Blonbar AJ100B Flame Speaker Instruction Manual
- June 12, 2024
- Blonbar
Table of Contents
Blonbar AJ100B Flame Speaker
Please read carefully before use
Product Introduction
- Button operation, convenient and quick
- Flame light function
- Night light function
- Wireless speaker function Support multiple speaker connections (one drag multi-function, one host with multiple slaves, immersive experience)
- Built-in high-capacity rechargeable lithium battery, more convenient for outdoor use
- IP65 dustproof and waterproof.
Technical Parameters
Wireless version
| V5.0| Distortion Rate|
≤10%
---|---|---|---
Searching Name
| Searching Name| Output Power| 10W
Transmission Distance| ≥1om| SNR|
80dB
Frequency Response
| 50Hz-20kHz| Horn Parameters| <1>52mm 4Ω10W
The Charging Interface| Type-C| Power Supply|
5V 1A
Built-in Lithium Battery
| 3.7V/2000mAh| Product Size|
113x113x188mm
Flame Lamp mode
Flame lamp and speaker are independently designed and controlled. Short press
the light key” ” for the first time, and the flame light will turn on. Short
press the light key” ” for the second time to turn on the night light, and
long press the light key
” ” to adjust the brightness or darkness of the night light. Short press the
light key” “for the third time, the night light goes out, and the cycle
repeats in sequence.
Introduction to key functions
Power switch, play/pause button:
-
Long press this button for 3 seconds to turn on or turn off the
Wireless speaker, and the blue LED light is flashing when the
Wireless speaker is turned on. -
The blue light is steady on when the Wireless speaker connection is successful;
-
Short press this button to play/pause function;
-
When using Wireless speaker mode and pair multiple mode, the function of this key on the host is normal;
Pair key:
When the Wireless speaker is turned on, press this button shortly to enter the Pair key, and the green LED light is flashing, waiting for the connection with the host. After the connection is successful, the green LED light will be on for long time, and only the secondary machine will be on for long time with single green light, the main machine will be on for long time with blue light.
Previous song/VOL- key:
In Wireless speaker mode, short press is the previous song; long press is to reduce the volume; in pair multiple mode, this key has no function;
Next song/VOL+ key:
In Wireless speaker mode, short press is the next song; long press is to increase the volume; in pair multiple mode, this key has no function; (when the volume is adjusted to the maximum, there will be a beep sound).
How to use one support, multiple main and auxiliary units, and multiple
speakers:
In Wireless mode, first connect the speaker to the mobile phone and pair it successfully. This speaker is used as the host. Press the host Pair key and accompanied by prompt sound, and then open other auxiliary speakers, and then short press each auxiliary Pair key is accompanied by a prompt tone. After the secondary machines are paired with the host one by one, a prompt tone is played when the secondary machines are successfully connected. After all secondary machines are successfully connected, the indicator lights are green and on.
Note: Shut down the host directly, and shut down all the auxiliary
machines together. Please do not press the pairing button when you buy only 1
speaker. Otherwise, when the speaker enter pairing mode, it will not be able
to connect to the Bluetooth of the mobile phone.
How to connect multi-speakers? Please scan this QR code.
Charging instructions
Power input
Plug the TYPE-C cable into the USB port on the bottom back of the speaker fot charging, the red light will be on when charging, and it will go out when fully charged.
Attention
- Please charge in 0°C-40°C environment.
- Not recommended to use while charging.
- Please unplug the charging cable in time after fully charged.
- Do not charge the speaker in a humid environment
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>