ARREGUI Class Electronic Safe with knob Instruction Manual
- June 12, 2024
- ARREGUI
Table of Contents
Class Electronic Safe with knob
Instruction Manual
CAUTION
Do not keep the keys in the safe itself.
OPENING THE SAFE
To open the safe first time, remove the small plastic cover (“B”, see diagram
- on the front panel, insert the key into the key hole and turn it counter- clockwise direction, at the same time, turn the doorknob (“A”, see diagram 1) clockwise direction to open the safe.
INSTALLING THE BATTERIES
The safe requires 4×size “AA” (1.5V) batteries.
Open the safe, push the battery cover plate “D” (see diagram 2) on the back of
the door and install the batteries. Ensuring the batteries are fitted with the
correct corresponding polarity.
Use of alkaline batteries is recommend.
PROGRAMMING THE CODE
A. With the safe door open, press the red button “C” (see diagram 2) on
the back of the door near the hinge, release it and you will hear two beep.
The yellow light will be on at the same time.
B. Now press from 3 to 8 numbers that you wish to use as a combination,
and confirm by pressing the letter “A” or “B” within 15 seconds. The safe
“bleeps” twice and the yellow light will go off, your personal code is now
set.
C. Write down your new combination immediately and check whether your new
combination has been programmed or not on conditions of the safe door open.
USING YOUR SAFE
To open the safe, enter your personal code followed by the letter “A” or “B”,
you will hear a beep and the green light will be on, then turn the doorknob in
clockwise direction to open the door within 5 seconds.
If you or an intruder uses the incorrect group of numbers, it will not open.
If the incorrect combination is used 3 times consecutively, you must wait for
20 seconds before reattempting.
If again the incorrect combination is selected 3 times, you must wait
approximately 5 minutes before reattempting access.
BATTERY REPLACEMENT WARNING
If the batteries are low, the red light (in the middle of the number panel) will warn you immediately. To test the batteries, just input your personal numbers to open the door. If the batteries are low, the red light will be on. If nothing happens, it means that the batteries are in order.
REPLACING THE BATTERIES
The safe requires 4×size “AA” (1.5V) batteries.
Open the safe, push the battery cover plate “D” (see diagram 2) on the back of
the door and replace the 4 PCS old batteries. You must reprogram the code,
using the above third step.
Use of alkaline batteries is recommended.
OVERRIDE INSTRUCTION TO OPEN THE SAFE
For your convenience, we have engineered a manual override system for your safe. If you forget or misplace your combination, remove the small central plate on the front panel ( “B”, see in diagram 1) , insert the key into the keyhole and turn it in a counter-clockwise direction, then turn the knob (“A”, see in diagram 1) in a clockwise direction towards the right. This will manually open your safe at any time.
INSTALLING THE SAFE
To reduce the risk of theft of the safe, it can be secured to floor, wall or
in a cupboard. For your convenience, there are holes (diameter 8mm) on the
back and in the bottom; therefore it can be fixed by the expansion bolts.
CAUTION: The safe should be placed horizontally when installing the safe.
Please refer to diagram 2 for reference:
MAINTENANCE
Check the condition of the battery compartment on a regular basis (every 6
months) to identify any possible signs of rust, sulphation, etc.
Grease/oil any mechanical moving parts, such as locks and bolts.
GUARANTEE CERTIFICATE
The safe is guaranteed for a period of 24 months from the date of its
purchase, as established by the Law 23/2003 dated July 10th on Guarantees in
the Sale of Consumer Goods.
ABSS accepts the responsibility for lacks of approval declared within a period
of two years in the event of any manufacturing fault which affects the
functioning of the safe from the date of its delivery, according to the law.
As from the first 12 months, the buyer must prove that the non-conformity
already existed at the moment he received the safe.
The faults produced as a result of an improper use or installation, an excess
of humidity or salinity, water or cement filtrations, force, the handling of
the devices by non-authorized persons, disasters, impacts and falls are
excluded from the guarantee.
The repair or substitution of any part due to a fault implies a 6-month
extension to the guarantee of the part repaired or substituted. ABSS will
accept the responsibility for the non-conformities that caused this repair
when the same factory faults that caused the first repair are repeated.
IDENTITY DETAILS
Name of the supplier ……………………..
Date of sale …………………………….
Name of purchaser ………………………..
Address of purchaser ………………….
IDENTIFYING DETAILS OF THE SALE
Model …………………………………………..
Series number ……………………………….
IMPORTANT:
- These details must be completed as clearly as possible and without delay by the supplier, who will stamp and sign on behalf of his company in the place indicated.
- The certificate remains in the possession of the purchaser.
- The purchaser must keep the RECEIPT for the purchase of the safe, together with the GUARANTEE CERTIFICATE to be able to accredit the date of purchase. Both documents are necessary to use the guarantee.
SUPPLIER’S STAMP
Arregui
Pol. Industrial Ubegun. 3B.
20809 Aia-Orio. Gipuzkoa
(SPAIN)
arregui@arregui.es
www.arregui.es
References
- Design of mailboxes, safes in Gipuzkoa - Arregui - Orio
- Diseño De Buzones, Cajas Fuertes en Gipuzkoa - Arregui - Orio Gipuzkoa
- Mailbox Design, casseforti in Gipuzkoa - Arregui - Orio Gipuzkoa
- Diseño De Buzones, Cajas Fuertes en Gipuzkoa - Arregui - Orio Gipuzkoa
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>