FOSHAN 18P.5.LLCPA.1 Cell Phone Signal Booster User Manual
- June 13, 2024
- Foshan
Table of Contents
FOSHAN 18P.5.LLCPA.1 Cell Phone Signal Booster
Product parameters
model
18P.5.LLCPA.1
Network
KW18P-LLCPA-B2/B4/B5/B12/B13/B17/B25/
parameter
Frequency Range | Frequency | Uplink | Downlink |
---|---|---|---|
LTE -B12 | 699~716 | 729~746 | |
LTE -B2 | 1850~1910 | 1930~1990 | |
LTE -B4 | 1710 – 1755 | 2110 – 215 | |
LTE -B13 | 777~787 | 746~756 | |
LTE -B5 | 824~849 | 869~894 | |
LTE -B25 | 1850~1915 | 1930~1995 | |
LTE -B17 | 704-716 | 734-746 | |
Output Power | 20±1 dBm | 11±1 dBm | |
Gain | 59±1 dB | 58±1 dB | |
Bandwidth | 17M+10M+25M+65M+70M | ||
--- | --- | ||
Ripple in Band | LTEB12/17≤6dB;LTE -B13≤6dB;CDMA≤ |
6dB;LTE-B25≤6dB;LTE-B4≤6dB;LTE – B2≤6dB
Spurious Emission| 9KHz~1GHz| ≤ -36 dBm
1GHz~12.75GHz| ≤ -30 dBm
Intermodulation Products| 9KHz~1GHz| ≤ -36 dBm
1GHz~12.75GHz| ≤ -30 dBm
VSWR| ≤3
MTBF| >50000 hours
Power Supply| AC:100~240V, 50/ 60Hz;DC:5V 3A
Power Consumption| < 6W
Impedance| 50 ohm
Mechanical Specification
RF Connector | N-Female N |
---|---|
Dimensions (DWH ) | 25316028mm |
Packing size (DWH ) | 33522050mm |
Net weight | <0.53KG |
Gross weight | <0.87KG |
Installation Type | Wall Installation |
Environment Conditions | IP40 |
Humidity | < 90% |
Operating Temperature | -10℃ ~ 55℃ |
Product display
Installation steps
Step 1: Install the outdoor antenna on the roof or other positions where
you can receive 4 bars of signal or more
Step 2: Connect the outdoor antenna to the BTS port via the cable and tighten the connectors at both ends, make the outdoor antenna point to the base station
Step 3: Connect the indoor antenna to the MS port, and place the indoor antenna at a higher position so as to increase signal coverage
Step 4 : After connecting and tightening the two antennas, plug in the power supply and check the condition of the signal display light
Step 5 : Check whether the phone signal has been improved or not. If it is not ideal, you can adjust the height or direction of the outdoor antenna. A good outdoor signal is half of the success.
Attention: There must be a solid wall between the indoor antenna and the
outdoor antenna to prevent self oscillation.
installation drawing
Application Scenario
frequently asked question
FAQ | Solutions |
---|
After the installation, the signal improvement is not significant, and the indoor coverage area is small|
- Adjust the position and direction of the outdoor antenna
- Check if the cable is properly connected
- Raise the outdoor antenna so that it can receive better signals
- Replace high-power amplifier
- Replace a high gain outdoor antenna
The phone signal is full, but the call quality is poor| The distance between
outdoor and indoor antennas are too close, so it is necessary to increase the
distance between them, or increase barrier isolation between them
After installation,
the signal did not improve, but it was worse
| The distance between outdoor and indoor antennas are too close, so it is
necessary to increase the distance between them, or increase barrier isolation
between them
I have been using it normally before, but suddenly the signal is not good
after using it for a period of time|
- Check if water ingress at outdoor cable joints
- Check if the power indicator light is normal
- If there is no water ingress into the cable and the power indicator light is normal, it is possible that the amplifier has malfunctioned and needs to be returned to the factory for repair
FCC Statement
This equipment should be installed and operated with a minimum distance of
20cm between the radia to randyour body .
The antenna for the device must be installed to comply with the 10 meter above
ground maximum antenna height limitation
(1) Usage of unauthorized antennas, cables, and/or coupling devices may
result in poor effect and, in severe cases, equipment damage.
(2) a complete list of authorized antennas, cables, and/or coupling
devices
OTHER MODEL
Name | Model | Gain/Loss | Photo |
---|---|---|---|
Indoor Antenna | Panel Antenna (default) | TX.BG.2 | 9dbi @698-2700MHz |
Ceiling Antenna| TXXD.3| 3dbi 698-2700MHz|
Outdoor Antenna| Log-periodic Antenna (default)| TX.DS.2| 10dbi @698-2700MHz|
| Yagi Antenna| TX.BM.8.1| 8dbi @698-2700MHz|
cable| Coaxial cable with N male connector (default)| X .13B1| 3dbi
@698-2700MHz|
(3) the default antenna, cable. and/or coupling device that are shipped with the booster Log-periodic Antenna, Panel Antenna and Coaxial Cable.
(4) The antenna is equipped with a U-shaped mounting bracket. The log- periodic antenna should be installed in a place with good outdoor signal. The panel antenna should be installed indoors and near the main device. If the amplification effect is not good after the installation is completed. the direction of the log-periodic antenna can be gradually adjusted to achieve better effect.
(5) The device has automatic sleep function. strong anti-interference ability. over-power protection function, good heat dissipation design, and no radiation. The working noise is as low as 6DB.
This device complies with Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this device must
accept any interference, including interference that may cause undesired
operation of the device.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause
undesired operation Foshan lintratek Technology Co.. Ltd. Room 101. First
Floor. No. 8. Xiaowugang Garden Ceramic Factory. Shiwan. Chancheng District,
Foshan. China Contact: Peter Shi Tel:86-0757-82805302 Email:
ss_shi@126.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>