Saxby 51898 Toba Battery Operated Mirror Instruction Manual
- June 13, 2024
- saxby
Table of Contents
Saxby 51898 Toba Battery Operated Mirror
Product Information
- Bulb Type: 1.2W LED (SMD), 6000K
- Battery: 3 x 1.5V AA
- Conformity: UKCA Directive requirements, EC Directive requirements
- Class: Class 3 product
- Waste Disposal: Do not dispose of with household waste, recycle where facilities exist
- Dimming: Not suitable for dimming
- IP Rating: IP44
Product Usage Instructions
- Care and Safety:
- Clean the product with a soft dry cloth. Do not use solvents or abrasive cleaners as they may damage the finish.
- For mirrors, use a damp cloth or a propriety glass cleaner. Do not use abrasive materials as they will damage the finish.
- Always switch off the power supply before changing lightbulbs or cleaning for safety.
- If the mirror becomes cracked or damaged, replace it immediately before using the fitting.
- Installation:
- This product is battery powered and exempt from IEE wiring regulations for bathrooms.
- The product is suitable for all areas of a bathroom.
- Choose a location that allows secure mounting, such as a stud wall framework.
- The product can be mounted vertically (portrait) or horizontally (landscape).
- Fitting/Replacing Batteries:
- Use 3x 1.5V AA batteries.
- Do not mix rechargeable and new/used batteries.
- Switch:
- To mount the product in portrait orientation, use the provided slots.
- To mount the product in landscape orientation, use the provided slots.
- Battery Tube:
- The battery tube is attached with Velcro.
- Connect the jack plug for battery connection.
For more information, please refer to the instruction manual provided with the product.
Thank you for purchasing this light fitting. Please read the instructions carefully before use to ensure safe and satisfactory operation of this product. Please retain these instructions for future reference.
Warning
- Please read these instructions carefully before commencing any work.
- This unit must be fitted by a competent and qualified electrician.
- Check the pack and make sure you have all the parts listed.
- Install in accordance with the IEE Wiring regulations and current Building Regulations.
- To prevent electrocution switch off and took out the batteries before installing or maintaining this fitting. Ensure other persons cannot restore the electrical supply without your knowledge. If you are in any doubt, please consult a qualified electrician.
- This light fitting should be connected to a fused circuit.
- If replacing an existing fitting, make a careful note of the connections.
- This product contains non-replaceable parts and cannot be serviced. If damage occurs the part should be scrapped.
- Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your local authority or retailer for recycling advice.
Layout
- This product is battery powered and is therefore exempt from IEE wiring regulations concerning bathrooms.
- This product is suitable for all areas of a bathroom.
- The chosen location should allow for the product to be securely mounted. (e.g. to a stud wall framework)
- This product can be mounted either vertically (portrait) or horizontally (landscape)
Installation
- Decide if the mirror is to be installed landscape or portrait. This mirror fixes to the wall by locating the keyhole shaped slots over the mounting screws in the wall. It is important to get the screw positions correct to ensure easy and secure fitting.
- Measure the distance between the hole centres on the fixing lugs. Mark the positions of the screw holes on the wall. Check for concealed pipes and wiring before drilling. Use suitable drill bits for masonry and ceramic tiles.
- Supplied wall plugs are for solid walls only. For all other wall types ensure correct fixings are used. Fit appropriate wall fixings and fit supplied screws. Screw heads must protrude approx 3-5mm from the wall to enable lugs to fit over adequately.
- Fit mirror onto screw heads – check the screw heads are securely located into the keyhole slots.
- Switch mirror on.
Fitting/Replacing Batteries
This product requires 3x 1.5V AA batteries
- The performance of the product will depend on the quality and type of batteries used. Always use good quality batteries. The battery tube is attached to the rear of the mirror with spring clips for easy access to batteries. It can also be completely removed from the product – by disconnecting the jack plug and socket.
- Loosen 2 screws on battery tube switch end. Remove lid, insert batteries, observing correct polarity (+ end of batteries towards switch end). Refit lid, secure screws and switch-on to test.
- Batteries are to be inserted with the correct polarity.
- Different types of batteries (alkaline, ordinary or rechargeable) or new and used batteries are not to be mixed.
- Exhausted batteries are to be removed from the product to prevent leakage.
- The supply terminals of batteries are not to be shortcircuited.
- Non-rechargeable batteries are not to be recharged.
- Rechargeable batteries are to be removed from the product before being charged.
- Do not dispose of used batteries with your household waste.
Technical Data
- Bulb Type: 1.2W LED (SMD), 6000K
- Battery: 3 x 1.5V AA
- Conformity with all relevant UKCA Directive requirements.
- Conformity with all relevant EC Directive requirements.
- This is a Class 3 product.
- Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or local store for recycling advice.
- This product is not suitable for dimming.
- This product is rated at IP44.
Care and Safety
We recommend cleaning with a soft dry cloth. Do not use solvents or abrasive cleaners as these could damage the finish. Mirror-Use a damp cloth or a propriety glass cleaner. Do not use abrasive materials as these will damage the finish. For your safety, always switch off the power supply before changing lightbulbs, or cleaning.
The mirror must be replaced immediately should it become cracked or damaged. This fitting must not be used without the mirror in place.
V5 21/09/2022
UK Manufacturer: BH17 7BY
EU Manufacturer: Brilliant AG, Brilliantstrasse 1, D-27442 Gnarrenburg
www.saxbylighting.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>