Schreder BRITELINE GEN2 1 Versatile and Efficient Lighting Instruction Manual
- June 12, 2024
- Schreder
Table of Contents
BRITELINE
GEN2 1
External version
INSTALLATION INSTRUCTIONS
BRITELINE GEN2 1 Versatile and Efficient Lighting
PRODUCT OVERVIEW
| BRITELINE GEN2 1 | EXTERNAL GEAR BOX |
|---|---|
| A | B |
609mm
23.97in| 332mm
13.07in| 436mm
17.16in| 16.5kg
36.371bs| 416mm
16.37in| 372mm
14.64in| 221mm
8.7in| 205mm
8.07in| 121mm
4.76in| 6.2kg
13.6lbs
EPA – Effective Projected Area
| a = 0°| a = 30°| a = 45°| a = 70°| a = 90°
---|---|---|---|---|---
S(m²)| CxS
(m²)| EPA
(ft²)| S(m²)| CxS
(m²)| EPA (ft²)| S(m²)| CxS
(m²)| EPA
(ft²)| S(m²)| CxS
(m²)| EPA (ft²)| S(m²)| CxS
(m²)| EPA
(ft²)
S1| 0.057| 0.07| 0.74| 0.0951| 0.12| 1.23| 0.1100| 0.14| 1.43| 0.1339| 0.17|
1.73| 0.1406| 0.17| 1.82
S2| 0.1406| 0.17| 2.| 0.1382| 0.17| 1.79| 0.1258| 0.16| 1.63| 0.0920| 0.12|
1.19| 0.0570| 0.07| 0.74
S3| 0.0355| 0.05| 0.46| 0.0355| 0.05| 0.46| 0.0355| 0.05| 0.46| 0.0355| 0.05|
0.46| 0.0355| 0.05| 0.46
MOUNTING
Screws and washers are
not included in the package! Minimum screw requirement:
| Vibration standard | IEC 0.5g / ANSI 1.5g |
|---|---|
| Minimum fastener requirement | 1x M20 8.8 or A2-70 |
DIN9021 large plain washer
Tightening torques| 1xM20: 200 Nm
2xM20: 140 Nm
Recommended to use anti-seizing agent (Tikal Tef-Gel®) !
| 1. 1xM20 with extra large washer
or
2. 2xM20 with extra large washer
---|---
Mounting dimensions
| D1 | D2 | D3 | D4 | D5 |
|---|
min 250mm
min 9.84in| 70mm
2.75in| 150mm
5.9in| 320mm
12,6in| 460mm
15.98in
Minimum Surface Contact Area for screw fixation
Fasteners are not
included in the package!
Remark: the hatched area always need to be supported by a flat planar mounting
surface as minimum.
Wider surface contact is recommended, smaller is not allowed!
ANGLE ADJUSTMENT
-
Loosen the clamp screws
-
Adjust tilting angle
Separate scale for adjusting the distance of the optical block from the luminaire holder
The swing arm inclination is adjustablein 10 degree increments
relative to fork base.
ALLOWED tilt angle is between -10° to 90° -
Tighten the clamp screws
Do not exceed the proposed torque levels, as it may result in fraction of the parts!
ALLOWED POSITIONING
GEAR INSTALLATION
SAFETY CABLE
Steel safety cable should pass through the holes shown in the drawing in
sequence.
Then connect the two ends with the lock and tighten the lock screw by hand.
For installations over 3m height: secondary safety system application is
mandatory, which is appropriated for the luminaire load (e.g. safety cable)
1500mm/59.05in safety cable is supplied with the luminaire.
ELECTRICAL CONNECTION
-
Remove the R-type buckles from the junction box and gear box
-
Open junction box and gear box
Cable ID| Connection| Cable gland| Suitable cable Ø
---|---|---|---
A| Mains input| M20| Ø6-10mm or
Ø10-14mm
B| Mains re-launch
C| DC output to optical block| M25/cable ptorection
compatibility| Ø6-10mm or
Ø10-14mm
D| Dimming input| M16| Ø4.5-7.5mm or
Ø7.5-10.5mm
E| Dimming re-launch -
Cable types and cable gland
When using a larger external diameter cable, the plug and the smaller inner diameter seal need to be removed
When using a smaller external diameter cable, simply remove the plug
-
Make electrical connection
Wiring should strictly follow the marking label instruction, otherwise the product could be damaged or the functions could be affected.
-
Close junction box and gear box
Close the cover of the junction box and gear box, and put the R-type buckles back on both.
RECOMMENDATIONS
- Surrounding distances
At least 1 meter distance should be kept from surrounding walls, floor, and ceiling for all types of mounting/inclination. - Maximum number of luminaires per MCB
Product| Driver| MCB B type
---|---|---
B10| B13| B16| B20| B25| B32| B40
BRITELINE GEN2 1 ©220V| EUM-680MG/BG| 1| 2| 2| 3| 4| 5| 6
BRITELINE GEN2 1 ©480V| ESM-680MG/BG| 2| 2| 3| 4| 5| 6| 7
Product| Driver| MCB C type
C10| 13| 16| C20| C25| C32| C40
BRITELINE GEN2 1 ©220V| EUM-680MG/BG| 1| 2| 3| 3| 4| 5| 6
BRITELINE GEN2 1 ©480V| ESM-680MG/BG| 3| 4| 5| 7| 9| 11| 14
AIMING DEVICE
The small blocks on the side of the optical block assure the installation of
the built-in aiming devide.
The external aiming device position 1 needs to be aligned with positions
2 and 3
ACCESSORIES – HOOD
SAFETY INSTRUCTIONS
The light source contained in this luminaire shall only be replaced by the
manufacturer or his service agent or a similar qualified person. Always switch
off the power prior to installation, maintenance or repair activities.
RISK GROUP 2 – CAUTION! Hazardous optical radiation may be emitted from
this product. Do not stare at the luminaire when operating as it may be
harmful to the eyes. The luminaire should be positioned so that prolonged
staring at the luminaire at a distance of less than 0.2m is not expected.
This product contains a light source of an energy efficiency class G or
higher.
In case of PVC insulated mains cable, the installer MUST ensure that the WHOLE
cable is protected against climatic conditions, especially UV rays and rain,
by making sure that the cable is contained inside the luminaire and pole
Y-connection: In case of damage to the wire, it has to be replaced only by the
manufacturer, distributor or by an expert, to avoid risks.
www.schreder.com
Rev B | 07-2023
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>