Kinderkraft Neste Up Co Sleeper Crib User Manual

Kinderkraft Neste Up Co Sleeper Crib

OVERVIEW

IMPORTANT, RETAIN FOR FUTURE REFERENCE, READ CAREFULLY

SAFETY INSTRUCTIONS AND PRECAUTIONS. WARNING:

• Do not use this product without reading the instructions for use first.
• Stop using the product as soon as the child can sit or kneel or pull himself up.
• Placing additional items in the product may cause suffocation.
• Do not place the product close to another product, which could present a danger of suffocation or strangulation, e.g. strings, blind/curtain cords, etc.
• Do not use more than one mattress in the product.
• The product should be placed on a horizontal floor.
• Young children should not be allowed to play unsupervised in the vicinity of the crib.
• The crib should be locked in the fixed position when the child is left unattended.
• All assembly fittings should always be tightened properly.
• Care should be taken that no screws are loose, because a child could trap parts of the body or clothing (e.g. strings, necklaces, ribbons for babies’ dummies, etc.), which would pose a risk of strangulation.
• Be aware of the risk of burning cigarettes, open fires and other sources of strong heat, such as electric bar fires, gas fires, etc. in the near vicinity of the crib
• Crib: maximum inclination allowed – 2 levels.
• DO NOT use crib if any parts are missing, damaged, or broken. Contact 4Kraft Sp. z o.o. for replacement parts and instructional literature if needed. DO NOT substitute parts.
• Only use the mattress sold with this crib, do not add a second mattress on this one, as suffocation hazards.
• For the bedside sleeper mode, the use of straps (8) is required. DO NOT use a bedside sleeper if any parts are missing, damaged, or broken. Contact 4Kraft sp. z o.o. for replacement parts and instructional literature if needed. DO NOT substitute parts
• The height from the floor of the adult’s bed for which the bedside sleeper is suitable can be found in picture U.
• Information on the types of adult beds for which the bedside sleeper is suitable can be found in picture U.
• The user shall not use another attachment system.
• Bedside sleepers shall never be used in an inclined position
• To prevent a suffocation hazard from entrapment, the bedside sleeper shall be properly secured to the adult bed using the attachment system.
• There shall never be a gap between the lower side of the bedside sleeper and the mattress of the adult bed.
• Check the tightness of the attachment system before each use by pulling the bedside sleeper in a direction away from the adult bed.
• If there is any gap between the bedside sleeper and the adult bed, DO NOT use the product.
• Gaps should not be filled with pillows, blankets or other items.
• DANGER! – Always completely raise the drop side when not attached to the adult’s bed
• To avoid hazards from the child’s neck being caught on the top rail on the side that is next to the adult bed, the top rail must not be higher than the adult bed mattress.
• To avoid the risk of your child being strangled the attachment system to the adult’s bed shall always be kept away from and out of the crib.

List of baby cot components – page 3

Mounting of the cot:
Prepare an appropriate surface to avoid damaging the product during assembly. Connect the side frames (1) with the main frame (3) of the cot (figure A) – you’ll hear a “click” if it’s assembled correctly (figure B). Slide the material (2) onto the exposed areas of the side frame (figure C). Place the material onto the tube of the main frame and fasten the zipper (figure C1). CAUTION! Remember to secure the zipper to prevent opening (figure D). Connect the tube of the drop-down side to the top part of the frame (figure E) and secure using the zipper on both ends (figure F). CAUTION! Remember to secure the zipper to prevent opening (figure G). Slide the ends of the side bracket (5) in the cot padding material into the relevant openings in both side frames (figure H). Next, connect the bracket to the legs of the cot by sliding it in along both sides into the relevant openings (figure H, I). You’ll hear a “click” if it’s assembled correctly. Place the cot on the side opposite the drop-down side. Slide the bar (6) into the legs and make sure that the latches on both sides are secured (figure J). Place the cot back in the vertical position. Connect the bottom bracket (4) to the legs of the cot, and slide it in along both sides until it locks – you’ll hear a distinctive “click” when this happens (figure K). Affix the bottom bracket (4) to the base of the cot using three small hook-and-loop closures (figure L). Slide the material of the cot over the bottom bracket, and affix it with a large hook- and-loop closure (figure M). Wrap the hook-and-loop closures around the brackets on the side of the cot (figure N). Place the mattress in the cot. The assembled product is shown in Figure O.

Height adjustment:
The cot is adjustable to 5 different heights. To adjust the desired height hold the cot with your foot, move button A sideways while pressing button B and adjust the frame of the cot to the desired height (fig.P).

Bedside cot:
To connect the cot to the parents’ bed, remove the safety devices at the locks (fig. R). Unlock the zips on both sides (fig. S). Slide the lever and slide out the tube of the side panel (fig. T). Repeat on the other side. Remove the side panel of the cot (fig. W) and pull the tube out of it. Adjust the height of the cot to the parents’ bed (fig. U). Fasten the buckle of the fastening straps to the cot (fig. X). Interleave the straps either through the whole bed or only through its sidebar (fig. Y)and adjust so that the cot is fixed securely to the parents’ bed (fig. Z). Roll the loose parts of the straps (9) under the cot. To move the cot as close as possible to the base of the parent’s bed, move button A sideways (fig. AA) and at the same time press button B. Move the legs to the desired distance. ATTENTION! Make sure that the straps are properly adjusted and the cot is adjacent to the mattress of the parents’ bed (fig. Z).

Locking the wheels:
The cot has 2 wheels that allow to move the cot and to connect it with the parents’ bed. To lock the wheels, press the locking button down. To unlock, move the button upwards (fig. AB).

Maintenance and cleaning

Frame – clean with a soft, clean and dry cloth.

Do not fold or store the product when it is wet and never store it in wet conditions, as it can lead to mold growth.
International: support@kinderkraft.com. (0048) 61 646 02 37

• kinderkraft.com.
• kinderkraftofficial
• kinderkraft
• kinderkraftofficial

All rights to this data are entirely reserved to 4Kraft Sp. z o.o. Any unauthorized use or misuse, including usufruct, copying, duplication and sharing, wholly or partially, without consent of 4Kraft Sp. z o.o. may result in legal consequences.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>