PG CL-SM2200L-3H 2200 Lumen 3 Head Solar Motion Activated Security Light Instruction Manual

PG CL-SM2200L-3H 2200 Lumen 3 Head Solar Motion Activated Security Light

PRECAUTIONS:

Please read and understand this entire manual before installing or operating this light fixture.

• This light fixture should be installed outdoors to a wall or eave.
• The solar panel should be installed where it can get the most sun.
• Do not ait the solar panel wire. Oisoontinue use if the wi’ebecomes frayed or broken.
• Do not immerse components in liquid.
• Do not use any other charging device other than the single solar dlarfjng panel provided with this light. OQng so may result in injury or damage to the light and voids any warranty.
• Position the cord so it is secura4y fastened and will not result in hazards (such as tripping).
• Your motion light and solar panel are both water-resistant.
• Never look directly into the solar motion light when illuminated.
• Operating temperat\Jre ·13’F to 113’F (·25’C to 45’C)

WARNING: To prevent SERIOUS INJURY OR DEATH, never allow children near the battery. If a battery is swallowed, seek immediate medical attention.
WARNING: When replacing the battery, DO NOT use an old battery: Make sure to match the replacement battery specifications with the batt8fy that has been removed (Li-ion battery, 18650 3.7V 2200mAh). DO NOT DISPOSE OF THE Battery IN ARE. Battery MAY LEAK OR EXPLODE.

RECOMMENDED INSTALL HEIGHT:
Install the light between 6.5-8.5 feet above the ground. The fixture will provide a detection distance of up to 70 feet.

LOCATION OF SOLAR PANEL:

For the best results, install your solar panel in an area where it can absorb maximum sunlight during daytime hours. Be aware of objects such as treesor property overhangs that may L.✓ impede the panel’s ability to generate a charge.

PRE-INSTALLATION:

1. Before assembly, compare package contents with the hardware list to make sure all parts are present.
2. Prior to installing the lights, an initial charge is needed and should be done in the OFF position for at least 1 to 3 days in direct sunlight before use (see page 5, fig 5 for mode selections). Make sure to plug the solar panel into the lights to charge the battery. Afterward, the included rechargeable battery will be charged sufficiently for operation.
3. When fully charged and ready to install, select a suitable location that can support the weight of the fixtures.
4. The solar panel comes with a 15 ft. wire. The maximum distance between the solar panel and light is 15 ft.
5. The motion sensor is light-sensitive. For best performance at night, ensure there is no interfering light preventing the sensor from working correctly.
6. Estimated installation time: 15 Minutes

INSTALLATION

1. Select the desired position for the security light and solar panel. The maximum distance between the security llght and solar panel Is 15 ft
   Use a drill and a 118″ drill bit to drill (2) holes on your preferred mounting surface, utilizing the mounting bracket (E) screw holes as your guide. Use (2) wall anchors (D), insert into each hole, then use (2) screws (C) to fasten the mounting bracket (E) to the surface. Make sure the clip side is facing out as shown in Fig 1.

2. FOR WALL MOUNT:
   Before connecting the light to the mounting bracket, switch the Mode to the Auto position (see Fig 5 on page 3). Connect the light (A) to the mounting bracket (E) as shown in Fig 2.

3. FOR EAVE MOUNT:
   you are eave mounting the security light, ensure the ceiling is level and the fixture can support the weight of the light. Follow Step One to secure the bracket (E). Before connecting the light to the mounting bracket, switch the Mode to the Auto position (see Fig 5 on page 3). Connect the light (A) to the mounting bracket (E) as shown in Fig 3.

4. Use a drill and a 118″ drill bit to drill (4) holes on your preferred mounting surface, utilizing the solar panel (B) screw holes as your guide. Use (4) wall anchors (D), insert into each hole, then use (4) screws (C) to fasten the solar panel (B) to the surface as shown in Fig 4.
   Note: Make sure the distance between the 1/ght and solar panel are within 15 feet.

5. Connect the solar panel wire to the light as shown in Fig 5. Installation is complete. You are now ready to enjoy your new LED security light.

TESTING THE LIGHT

NOTE: It is recommended that the light be tested before being placed into regular operation.
NOTE: Testing the light indoors or lower than 7 ft. from the ground may not enable the light to work optimally when mounted outdoors.

Before placing the light in Auto operation, it is best to set the preferred light direction, then test the light and motion sensor.

• To set the light position:
  Switch the Mode to On (Fig A). This will turn the light on and you can adjust the lights to your desired position.

• To test the motion position:
  Switch the Mode to Auto. Switch the Time to Test (Fig B). The light may initially turn on for a short time. When the light turns off, you are now ready to test the motion sensor, whether it is day or night The light will activate for 5 seconds every time motion is detected. Adjust head and motion sensor to desired angles.

• Adjust the Sensitivity (Fig C) and Motion Sensor (Fig D) to meet your desired detection.

• When the motion preference are achieved, switch the Time to 30, 60, or 120 seconds. Your light is now ready to use.

SWITCH FUNCTIONS & BATTERY LOCATION

The different control s1,Hches adjust the light’s illumination time, light sensitivity, and range of motion detection.
Time: Determines the duration of the light once motion is detected: 30 seconds, 60 seconds, or 120 seconds.
TEST allows the positioning of the light’s motion sensor tobe tested day or night. Once the motion sensor is in the desired position, attempt to trigger the light by moving in the intended detection zone. If the light illuminates, the motion sensor is positioned correctly. You are now ready to move the switch to the preferred time/duration option. The light ,…;11 now only turn on in darkness.

SENSITIVITY: Controls the distance of the range of m01ion detection: low, medium, or high.

MODES:

• Auto: The light  will come on at the desired time, and sensitivity level set between dusk & dawn.
• On: This function overndes motion detection. The light will remain on for 90 minutes.
• Off: The light  will be turned off.

Prior to accessing the battery, tum the Mode to the Off position. Use a screv.driver to remove the (2) screws on the back ol the light. Remove the battery access panel as shown.

when replacing the battery, follow the correct polarity, match the battery specification. Use only a new LI-ion rechargeable battery, 18650 3. 7V 2200mAh.

• Note: DO NOT U$8 an Oki battery.
• Noto: Whon replacing baltory, rocycfo used battery or of lhom ln accordat>CO with tho IOc.8.I rogutatiOtlS.
• Note: Aftt)r the ballery has been replaced, $wit.ch to th(J Auto in Mode. The li{Jhl will enter Auto Mode and the fight i$ roedy for use.

To adjust the heads for preferred detection, gently rotate the left and right lamp heads up or down or side to side. The center light is not adjustable. To adjust the motion sensor for preferred detection, gently rotate up or down or side to side.

CARE AND MAINTENANCE

• From time to time, ensure the plug between the solar panel and light is securely connected. Discontinue use if the wire becomes frayed or broken.
• Its dovisdore to agust ine angie orte solar paner to opumize te exposure to te sun during te winter monins.
• It is advisable to adjust the angle of the solar panel to optimize the exposure to the sun during the winter months.
• The solar panel should be cleaned with a damp cotton cloth regularly. That will en sure optimal performance and battery charging. Periodically, utilize the same technique to clean the lenses of the motion lights.
• Never let any abrasive material come into contact with the solar panel.

TROUBLESHOOTING

The solar panel is not positioned in direct sunlight

The control dial is set to off

| Replace the battery

Position the solar panel so it gets direct sunlight

Check the time and mode settings to ensure light

is not off

The light comes on during

the day

| The light may be mounted in an area that is too shaded| Relocate the light to an area that has more light and noobst ructions
The light comes on when it

shou dn’t

| The sensor may sensing small animals or traffic| Reposition the sensor
n,e lights flashor pulse| The battery may be low

The sensor may be sensing shadows

| Turn the unit offand allow the

battery to recharge. Full charge between 1 and 3 days

Relocate the light to an area withless or no shadows

EYES:

• DO NOT look directly at the LED lights.
• DO NOT remove the LED lights protective covering.

This product has a two-year limited warranty from the date of defects, purchase. whether This caused guarantees by materials against failor ure due workmanship. to factory The
warranty is non-transferable and only pertains to the original

• Using limited outdoor: s in extreme weather conditions.
• Any Opening attempts the to product’s update, housing. remodel or fix the unit yourself.
• Using any other charging device other than the single

solar charging panel provided with this light. Thi s device complies IMth Part 15 of the FCC rules. Operation is subject to the f<lllo1Mng two conditions: (1) this device may not cause hannful interference.and (2) this device must accept any interference received, induding interference that may cause undesired operation. If you have questions or are missing parts, please contact customer service at 1-888-745-4837 <fPG

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>