ARREGUI SUPRA Electronic Opening + Key Safe Instructions
- June 9, 2024
- ARREGUI
Table of Contents
SUPRA Electronic Opening + Key Safe
Instructions Manual
SUPRA Electronic Opening + Key Safe
Desktop safe with motorised electronic opening.
Scan the QR code to access the instructions or download them from our website.
IMPORTANT:
The first opening of the safe you must use the emergency key:
- Insert the emergency key with the red point and turn it clockwise.
NOTE: Do not store the emergency key inside the safe
BATTERY INSTALLATION
Open the door, remove the plastic cover located behind the door and place 4 new 1,5V AA batteries.
PROGRAMMING THE OPENING CODES
This safe allows to program two secret opening codes–one standard and one
master, from 3 to 6 digits each.
The initial standard code is 000000 and the initial master code is 888888. For
your security, it´s important that you change them and configure the codes you
desire.
During the process, use the button to delete the last digit entered.
Programming the standard code (the safe must be open):
A. Press 00 and the button. The screen will display SELECT.
B. Press the 0 button. The screen will display SET.
C. Enter your code (3 to 6 digits) and press the button.
The screen will display DONE.
With the door open, verify that the new code operates correctly (see section
3, opening the safe).
Programming the master code (the safe may be open or closed):
A. Press 00 and the button. The screen will display SELECT.
B. Press the 1 button. The screen will display OLD.
C. Enter the current master code (888888 the first time) and press the button.
The screen will display SET (if the code entered is incorrect, it will display
ERROR).
D. Enter the new master code (3 to 6 digits) and press the button. The screen
will display REPEAT.
E. Enter the new master code again and press the button.
The screen will display DONE (if the code entered is not the same both times,
the screen will display ERROR).
OPENING THE SAFE
Enter either of the two active opening codes and press the button. The screen
will display OPEN while the locks move, and OPENED when the door has opened,
and inside LED lamp will bright 25 seconds automatically.
If an incorrect code is entered, the screen will display ERROR1, for a second
incorrect attempt it will display ERROR2, and for a third incorrect attempt it
will display ERROR3 and the system will remain blocked for 5 minutes,
indicating by blinking HOLD 5… HOLD 4… etc. During this time, the keypad
cannot be used.
CLOSING THE SAFE
With the safe open, press the button. The screen will display CLOSE while the
locks move, and CLOSED when the door has closed.
NOTE: If the locks encounter an obstacle, they will move back and leave
the door open.
OPENING WITH THE EMERGENCY KEY
If you do not have the opening codes, or if the batteries have run out and an
external battery is not available, you can open the safe using the emergency
key.
For this, access the emergency lock. Introduce the emergency key provided with
these instructions and turn it. The safe will open.
Note: In case of an emergency opening due to a wrong code, the emergency
key opens the door but does not unblock the electronic system, you must wait
for the deadbolt time to expire.
OPENING WITH AN EXTERNAL BATTERY
If the batteries have run out, you can use the safe by placing a 9V battery in
the power supply located to the right of the keypad.
Once the safe is open, replace the batteries.
OTHER CONTROL ELEMENTS
SCREEN CONTROL: To configure the screen so it does not display the digits
that are entered, press the button and then the 3 button. If you would like
the screen to display what you enter, press the 3 button again.
SOUND CONTROL: To use the safe in silent mode, press the button and then
the 6 button. If you would like the safe to emit sounds again, press the 6
button again.
BATTERY STATUS CONTROL: If you would like to know whether the batteries
are sufficiently charged, press the button while the safe is closed. If the
batteries are fine, the screen will display HI-BAT, and if they are not, the
message will be LO-BAT. In that case, you should replace the batteries with
new ones.
In any case, if the batteries are not sufficiently charged, the system will
warn you of this when the safe is opened and closed by displaying the OPEN LO-
BAT or CLOSE LO-BAT messages on the screen, respectively.
NOTE: During the battery change process, the safe will not forget the
codes that have been entered.
MAINTENANCE
Check the condition of the battery compartment on a regular basis (every 6
months) to identify any possible signs of rust, sulphation, etc.
Grease/oil any mechanical moving parts, such as locks and bolts.
GUARANTEE CERTIFICATE
This product is guaranteed for the periods stipulated in the Law on
Guarantees. ABSS is liable for any non-conformities that may occur as a result
of a manufacturing fault that affects the performance of the product within
the legally prescribed timeframe. After this period, the consumer will have to
prove that the non-conformity already existed at the time of receiving the
product. The warranty does not cover faults caused as a result of improper use
or installation, excessive moisture or salinity, water or cement leakage,
force, unauthorised manipulation of the mechanisms, catastrophic events,
knocks or falls. The repair or replacement of any faulty part will involve an
extension of the guarantee of the repaired or replacement part, in accordance
with the provisions of the Law on Guarantees.
IDENTITY DETAILS
Name of the supplier …………………………..
Date of sale ………………………………………….
Name of purchaser ……………………………..
Address of purchaser …………………………..
IDENTIFYING DETAILS OF THE SALE
Model ……………………………………………….
Series number …………………………………..
IMPORTANT:
- These details must be completed as clearly as possible and without delay by the supplier, who will stamp and sign on behalf of his company in the place indicated.
- The certificate remains in the possession of the purchaser.
- The purchaser must keep the RECEIPT for the purchase of the safe, together with the GUARANTEE CERTIFICATE to be able to accredit the date of purchase. Both documents are necessary to use the guarantee.
SUPPLIER’S STAMP
Arregui
Pol. Industrial Ubegun. 3B.
20809 Aia-Orio. Gipuzkoa
(SPAIN)
arregui@arregui.es
www.arregui.es
Documents / Resources
|
ARREGUI SUPRA Electronic Opening + Key
Safe
[pdf] Instructions
SUPRA, Electronic Opening Key Safe, Opening Key Safe, Electronic Key Safe, Key
Safe, Safe
---|---
References
- Design of mailboxes, safes in Gipuzkoa - Arregui - Orio
- Diseño De Buzones, Cajas Fuertes en Gipuzkoa - Arregui - Orio Gipuzkoa
- Conception de boîtes aux lettres, coffres-forts à Gipuzkoa - Arregui - Orio
- Mailbox Design, casseforti in Gipuzkoa - Arregui - Orio Gipuzkoa
- Diseño De Buzones, Cajas Fuertes en Gipuzkoa - Arregui - Orio Gipuzkoa
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>