DEFIANT KPDK02A Fingerprint Keypad Deadbolt Installation Guide
- October 30, 2023
- DEFIANT
Table of Contents
KPDK02A
Rev. 1.0
INSTALLATION GUIDE
FINGERPRINT KEYPAD DEADBOLThttps://www.youtube.com/playlist?list=PLzJoBhMyZvYfAjL3DTjwgUxIudrtvN0pD
THANK YOU
We appreciate the trust and confidence you have placed in Defiant through the
purchase of this fingerprint keypad deadbolt. We strive to continually create
quality products designed to enhance your home. Visit us online to see our
full line of products available for your home improvement needs. Thank you for
choosing Defiant!
Safety Information
Read the precautions and instructions in this manual before installing and using this lock. Save this manual for future reference.
- Do not attempt to disassemble any internal components of the lockset. Doing so will void the limited warranty.
- Do not drop or hit the lockset. Too much shock may result in permanent damage.
- Do not use pins or sharp objects to press the keypad and fingerprint sensor.
- Always create a backup of information you wish to keep (Master Code, User Codes, etc.).
- Promptly change the master code before operating this lockset.
- Restrict access to your lock’s interior assembly and routinely check your settings to ensure they have not been altered without your knowledge.
NOTE: Before beginning installation of product, make sure all parts are present. If any part is missing or damaged, do not attempt to assemble, install or operate the product. Call the Customer Service Team at 1-866-308-3976 or visit www.homedepot.com.
Care and Cleaning
- Remove locks, or do not install locks, prior to painting your door.
- Periodically clean with mild soap and a soft cloth only.
- Do not use any abrasives or chemical products containing alcohol, benzene, or acids, and avoid using sharp or abrasive objects to clean this lockset.
- Do not allow any water or liquids into the lockset during installation.
- This lockset is designed to provide the highest standard of product quality and performance. Care should be taken to ensure a long-lasting finish. When cleaning is required use a soft, damp cloth.
- Using lacquer thinner, caustic soaps, abrasive cleaners, or polishes could damage the coating and result in tarnishing.
WARNING: Do not use electric drill or electric screwdriver to tighten screws.
Installation
Preparing the door and checking dimensions
- Measure to confirm that the hole in the door is 2-1/8 in. (54 mm).
- Measure to confirm that the backset is either 2-3/8 in. or 2-3/4 in. (60 or 70 mm).
- Measure to confirm that the hole in the door edge is 1 in. (25 mm).
- Measure to confirm that the door is 1-3/8 in. to 2 in. (35 mm to 50 mm) thick.
Installing the latch and strike
- Hold the latch (C) in front of the door hole, with the latch face flush against the door edge. No adjustment is required if slotted hole is centered (backset 2-3/8 in.); Rotate and pull backwards the latch to extend, then rotate it back as shown if slotted hole is not centered (backset 2-3/4in.).
2a. Installing latch and strike – door edge chiseled
Install the latch in door edge hole directly with latch screws (K) if your
door edge is chiseled.
2b. Installing latch and strike – door edge not chiseled
Use a flat head screwdriver to remove rectangular face and rotate off part of
the latch face, then install drive-in collar (N) if your door edge is not
chiseled. Then install latch in door with wood block and hammer.
- Insert a flat head screwdriver into latch slot and rotate to test if deadbolt works smoothly.
- Install strike (J) in the door frame with strike screws (L), and in order to maintain BHMA Grade 3, you must install the reinforcement plate (I).
Installing exterior assembly
IMPORTANT: Before installation, make sure the latch is fully retracted (in the unlocked position).
- Route the power cable (M) below the latch.
- Install exterior assembly (B) and send the power cable through the bottom horizontal slot in the mounting plate (D).
- Secure the mounting plate with the mounting screws (E).
Pre-Installation
TOOLS REQUIRED
PACKAGE CONTENTS
Part | Description |
---|---|
A | Backup Key |
B | Exterior Assembly |
C | LatchJ |
D | Mounting Plate |
E | Mounting Screws |
F | Interior Assembly |
G | Battery Cover |
HS | HScrews |
I | Reinforcement plate |
h | Strike |
K | KLatch Screws (21 mm) |
L | Strike Screws (38 mm) |
M | Power Cable |
N | Drive-in Collar |
O | Reset Tool |
Installing interior assembly
IMPORTANT: Do not load batteries until lock is completely installed.
-
Remove the battery cover (G).
-
Connect the power cable (M) and ensure tight cable connection.
-
Rotate the thumb turn in vertical position and install the interior assembly (F).
-
Test the thumb turn for smooth rotation. If thumb turn doesn’t rotate, repeat last step, making sure the thumb turn in vertical position.
-
Secure the interior assembly with the supplied screws (H).
IMPORTANT: Lock knob will only rotate to the lock position in either the clockwise or counterclockwise direction based on your door handing, not both.
2b. Installing latch and strike – door edge not chiseled
Detecting left/right hand door installation
Reset the lock to teach the lock the orientation of the door.
IMPORTANT: This step is required and crucial for the lock to operate
properly.
-
While the door is OPEN and UNLOCKED, load three AA batteries into the interior assembly.
IMPORTANT: For best results, use new, non-rechargeable alkaline batteries only. -
Press and hold the Reset button on the interior assembly using the reset tool (O) included in package.
-
Load the last battery and keep holding the reset button for at least 3 seconds, until you hear the sound of “beep”. The latch bolt will extend to learn the orientation of the door.
Warranty
LIMITED LIFETIME FOR MECHANICAL AND 1 YEAR FOR ELECTRONICAL WARRANTY
The retailer of this product, hereby warrants, subject to the conditions set
forth below, that it will either repair or replace, at its option, this
product if it proves to be defective by reason of improper workmanship or
materials within the original purchaser’s lifetime. In order to obtain
repairs or replacement under this limited warranty you must bring this product
to the retailer’s store in which you bought it.
Original purchaser: This limited warranty is limited to the original purchaser
at retail of this product from retailer.
Except to the extent prohibited by applicable law, no other warranties,
whether express or implied, including the warranties of merchantability and
fitness for a particular purpose, shall apply to this product. Under no
circumstances shall retailer be liable for consequential or incidental
damages in connection with this product. To the extent retailer is prohibited
by applicable law from excluding implied warranties, the duration of such
implied warranties which are not excludable shall be the original purchaser’s
lifetime. Some states do not allow the limitation on how long an implied
warranty lasts, so the above limitation on the duration of implied warranties
which are not excludable, if any, may not apply to you. Some states do not
allow the exclusion or limitation of incidental or consequential damages, so
the above limitation or exclusion of incidental or consequential damages may
not apply to you. Retailer neither assumes nor authorizes any representative
or other person to assume for it any obligation or liability other than such
as is expressly set forth herein. This limited warranty gives you specific
legal rights, and you may also have other rights which vary from state to
state.
****Questions, problems, missing parts? Before returning to the store,
call Defiant Customer Service
8 a.m. – 7 p.m., EST, Monday-Friday, 9 a.m. – 6 p.m., EST, Saturday
1-866-308-3976
HOMEDEPOT.CA
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>