SEAJIC AB216 Vlogging Tripod User Manual
- June 12, 2024
- SEAJIC
Table of Contents
SEAJIC AB216 Vlogging Tripod User Manual
Product Introduction
Release Tripod
Step 1 : Press the triangle button on the bottom of the tripod to release tripod legs.
Step 2: Hold the handle sleeve with one hand and the pull handle of the
phone holder with the other hand to pull out the telescopic rod. Adjust to
desired height. Tripod legs will open automatically as the telescopic rod
being pulled out.
Fold Tripod
Hold the handle sleeve with one hand and push the telescopic rod back in.
Attention
• Do not pull legs to open tripod. • Push the handle sleeve all the way down
so that the tripod legs are fully opened and stable.
Detach/Attach Remote Controller & Charging
Detach Remote Controller:
Type C
When Battery is low , detach the remote controller and charge with the type c USB include in the package
Attach Remote Controller:
The remote control is equipped with a magnetic attraction feature. To remove it from the slot, simply pull it outwards. To reinsert it, align it with the slot and it will automatically be attached Type-C When battery is low, detach the remote controller and charge with the Type-C USB included in the package.
Switch between landscape & portrait
Landscape
**Portrait Screen
**
Adjust the pan tilt locking knob to keep the mobile phone holder locked in any direction
- The product comes with the patented slide rail and the rotating shaft holder. You can also switch freely between landscape and portrait screen without taking out the phone.
- Pull outward to open the secondary arm and increase the bearing and stability of the product.
- Adjust the pan-tilt locking knob to keep the mobile phone holder locked in any direction.
Adjust The Control Handle
twist clockwise to tighten it twist anticlockwise to release it
As shown above, adjust the rotating ball head to the required angle by locking and releasing, and then lock the handle to freely shoot any angle. Description of Cold shoe slot
**Description of Cold Slot
**
This product is equipped with three cold shoe slots, which are compatible with a fill light or other photography accessories.
Connect Bluetooth
Long press the shutter/power button on the remote controller for 3 seconds until the green light flashes. On your device, go to Settings > Bluetooth and turn on Bluetooth. Find” SEAJIC “to connect. When pairing is completed, the green light will be on constantly.Short press the shutter/power button to take pictures when the connected smartphone is in camera mode. Long press for 3 seconds again to turn off the Bluetooth.
Specification
| Product model | Oth-AB216 |
|---|---|
| Product size | 1.8×2.4×10.4in |
| Product weight | 356g (±10g) |
| Battery capacity | 50mAh |
| Unfolded length | 46in (±0.4in) |
| Product material | Aluminum ABS+PC |
FCC Caution
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
Note:
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and. if not installed and used in accordance with the
instructions. may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on. the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radioTIV technician for help.
The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.
IC Caution:
This device complies with Industry Canada’s licence-exempt RSSs. Operation is subjectto the following two conditions:
- This device may not cause interference; and
- This device must accept any Interference, including Interference that may cause undesired operation ofthe device.
The device has been evaluated to meet general RF exposure requirement.
The device can be used in portable exposure condition without restriction.
Web:www.osmdigi.com
Standard: Q/OSL 001-2019
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>