Karbeen KL Series Cub Fireproof Safe Box Instruction Manual
- June 15, 2024
- Karbeen
Table of Contents
Karbeen KL Series Cub Fireproof Safe Box
After-sales Email: aaasafe-service@outlook.com
Warning
- Do not lock the emergency key or emergency battery box into your safe.
- lf the safe box is not used for a long time, the battery should be removed to prevent leakage of liquid from damaging the electronic system.
- Purchase 4 AA batteries in advance, this safe does not contain batteries.
IMPORTANT
If you experience any problems or challenges with your safe, please contact
us. Many issues can be resolved quickly without the product being returned.
After-sales Email: aaasafe-service@outlook.com
BOX CONTENTS
- Knob
- Emergency Key Cover
- Yellow Light (Digital Indicator Light)
- Red Light (Low Battery Reminder）
- Green Light
- Emergency Power Jack
- Confirming Button
- Bolts
- Battery Compartment
- Setting Button
- LED Light
- Emergency Keys*2
- Expansion Screws*4
- Emergency Battery Box
- Instruction Manual
NOTICE: Please don’t put the emergency keys and the emergency battery box inside the safe.
SET UP THE CODE
Step 1：Open the door with the key
- Find the emergency keys in the accessories bag.
- Left slide the emergency lock cover.
- Insert the emergency key, turn it counter-clockwise to the limit and hold it, turn the knob clockwise at the same time to open the door.
NOTICE: Finish operation, pull out the emergency key and keep it in a safe place.
Step 2：Install Battery
- After first opening, keep the safe open and locate the battery case; prepare 4 brand-new AA 1.5 Volt alkaline batteries (not included);
- Remove the internal battery case cover and install the 4 AA batteries by matching the + & – electrode;
NOTICE:
- Rechargeable battery is not recommended as it may destroy the internal electronic components of your safe.
- Please use brand-new batteries, do not mix used batteries with new batteries.
- Under normal condition, if the red lights is on it means the voltage is low and you should insert new batteries.
Step3: Set up the first code
- Keep the door opened, press the setting button for 1 second, the yellow light flash twice and then start setting code.
- Input the new user code(3 to 8 digits) and press the # to confirm. it will be confirmed by 2 buzzer beeps, successful setting.
- If the yellow light flashes with 3 buzzer beeps which means the code changing is not effective,and you need to try again.
Step4: Set up the second code
- Keep the door opened, press 0 twice and then press the setting button for 1 second, the yellow light flash twice and then start setting code.
- Input the new user code(3 to 8 digits),and press the # to confirm, it will be confirmed by 2 buzzer beeps, successful setting.
- If the yellow light flashes with 3 buzzer beeps which means the code changing is not effective and you need to try again.
NOTICE: The initial code is 159, need to be modified.
OPEN / CLOSE THE DOOR
THREE WAYS TO OPEN THE DOOR
The first way to open: Use the emergency key.
Slide left the emergency lock cover. Insert the emergency key, turn it counter-clockwise to the limit and hold it, turn the knob clockwise at the same time to open the door. (Suitable for the first opening, forget code, or weak battery).
The second way to open: Use the code.
Input your code(3 to 8 digits) and press # to confirm, the green light will be on. Rotate the knob clockwise and open the door within 5 seconds. (Suitable for quick access and daily use).
The third way to open: Use the emergency battery box + code.
When the battery of your safe is weak and can’t find the keys, please insert 4 AA batteries in the emergency battery box, plug the emergency power cord into the emergency power jack, then enter the correct code to open the door.(Suitable for the battery is out of power and the key can not be found).
CLOSE THE DOOR
Close the door and rotate the knob counterclockwise.
ADDITIONAL FEATURES
ANTI-THEFT LOCKING SYSTEM
- If you enter incorrect code for three consecutive times, the system will be locked for 20 seconds and a beep warning sound will be heard.
- If you enter incorrect code for three consecutive times again, the system will be locked for five minutes and a beep warning sound will be heard.
NOTICE: The keypad would be disabled during the beeping. You can only opening the safe with emergency key and power-cut by removing the batteries to stop the locking state and the beeps. (In this case, the system is restored to factory settings and all code are reset. The initial code is 159. You need to set a new code.)
MUTE FUNCTION
- In standby state, press then press * 633, the mute function is tuned on;
- In standby state, press then press * 66, the mute function is tuned off.
UNDER VOLTAGE WARNING
When the voltage is around 4.8V, after unlocking with the code, both red and
green lights come on, reminding the user that the battery power is low and the
user needs to replace the batteries.
BOLTING DOWN YOUR SAFE
TOOLS NEEDED TO BOLT SAFE
- Drill (not included)
- Marker pen (not included)
- Expansion screws (included)
MOUNT THE SAFE
Step1:
Place the safe at the installation place (wall or floor), mark the drilling
spots on the wall/floor from the inside pre-drilled holes.
NOTICE: Different sizes have different number of pre-drilled holes,
please refer to the actual safe box.
Step2:
Remove the safe and drill a about 10 mm hole in the wall or floor with drill
bit.
Step3:
Position safe in place and install screws through safe in to the holes.
Tighten screws.
TROUBLESHOOTING
| Malfunction | Cause | Solution |
|---|---|---|
| Inserting the battery does not work | Battery drained | Replacement battery |
| Electrode reversed | Put the battery in the correct position | |
| Can’t open with code | Low battery | Replace with new battery |
| Wrong code | Please reset your code | |
| Door won’t close | There is an obstacle in the middle of the latch or behind | |
| the door | Close the door after clearing the obstacle | |
| Door won’t open | The key is not turned to the specified position | After |
turning the key to the specified position, turn the knob to open
The knob is not turned within 5 seconds of entering the code| After turning
the key to the specified position, turn the knob to open
Cannot be locked| Key not pulled out| Lock the door after removing the key
LED won’t light up| Use the key to open the safe| Use the electronic code to
open the safe
If you cannot handle the above problems properly, please feel free to contact
our after-sales team, we will do our best to help you solve all your problems
We provide 7×24 hours after-sales service, please feel free to contact our
after-sales email
Maintenance
- If you do not use the safe for a long time, please take out the battery in the safe to prevent the battery fluid from leaking and damaging the safe.
- Keep your keys and emergency battery box safe, it can open the the safe when the safe is out of power or if you forget your code.
- Store the safe in a cool, backlit place.
- Do not wipe the safe with corrosive chemical solvents, use a clean rag to wipe with a little cleaning agent.
CUSTOMER SERVICE & WARRANTY
We feel confident that you will love our safe box. If there’s something makes
you unsatisfied, please don’t hesitate to contact us. Many issues can be
quickly resolved without the product being returned.
After-sales Email：aaasafe-service@outlook.com
LIFETIME KEY SERVICE: We offer 1 year warranty service and lifetime key
service. If your key is lost or damaged, please provide your order ID,
shipping address and the serial number on the lock cylinder of the safe, via
After-sales Email, we will give you the most satisfactory reply within 24
hours.
NOTICE: If the key is lost or damaged due to personal reasons, we will
bear the cost of the replacement key, but you need take charge the cost of
shipping. Thanks for your understanding.
LINKED WARRANTY (TERMS AND CONDITIONS)
We committed to building high quality products and will make every effort to
ensure our products are free from any defects. We guarantee your safe will be
free of defects in materials or workmanship for a period of one year from the
date of original. This warranty does not cover abuse, misuse, use in any
manner for which is not designed, neglect, modification, damage in advertently
caused by the owner, accidents or tampering. If you safe is determined to be
defective and we are responsible for the cause we will have it repaired at our
expense,or we will send a new replacement at no cost to you.You will be
required to return your existing unit as well as all included accessories to
us to replace the defective unit. If it is determined your safe needs to be
returned our customer support team will provide you with a return detail.
Please have the following information available when contacting us:
- Purchaser’s name and mailing address, email address, and phone number;
- Online order number;
- Detailed description of problem.
Thank you for your time to read.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>