08 rated

Product Usage Instructions
Warning:
Existing fittings must be completely removed before installing the new product. Carefully note the position of each set of wires before removing the existing fitting. Switch off the power supply at the fuse board. Seal the screws and cable entry points to
maintain the IP rating of the product.

Installation
Determine the position of your light fitting, considering the cable entry position. Ensure there is sufficient cable coming out of the wall to connect to the terminal block. Mount the light fitting on a solid surface like a brick or block wall, making sure there are no other cables or pipes beneath the surface. An approved outdoor-rated plug and socket or an approved outdoor- rated external terminal block may be required.

Wiring
If not fitting to a plug, the product must be wired to an IP68 outdoor- rated terminal block. We recommend using items 90131/90132 (outdoor rated terminal block). Connect the wiring from your existing light fitting to the approved outdoor rated or approved double insulated terminal block (not supplied) in the following way:

Secure the connection block with two layers of insulation tape.

Care and Safety
Clean the light fitting with a soft dry cloth. Do not use solvents or abrasive cleaners as they may damage the finish. Always switch off the power supply before cleaning. The LED module is protected by a shade, which cannot be replaced. If the shade
becomes cracked or damaged, the light fitting must be discarded.

Disposal
Do not dispose of waste electrical products with household waste. Please recycle where facilities exist. Check with your Local Authority or local store for recycling advice.

Dimming
This product is not suitable for dimming.

Instruction Manual
Reeve 2 – 99816, 99817 For further information, please visit https://www .lighting-info.co.uk/99816

Manufacturer
Manufacturer: BH17 7BY EU Manufacturer: Brilliant AG, Brilliantstrasse 1, D-27442 Gnarrenburg Website: www.saxbylighting.comThank you for purchasing this light fitting. Please read the instructions carefully before use to ensure safe and satisfactory operation of this product. Retain these instructions for future reference.

Thank you for purchasing this light fitting. Please read the instruction carefully before use to ensure the safe and satisfactory operation of this product. Please retain these instructions for future reference.

Warning
This light fitting is Double Insulated and does not require connection to an Earth circuit.

• Please read these instructions carefully before commencing any work.
• This unit must be fitted by a competent and qualified electrician.
• Install in accordance with the IEE Wiring regulations and current Building Regulations.
• Check the pack and make sure you have all the parts listed.
• To prevent electrocution switch off the mains supply before installing or maintaining this fitting. Ensure other persons cannot restore the electrical supply without your knowledge.
• If you are in any doubt, please consult a qualified electrician.
• This light fitting should be connected to a circuit with a 30mA RCD fitted.
• If replacing an existing fitting, make a careful note of the connections.
• This system contains non-replaceable parts and cannot be serviced. If damage occurs the part should be scrapped.
• Take care not to drill into any pipes or main cables beneath the surface during mounting hole preparation.
• The entire unit gets hot whilst on for a period of time.
• Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your local authority or retailer for recycling advice.

Layout

Plan the desired layout of this fitting carefully, ensuring the cables will reach the distance between the junction box and the light fitting. Avoid locating any cables in positions that would cause a hazard. Position cables and junction boxes (not supplied)
away from areas where they may be at risk of being cut, trapped, or damaged. We recommend that you use H05RN-F specification cable (not supplied) which is an outdoor grade, rubber-sheathed cable. The main supply cable must have a minimum cross-section area of 1.0mm2. Cables must be protected using suitable conduit or plastic trunking. The products should not be fitted to PIR circuits or short-duration timed switches.

Installation

Existing fittings must be completely removed before the installation of a new product. Before removing the existing fitting, carefully note the position of each set of wires. Note that the power needs to be isolated/switched off at the fuse board. Ensure that the screws and cable entry points are sealed to maintain the IP rating of the product. Determine the position of your light fitting taking into account the entry position of the cable and make sure there is sufficient cable coming out of the wall to connect to the terminal block. Ensure that the mounting surface is solid, preferably a brick or block wall, and ensure that there are no other cables or pipes beneath the surface. An approved outdoor-rated plug and socket may be required. Alternatively, an approved outdoor-rated external terminal block may be used. We recommend item 90131/90132 (outdoor rated terminal block).

• Refer to the diagram below. Decide on the location of the product. Measure the distance between the mounting bracket location slots, and mark the location of the fixing holes on the mounting surface.
• Drill holes and fit-supplied wall plugs (suitable for masonry only – for other surfaces use appropriate fixings). Fix mounting brackets in place.
• Wire as detailed Wiring diagram.
• Attach the product to mounting brackets by pushing until securely held.
• Replace the fuse or circuit breaker and switch it on. Your light is now ready for use.

Wiring
If not fitting to a plug then the product must be wired to an IP68 outdoor- rated terminal block. We recommend item 90131/ 90132 (outdoor rated terminal block). Having correctly identified the wiring from your existing light fitting, connect to the approved outdoor rated or approved double insulated terminal block (not supplied) in the following way:

Check that…

• You have correctly identified the wires.
• The connections are tight.
• No loose strands have been left out of the connection block.
• When completed, ensure that there are no bare or loose strands of wire exposed, and cover all exposed areas of the connection block with 2 layers of insulation tape.

Technical data

Care and Safety

We recommend cleaning with a soft dry cloth. Do not use solvents or abrasive cleaners as these could damage the finish. For your safety, always switch off the power supply before cleaning. The LED module is protected by a shade. The shade cannot be replaced, if the shade becomes cracked or damaged, this light fitting must be discarded.

V1 05/11/2021
UK Manufacturer: BH17 7BY
EU Manufacturer: Brilliant AG, Brilliantstrasse 1, D-27442 Gnarrenburg

References

• Saxby Lighting - Commercial and Domestic Lighting Supplier
• Directory Contents

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>