FOSHAN YCB Remote Control User Manual
- June 4, 2024
- Foshan
Table of Contents
FOSHAN YCB Remote Control
Connecting the remote control
WARN:
Changes or modifications to this unit not expressly approved by the party
responsible for compliance
could void the user’s authority to operate the equipment.
NOTE:
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device.
- A New remote control has to establish a new connection to the cooker hood when used for first time. One remote control could possibly control several cooker hood at the same time.
Connection process between remote control and cooker hood
- Within 15 seconds after the cooker hood connects to the power supply, long press for 5 seconds, the indicators light begin flashing from one button to another, the cooker hood is in connection mode, press any button on remote control to confirm the connection. The connection process finished and the remote control can be used for speed selection, lighting and timer setting.
- If you want to connect again, you will need to clear the code that has been set up previously.
- To clear the code, press for 5 seconds, the indicators light begin flashing from one button to another, the cooker is in connection mode. Then, press again for 5 seconds, the previous connection code is cleared.
- When the previous code has been cleared, the cooker hood back to standby mode, press for 5 seconds, the indicate light flashing from one button to another ,the cooker hood is in connection mode, then, press any button on remote control to confirm the connection.
Remote control
-
Lighting button
Press the lighting button once, the light will be on, and the indicator lights of lighting button and power button will be on. Press again, the light will be off. The indicator lights of lighting button and power button will be off. Cycle in turn. -
Turning on/ Increasing motor speed button , the motor has low, middle and high totally 3 levels.
- Press once, the indicator light will be on, and the motor will work at low speed .
- When the motor works at low speed, press again, the motor will change to middle speed.
- Base on the middle speed condition, press again, the motor will change to the high speed.
- Base on the high speed condition, press again, the hood will still work at high speed.
-
Turning off/Decreasing motor speed button
- Press the and the motor will be shift to a lower speed. Repeating press the button, it will keep on decreasing the motor speed till the cooker hood turning off. The indicator light will be off.
-
Timer button
- Press the timer button to enter the timer setting state. The initial timer setting defaults to 5 minutes. Automatically confirm the running timer function after 2 seconds of setting. After confirmation, it will begin to decrease by seconds. When the set time decreases to zero, the motor will automatically cut off the power supply.
- When using the timer function of the remote control, if the control panel changes the time setting, the timer function of the hood controlled by the remote control will automatically default to the time set by the last time. After 5 seconds, it starts to decrease every second. Changing the set time will run according to the new set time.
- After confirming the timer function, the hood will enter the timer state. At this time, press the timer button again to cancel the timer function.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>