AENO AAP0004 Air Purifier User Guide
- June 13, 2024
- AENO
Table of Contents
Quick Start Guide
Air Purifier AP4
(Model AAP0004)
11.01.23 | v 2.4.2
AAP0004 Air Purifier
| 
---|---
| 
|
The AENO AP4 Air Purifier is designed to disinfect and clean indoor air from allergens, pollen, fungal spores, dust particles, smoke, animal hair, and unpleasant odors.
Specifications
Supply voltage: DC 12 V, 2 A.
Rated power: 24 W.
Power adapter input voltage: AC 100–240V, 50/60 Hz.
Air flow rate: 200 m³/h.
Noise level: in the night mode 22 dB (at a distance of 1m).
Coverage: Up to 35 m².
Indoor air purification time: 0,5 hours.
Net weight: 2.1 kg.
Dimensions: Ø205 mm × 385 mm.
Package Contents
AENO AP4 Air Purifier (See Figure a), power adapter, HEPA filter, quick start guide, warranty card.
Limitations and Warnings
ATTENTION! The device is equipped with a built-in UV lamp. It is not
allowed to disassemble the device and turn it on when disassembled, because it
may be very harmful to eyes.
Make sure the purifier is unplugged before maintenance. Do not immerse the
purifier in water or any other liquid. Do not use aggressive and flammable
chlorine- or alcohol-containing agents to clean the purifier. Use the device
as described in this Quick Start Guide and the complete User Manual only.
Failure to follow the instructions may result in fire and other hazardous
situations, as well as injuries. Do not use the device if it is damaged or
cracked. Do not install the device outdoors or near sources of water,
including humidifiers. Do not expose the device to direct sunlight, moisture
or vibration. Do not drop, throw, disassemble the device, or try to repair it
on your own. Do not lay the power cable near radiators, stoves, or heaters. Do
not use cleaning agents or detergents to clean the device. Do not dispose of
the device with unsorted urban waste, because this will be harmful for the
environment. For more information on proper disposal, please contact your
local waste collection and disposal company. Keep children away from the
device. There is a risk of serious injury and electric shock. This device is
intended for use by adults only.
Warnings, precautions, and instructions contained herein may not contain every
possible hazardous situation. Please use common sense when operating the
device.
Initial Setup
Before operation, you should remove the packaging from the HEPA filter. To do
this, please turn the purifier upside down and remove its cover by turning it
counterclockwise (See Figure b). Then, remove the HEPA filter from the device
body using the fabric strips (See Figure c), remove the filter packaging, and
insert the filter back into the device body. Tighten the cover by turning it
clockwise (See Figure d). After that, you should connect the air purifier to
the source of power (mains socket) using the power adapter included in the
package of supply. The power connector of the adapter must be inserted into
the power port in the device casing, while the plug of the adapter – into the
mains socket.
ATTENTION! Never use a non-original power adapter to connect to and power
on the device, as this may damage the purifier.
Button Panel Control
The purifier will be switched to the Standby Mode upon connection to the mains socket using the power adapter. The control panel of the device contains the following 6 LED buttons (See Figure e):
- POWER button used to switch the purifier from the Standby Mode to the Operation Mode, as well as to turn off the purifier, or turn on the anion filter.
- SLEEP, SPEED MID and SPEED HIGH buttons used to switch the fan speed of the purifier in the following way: Sleep – quiet mode, Speed Mid – medium rotation speed of the fan, Speed High – high rotation speed of the fan;
- FILTER button that is blinking every time the filter shall be replaced (an audible signal will also be emitted. You may stop it by pressing this button again);
- UV-C button used to turn on the UV diode intended for air disinfection.
Maintenance
The HEPA filter shall be cleaned on a regular basis, but never rinsed up with
water or used after the end of service life. Please dry the HEPA filter
regularly in the sun.
Do not remove dust from the HEPA filter with a vacuum cleaner or a water jet.
The HEPA filter shall be replaced every 2,200 hours of operation (i.e. every
3-6 months). To remove dust from the HEPA filter, you shall remove it from the
purifier casing. Use a soft cloth with a neutral (non-aggresive) detergent to
remove dust or large pieces of dirt from the surface of the HEPA filter. The
HEPA filter shall be installed back in the purifier casing only after it gets
dried. If the device is not planned to be used for a long time, please store
it covered with a dustproof bag in a dry, cool and well-ventilated area. It is
also recommended to power on the device from time to time for at least a few
minutes in order to keep it in a good working condition.
ATTENTION! Do not allow water to enter the purifier.
Troubleshooting
-
The purifier does not turn on. Make sure that the purifier is plugged into the mains socket, and that there is no power supply failure, as well as that the circuit breaker is on, and that the fuses are intact, and that the filter change
LED is blinking red. -
The device makes a loud noise. Make sure that nothing is stuck in the fan, and that the purifier is not tilted. If the noise is still too loud, try to reduce the fan speed using the Speed Mid or the Sleep button. Also, use Sleep Mode to operate the purifier at night.
-
Unpleasant odor coming from the purifier. If the device emits a plastic smell during the first few hours of operation, this is deemed to be normal. However, the device may also emit an unpleasant odor when the filter is clogged. In this case, the filter must be cleaned or replaced. If you smell burning, unplug the purifier immediately. Then, contact our Support Dept or the Seller of the device for assistance.
-
The filter change LED is blinking after the filter was replaced or cleaned. Click on the Filter button to restart the filter replacement timer, and the LED indicator will be turned off.
ATTENTION! If your problem persists, please contact your local supplier
or the service center for support. Please do not disassemble the device or try
to repair it on your own.
ASBISc reserves the right to modify the device and to make edits and changes
to this document without prior notice to users.
The warranty period and service life shall be 2 years as from the date of
purchase of the device.
Manufacturer: ASBISc Enterprises PLC, Iapetou, 1, Agios Athanasios, 4101
Limassol, Cyprus. Made in China. For current information and details on the
device description and specification, as well as connection process,
certificates, warranty and quality issues, see relevant Installation and
Operation Manuals available for downloading at
aeno.com/documents. All trademarks and names
herein are the property of their respective owners.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>