FOSHAN BT499 Wireless Speaker Box Instruction Manual
- October 30, 2023
- Foshan
Table of Contents
FOSHAN BT499 Wireless Speaker Box
Product Information
The Wireless Speaker Box is a portable speaker that supports USB, FM, Bluetooth, and TWS. It has a Bluetooth version of 5.2 and a distance range of up to 15m. The speaker size is 3” and has an output power of 3W. It has a frequency response of 60Hz~10KHz and a signal-to-noise ratio of 80db. The speaker box can be charged using a USB charging cable and has a battery capacity of 500mAh. It has a playtime of 1-2 hours and takes around 3-5 hours to charge.
Product Usage Instructions
Connecting the Wireless Speaker
To connect the wireless speaker, turn on the speaker unit and the mobile
device or other devices that you want to connect it with. Search for the
unit’s model name 2BOOM-BT499 to pair the two devices. Once paired before, it
will automatically connect after the unit is turned on.
Wireless Mode
Turn on the speaker, and it will come into wireless mode directly. After
pairing the device, it can play music. Press the Play/Pause button to pause or
resume music playback. Use the Previous song/volume down and Next song/volume
up buttons to navigate songs, and use the Volume +/- buttons to adjust the
volume.
USB Mode
Insert a USB flash drive into the USB slot, and the speaker box will read
the MP3 format music automatically. Use the Play/Pause button to pause or
resume music playback. Use the Previous song/volume down and Next song/volume
up buttons to navigate songs, and use the Volume +/- buttons to adjust the
volume.
FM Radio Mode
Press the Scan button to search FM channels automatically. This operation
will scan all FM stations and prerecord them to memory. The scan procedure
will take several minutes and cannot be interrupted. Once completed, use the
Previous song/volume down and Next song/volume up buttons to navigate songs,
and use the Volume +/- buttons to adjust the volume.
RGB Light Mode
There are three different RGB light modes. Short press the LED button to
switch between different RGB modes. The last used RGB light mode will be
stored in the speaker memory before switching it off, and it will be restored
once the speaker unit is powered on the following time. Long-press the LED
button can open/close the light.
TWS Mode
Two of the same model speakers can be connected to one wireless device at
the same time. First, turn the speakers on, then choose one unit and long
press its MODE button for several seconds. You will hear the sound of Ding~ to
indicate that the two units have paired successfully. Please ensure before
pairing that the two units are not connected with other devices.
Charging
Plug the USB cable into the speaker’s charging port and connect it to a
power source. The RED LED indicator on the panel will be on when the unit is
charging.
Caution: Any changes or modifications to this device not explicitly
approved by the manufacturer could void your authority to operate this
equipment. This device complies with part 15 of the FCC Rules. Operation is
subject to the following two
conditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
ACCESSORIES
- Wireless Speaker Box: 1PC
- Charging Cable: 1PC
SPECIFICATIONS
- Product size: 100100180mm
- Support: USB,FM,bluetooth,TWS
- Bluetooth version: 5.2
- Distance: 15m
- Speaker size: 3”
- Output power: 3W
- Frequency response: 60Hz~10KHz
- Signal to noise ratio: 80db
- USB charging: USB charging cable
- Battery capacity: 500mAh
- Play time: 1-2hrs
- Charging time: 3~5hrs
DESCRIPTION OF PARTS
- USB port
- Charging port(DC5V)
- Charging LED
- ON/OFF
- Speaker modes button(Mode1:Blue-Connect; Mode2:FM Mode; Mode3:USB/TF) / Long-press to connected the TWS
- Play/Pause/Scan(Auto search in FM mode) / Long-press the button can connect or disconnected the Bluetooth-Connect
- Previous song/vol-
- Next song/vol+
- RGB light modes
HOW TO CONNECT THE WIRELESS SPEAKER
Turn on the speaker unit and the Mobile or other devices, and search for the
unit’s model name “2BOOM-BT499” to pair the two devices. Once paired before,
it will automatically connect after the unit is turned on.
WIRELESS
Turn on the speaker and it will come into the Wireless mode directly. After
pairing the device, it can play the music. Press button to Play/Pause. Press
the button to be the previous track or next track, and press the “VOL+” or
“VOL-” button to increase or decrease the Volume.
USB
Insert the U flash memory into the USB slot, the speaker box will read the MP3
format music automatically. Press the button to Play/Pause. Press the button
to be the previous track or next track, and press “VOL+” or “VOL-” button to
increase or decrease the Volume.
FM RADIO
Press /SCAN to search FM channels automatically. This operation will scan all
FM stations and Prerecord them to memory. The scan procedure will take several
minutes and cannot be interrupted. Once completed, press the button to be the
previous track or the next track, and press the “VOL+” or “VOL-” button to
increase or decrease the Volume.
RGB LIGHT MODE
There are three different RGB light modes. Short press the “LED” button to
switch between different RGB modes. The last used RGB light mode will be
stored in the speaker memory before switching it off, and it will be restored
once the speaker unit is powered on the following time. Long-press the LED
button can open/close the light.
TWS
Two the same model speakers can be connected to one wireless device at the
same time. First, turn the speakers on, then choose one unit and long press
its “MODE” button for several seconds; then you will hear the sound of “Ding~”
to indicate that the two units have paired successfully. Please ensure before
pairing that the two units are not connected with other devices.
CHARGING
Plug the USB cable into the speaker’s charging port and connect to the power
source. The RED LED indicator on panel will be on when the unit is charging.
Statue | Blue light | Red light |
---|---|---|
Quick flashing | Searching blue-connect / FM SCAN | / |
Slow flashing | Playing | / |
Long bright | Pause / No music playing | Charging |
FCC Warning
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipmentoff and on, the user is encouraged to try to correct the interference by one or more of thefollowing measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications to this device not explicitly approved by the manufacturer could void your authority to operate this equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 0cm between the radiator and your body.