Monoprice 43392 Blackbird Toslink S/PDIF 4×1 Switch User Manual

Monoprice 43392 Blackbird Toslink S/PDIF 4×1 Switch

SAFETY WARNINGS AND GUIDELINES

Please read this entire manual before using this device, paying extra attention to these safety warnings and guidelines. Please keep this manual in a safe place for future reference.

• This device is intended for indoor use only.
• Do not expose this device to water or moisture of any kind. Do not place drinks or other containers with moisture on or near the device. If moisture does get in or on the device, immediately remove it from its power source and allow it to fully dry before reapplying power.
• Do not touch the device, the power cord, or any other connected cables with wet hands.
• Do not expose this device to excessive vibration, extreme force, shock, or fluctuations in temperature or humidity.
• Do not expose this device to excessively high temperatures. Do not place it in, on, or near a heat source, such as a fireplace, stove, radiator, etc. Do not leave it in direct sunlight.
• Clean using a soft, dry cloth only. Do not use chemical cleaners, solvents, or detergents. For stubborn deposits, moisten the cloth with warm water.
• This device has no user-serviceable parts. Do not attempt to open, service, or modify this device.

INTRODUCTION

This Toslink® S/PDIF 4×1 Switch allows you to connect up to four Toslink digital optical S/PDIF audio source devices to a single output device, such as a television or amplifier. It supports 2-channel high definition audio sources, including LPCM, DTS®, and Dolby Digital™. It has a 96kHz sampling rate, supports signal re-timing, and can transmit audio to distances up to 131 feet (40 meters) using an optical cable with a loss of less than 0.2dB/m. It includes an IR remote control.

FEATURES

• Connect up to four Toslink® digital optical S/PDIF audio sources to a single output device, such as an amplifier or television
• Supports 2-channel high-definition audio sources, including LPCM, DTS®, and Dolby Digital™
• 96kHz sampling rate
• Supports signal re-timing
• Can transmit audio to distances up to 131 feet (40 meters) using an optical cable with a loss of less than 0.2dB/m
• Over-voltage protection
• USB powered

CUSTOMER SERVICE

The Monoprice Customer Service department is dedicated to ensuring that your ordering, purchasing, and delivery experience is second to none. If you have any problem with your order, please give us an opportunity to make it right. You can contact a Monoprice Customer Service representative through the Live Chat link on our website www.monoprice.com or via email at support@monoprice.com. Check the website for support times and links.

PACKAGE CONTENTS

Please take an inventory of the package contents to ensure you have all the items listed below. If anything is missing or damaged, please contact Monoprice Customer Service for a replacement.

• 1x Toslink® S/PDIF 1×3 Splitter
• 1x IR Remote Control
• 1x IR Receiver
• 1x USB Power Cable
• 1x User’s Manual

PRODUCT OVERVIEW

SAMPLE CONNECTION DIAGRAM

CONNECTION

Perform the following steps to connect the splitter to your system.

1. Ensure that all devices to be connected are powered off and disconnected from their power sources.
2. Using a Toslink® digital optical S/PDIF cable (available separately), plug one end into the optical input on your output device (e.g., amplifier, TV, etc.), then plug the other end into the OUT port on the switch.
3. Using a Toslink digital optical S/PDIF cable (available separately), plug one end into one of the IN ports on the switch, then plug the other end into the optical output on one of your audio source devices (e.g., DVD player, gaming console, etc.). Repeat for up to three additional audio source devices.
4. Plug the included IR Receiver into the IR jack on the switch, then position the receiver bulb where it can receive IR signals from the included IR Remote Control.
5. Plug one end of the included USB Power Cable into the USB POWER port on the splitter, then plug the other end into a USB power source, such as a computer, wall charger, etc. (available separately).
6. Press the ON/OFF button to turn the switch on. One of the LEDs will illuminate to indicate the selected input and to indicate that power is applied.
7. Plug in and power on all connected devices.
8. Start audio playback on your source devices. Use the remote control to switch between the sources and verify that you can hear audio from the output device. Alternatively, you can use the SWITCH button on the switch to cycle through the connected inputs.

LED INDICATIONS

TECHNICAL SUPPORT

Monoprice is pleased to provide free, live, online technical support to assist you with any questions you may have about installation, setup, troubleshooting, or product recommendations. If you ever need assistance with your new product, please come online to talk to one of our friendly and knowledgeable Tech Support Associates. Technical support is available through the online chat button on our website www.monoprice.com or through email by sending a message to tech@monoprice.com. Check the website for support times and links. To download the latest drivers, firmware, manuals, etc., go to www.monoprice.com and type the P/N into the search bar. If available, support files are linked at the bottom of the product page.

SPECIFICATIONS

Digital™

Output Cable Length

| up to 131 feet (40 meters) using an optical cable with loss less than 0.2dB/m
Peak Wavelength| 650nm
Maximum Baud Rate| 16Mbps
Input Power| 5 VDC (USB)
Operating Temperature| +32 ~ +104°F (0 ~ +40°C)
Operating Humidity| 5 ~ 90% RH, noncondensing

REGULATORY COMPLIANCE

Notice for FCC

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Modifying the equipment without Monoprice’s authorization may result in the equipment no longer complying with FCC requirements for Class B digital devices. In that event, your right to use the equipment may be limited by FCC regulations, and you may be required to correct any interference to radio or television communications at your own expense.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Notice for Industry Canada

This Class B digital apparatus complies with Canadian ICES-003.

• Monoprice™, Blackbird™, the Blackbird logo, and all Monoprice logos are trademarks of Monoprice Inc.
• TOSLINK® is a registered trademark of Toshiba Corporation.
• DTS®, the Symbol, and DTS and the Symbol together are registered trademarks of DTS, Inc.
• Dolby®, Dolby® Digital™, Dolby Audio™, and the double-D symbol are trademarks of Dolby Laboratories.
• Sony® is a registered trademark of Sony Corporation. PlayStation® and PS3® are registered trademarks of Sony Interactive Entertainment Inc.

FREQUENTLY ASKED QUESTIONS

What is the Monoprice 43392 Blackbird Toslink S/PDIF 4x1 Switch?

The Monoprice 43392 Blackbird Toslink S/PDIF 4x1 Switch is a device that allows you to switch between four different optical (Toslink) audio sources and output the selected source to a single audio output device.

What are the inputs and output options of the Blackbird Toslink Switch?

The switch has four Toslink (optical) input ports and one Toslink output port.

How do I switch between different audio sources using the switch?

The switch typically comes with a remote control or manual push-button operation, allowing you to select the desired audio source.

Can I connect multiple audio devices, such as a Blu-ray player, gaming console, and TV, to the Toslink switch?

Yes, you can connect up to four different audio devices with Toslink outputs to the switch and switch between them as needed.

Does the Toslink switch support Dolby Digital and DTS audio formats?

Yes, the switch should support popular audio formats like Dolby Digital and DTS, as long as your audio devices and audio output support these formats.

Can I use this switch with HDMI or other audio interfaces?

No, the Monoprice 43392 Blackbird Toslink Switch is specifically designed for Toslink (optical) audio signals and does not work with HDMI or other audio interfaces.

Does the switch require an external power source?

The switch typically requires an external power adapter to operate correctly.

What happens when multiple input sources are active simultaneously?

The switch will only output audio from the selected input source, and the other input sources will be inactive.

Can I use this switch with my home theater system to connect multiple audio devices?

Yes, the switch is suitable for home theater setups where you need to switch between multiple audio sources, such as a Blu-ray player, game console, and media player.

Does the switch support audio signals with different sampling rates?

Yes, the switch should support various audio sampling rates common to Toslink (optical) audio signals.

Can I use this switch with my soundbar to connect multiple devices?

Yes, the Toslink switch can be used with a soundbar to connect multiple audio devices.

Does the switch come with a user manual to guide the setup and operation?

Yes, the switch typically comes with a user manual that provides instructions on how to set up and use the device.

Can I use this switch with my AV receiver to expand audio input options?

Yes, the Toslink switch can be connected to an AV receiver to expand the number of Toslink audio input options.

Is the Toslink switch compatible with 5.1 or 7.1 surround sound systems?

Yes, the switch should be compatible with both 5.1 and 7.1 surround sound systems, as long as the connected devices and output support the same surround sound format.

Does the switch support lossless audio formats like FLAC?

Yes, the Toslink switch should support lossless audio formats like FLAC, as long as your audio devices and output support these formats.

DOWNLOAD THE PDF LINK:Monoprice 43392 Blackbird Toslink S-PDIF 4×1 Switch User Manual

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>