RAB XDIM Phase Dimmer Instructions
- June 12, 2024
- RAB
Table of Contents
RAB XDIM Phase Dimmer
Product Information
The Phase Dimmer, model XDIM, is an electrical device used to control the brightness of compatible dimmable LED, CFL, incandescent, or halogen products. It is designed to be installed in accordance with electrical code and regulations to prevent the risk of fire and electrical shock. The dimmer should be used together with an air-break switch and powered off at the fuse box before installation.
It is important to note that the Phase Dimmer should not be used to control receptacles, motor-operated appliances, or transformer-supplied appliances to avoid overheating and possible damage to the equipment.
When connecting multiple products with a single dimmer, it is recommended to use the same type of dimmable LED, CFL, or incandescent products to enhance dimmer performance.
Product Usage Instructions
Step 1: Before installation, turn off the power at the fuse box or circuit breaker.
Step 2: Follow the provided instructions to install the Phase Dimmer, ensuring it is connected with an air-break switch.
Step 3: Set the minimum brightness level of the dimmer to make bulbs turn on immediately and maximize the dimming range.
Step 4: If you have any doubts or questions regarding the instructions, consult a licensed electrician.
Step 5: Switch to the leading mode when using inductive loads.
Step 6: Ensure that the product is only used with compatible dimmable LED, CFL, incandescent, or halogen products. Do not mix different product types when connecting multiple products to a single dimmer.
Step 7: To enter programming mode, press and hold the On/Up and Off/Down paddles for 3 seconds until the indicator light flashes.
Using the Paddles:
- On/Up Paddle:
- Turn light on: When the light is off, short press the On/Up Paddle once.
- Continuously increase brightness: When the light is on, short press the On/Up Paddle, the brightness increases until it reaches 100%.
- Gradually increase brightness: When the light is on, press and hold the On/Up Paddle, the brightness will gradually increase until it reaches the minimum level or until the On/Up Paddle is released.
- Quickly adjust brightness: When the light is on or off, press the On/Up Paddle twice consecutively.
- Off/Down Paddle:
- Turn light off: When the light is on, short press the Off/Down Paddle once.
- Quickly adjust to the lowest dim level: When the light is on or off, press the Off/Down Paddle twice consecutively.
- Gradually decrease brightness: When the light is on, press and hold the Off/Down Paddle, the brightness will gradually decrease until it reaches the minimum level or until the Off/Down Paddle is released.
Note: The Phase Dimmer complies with Part 15 of the FCC Rules and operates without causing harmful interference. It also accepts any interference received, including interference that may cause undesired operation.
WHAT’S IN THE BOX
TOOLS NEEDED
- 5mm Philips Screwdriver
- Electrical Tape
- Electrician Knife
- Test Pencil
- Pliers
- Ruler
INSTRUCTIONS
Phase Dimmer
RAB Lighting is committed to creating high-quality, affordable, well-designed and energy-efficient LED lighting and controls that make it easy for electricians to install and end users to save energy. We’d love to hear your comments. Please call the Marketing Department at 888-RAB-1000 or email: marketing@rablighting.com
BASIC OPERATION
- Short Press: Within 0.5 seconds
- Long Press: Over 0.5 seconds
- Double Press: Within 1 second
Power Indicator
- White light constant brightness: Power-on stage
On/Up Paddle
- Turn light on: When the light is off, short press the On/Up Paddle once
- Continuously increase brightness: When the light is on, short press the On/Up Paddle, the brightness increases until the brightness reaches 100%
- Gradually increase brightness: When the light is on, press and hold the On/Up Paddle, the brightness will gradually increase until the brightness reaches the minimum level or until the On/Up is released
- Quickly adjust brightness: When the light is on or off, press the On/Up Paddle for 2 consecutive times
Off/Down Paddle
- Turn light off: When the light is on, short press the Off/Down Paddle once
- Quickly adjust to the lowest dim level: When the light is on or off, press the Off/Down Paddle 2 times
- Gradually decrease brightness: When the light is on, press and hold the Off/Down Paddle, the brightness will gradually decrease until the brightness reaches the minimum level or until the Off/Down Paddle is released
Programming Mode
- To enter programming mode, press and hold the On/Up and Off/Down paddle for 3 seconds until the indicator light flashes.
- To set the minimum brightness/low-end trim, press the On/Up Paddle to turn on the lights and adjust to the desired minimum brightness. Short press the Off/Down Paddle 3 times to set.
- To exit programming mode, press and hold the On/Up and Off/Down Paddle for 3 seconds. The dimmer will automatically exit programming mode after 1 minute without operation.
Switch
- F: Forward Phase Control (leading edge control mode)
- A: Auto detect control mode
- R: Reverse Phase Control (training edge control mode)
Note: after dip switch adjustment, please power off and then power on again.
Power Cut Off Switch
- Push in to connect to line voltage
- Pull out to disconnect line voltage
Brightness Indicator
| No. | Brightness Level | Brightness Indicator |
|---|---|---|
| 1 | Brightness Level 10 | LED 2~LED 11 |
| 2 | Brightness Level 9 | LED 2~LED 10 |
| 3 | Brightness Level 8 | LED 2~LED 9 |
| 4 | Brightness Level 7 | LED 2~LED 8 |
| 5 | Brightness Level 6 | LED 2~LED 7 |
| 6 | Brightness Level 5 | LED 2~LED 6 |
| 7 | Brightness Level 4 | LED 2~LED 5 |
| 8 | Brightness Level 3 | LED 2~LED 4 |
| 9 | Brightness Level 2 | LED 2~LED 3 |
| 10 | Brightness Level 1 | LED 2 |
Note: Brightness Indicator lights will stay illuminated while circuit it powered on.
MULTI-GANG INSTALLATION DERATING
| Single-Gang Rating | Double-Gang Rating | Triple-Gang Rating |
|---|
120 Vac,
60 Hz,
500 W Tungsten
| 120 Vac,
60 Hz,
400 W Tungsten
| 120 Vac,
60 Hz,
300 W Tungsten
300 W CFL/LED/
Electronic self-ballasted
| 300 W CFL/LED/
Electronic self-ballasted
| 300 W CFL/LED/
Electronic self-ballasted
500W ELV
400VA MLV
| 400W ELV
300VA MLV
| 300W ELV
200VA MLV
INSTALLATION
-
Warning: To avoid risk of fire and electrical shock, cut off the power at the circuit breaker or fuse before wiring
-
Remove existing switch: Remove existing wall panel and switch mounting screws. Carefully pull switch from wall box, identify and remove the wires attached to the switch, then remove the switch. Do not remove the wires from the wall at this time. (for new installations where an existing switch does not exist, skip this step.)
-
Identify the type of circuit
Note: If the wiring layout in the wall box does not resemble any of these configurations, consult an electrician.
IMPORTANT NOTE: For a Single-Pole application, note that one of the screw terminals from the old switch being removed usually is a different color (Black) or labeled Common. Tag the wire with electrician tape and identify as the Common (hot wire or load) in both the dimmer wall box and Single-Pole wall box. -
Typical Wiring (see wiring section)
-
Install and fix the dimmer:
Carefully position all wires inside the wall box, leaving enough room to insert the dimmer housing. Secure the dimmer with the mounting screws provided. -
. Install the wall panel
- Place the base plate over the installed dimmer and secure it using provided screws.
- Connect the face plate to the installed base plate and gently push it until it clicks into place.
WIRING
Single-Pole
Wiring Scheme 1 (neutral and hot wire)
Wiring Scheme 2 (hot wire only)
3-Way (neutral and hot wire)
3-Way (hot wire only)
Easy Answers
rablighting.com
Visit our website for product info
Tech Help Line
Call our experts: 888 722-1000
e-mail
Answered promptly – sales@rablighting.com
Free Lighting Layouts Answered online or by request
RAB WARRANTY: RAB’s warranty is subject to all terms and conditions found at rablighting.com/warranty.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>