Saxby 92273 Stratus Recessed Panel Light Instruction Manual

June 12, 2024
saxby

Instruction manual
STRATUS PRO
92273, 92274, 92543

Saxby 92273 Stratus Recessed Panel Light

Thank you for purchasing this light fitting. Please read the instruction carefully before use to ensure safe and satisfactory operation of this product. Please retain these instruction for future reference.

Warning

Icon This light fitting is double insulated and does not require connection to an Earth circuit.
Please read these instructions carefully before commencing any work This unit must be fitted by a competent and qualified electrician.
Install in accordance with the IEE Wiring regulations and current Building Regulations. Check the pack and make sure you have all the parts listed.
To prevent electrocution switch off at the mains supply before installing or maintaining this fitting. Ensure other persons cannot restore the electrical supply without your knowledge.
This light fitting should be connected to a fused circuit.
If replacing an existing fitting, make a careful note of the connections.
The part of the panel light at Safety Extra Low Voltage (33-40V DC ) via a transformer. Never connect the light fittings directly to the mains without using a transformer.
This system contains non-replaceable parts and cannot be serviced. If damage occurs the part should be scrapped.
Dimmable only when used in conjunction with suitable dimmable drivers.
Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your local authority or retailer for recycling advice.

Layout

Plan the desired layout of these fittings carefully, ensuring the cables will reach the distances between the LED Driver and each light fitting.
Ensure the there is adequate ventilation for the LED Driver.
Avoid locating any cables in positions that would cause a hazard. Position cables and junction boxes (not supplied) away from areas where they may be at risk from being cut, trapped or damaged.
The mains supply cable must have a minimum cross section area of 1.0mm.
Cables must be protected using suitable conduit or plastic trunking2.
These fittings are designed to be fitted into a suspended ceiling.
Panels are rated as TPA according to Building Regulations B2.

Installation

Existing fittings must be completely removed before installation of a new product. Before removing the existing fitting, carefully note the position of each set of wires.
Note that the switch is turned off before installation.
For 92543, this product is colur changing and can be either warm white (3000K) or cool white (4000K) or daylight white (6000K). Choose your preferred colour before installing by using the inline switch.

  • If there is a ceiling tile in position then ensure that it is removed (See Fig. 1).
  • Wire LED driver as shown below and connect driver cable to panel using push & twist connector (See Fig. 2)
  • Place panel fitting into the ceiling. Ensure that the fitting is sitting properly on the T bar of the suspended ceiling and is not fouling any of the supporting bars (See Fig. 3).

Saxby 92273 Stratus Recessed Panel Light - Fig 1

Wiring
Having correctly identified the wiring from your existing light fitting, pull the mains wire through the hole and connect to the connection block inside the LED driver in the following way:
This unit is double insulated and must not be earthed. If there are any incoming earth cables, they must be joined together and well insulated with good quality insulation tape. This is to ensure earth continuity throughout your property.

Saxby 92273 Stratus Recessed Panel Light - Fig 2

Check that…
You have correctly identified the wires.
The connections are tight.
No loose strands have been left out of the connection block.

Commissionig
Ensure that the product is sitting properly on the suspended ceiling frame (see Fig. 4). Replace any other ceiling tiles.
Replace fuse or circuit breaker and switch on. Your light is now ready for use.

Technical data

Supply Voltage:| 220-240 V~, 50 Hz| Operational Voltage:   33-40V DC
---|---|---
Bulb Type:| 92273: 40W LED (SMD), 4000K| This product contains a light source of energy efficiency class E.
92274: 40W LED (SMD), 6000K| This product contains a light source of energy efficiency class E.
92543: 40W LED (SMD) CCT, 3000K/4000K/6000K| This product contains a light source of energy efficiency class E.
| Non-replaceable light source
---|---
| Replaceable control gear by a professional
| Conformity with all relevant UKCA Directive requirements.
| Conformity with all relevant EC Directive requirements.
Icon| The power supply is double insulated and does not require connection to an earth circuit.
| The part of panel light is Class III product – designed to be supplied via a transformer.
****| Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or local store for recycling advice.
| This product is not suitable for dimming.
| It is rated at IP40 for 92273, 92274.
| It is rated at IP44 for 92543.

Accessories available

Surface mount kit – 81850
This kit will allow the panels to be mounted to the ceiling when not being used in a suspended ceiling.

Suspension kit – 81744
This kit will allow the panels to be suspended up to 1 metre from the ceiling.

Recess clip – 91237
One set recess clip (4pcs) required for recessed mount on alternative ceilings. Installation details please refer to the instruction manual of Recess Clip.

Care and Safety

We recommend cleaning with a soft dry cloth. Do not use solvents or abrasive cleaners as these could damage the finish.
For your safety, always switch off the power supply before cleaning.
For further information, please visit https://www.lighting-info.co.uk/92273

V6 10/03/2023
UK Manufacturer: BH17 7BY
EU Manufacturer: Brilliant AG,
Brilliantstrasse 1, D-27442 Gnarrenburg
www.saxbylighting.com

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

saxby User Manuals

Related Manuals