ARCORA AR7102401 Stainless Steel High Arc Kitchen Faucet Installation Guide
- June 12, 2024
- ARCORA
Table of Contents
ARCORA AR7102401 Stainless Steel High Arc Kitchen Faucet
Product Information
The product is a faucet that is designed for easy installation and has a durable finish. It complies with California water efficiency regulations, California Proposition 65, and the Federal Safe Drinking Water Act. The faucet has a water flow rate of 1.8 gallons per minute (6.8 liters per minute) and comes with a screened washer pre-installed in the conical nut. The maximum deck thickness for installation is 2 inches (50mm), and it has a standard 3/8 inch pipe connection with a G1/2 adapter included. The product is available in both single-hole and 3-hole configurations.
Product Usage Instructions
- Before beginning installation, read all instructions and warnings thoroughly.
- Clean the water pipe thoroughly to remove any dirt or deposits.
- Remove the brass lock nut, washer, and washer from the thread rod counter-clockwise.
- Attach the O-ring to the faucet body.
- If the sink is uneven, use silicone under the gasket for a secure fit.
- Fasten the thread pipe to the base of the faucet body clockwise.
- Slide the tubes down through the mounting hole and place the faucet on the sink.
- If the sink is uneven, use silicone under the gasket for a secure fit.
- Apply Teflon tape to the quick connect installation, if necessary.
- Use the triangle fastener when the thickness of the sink requires it.
Installation instructions
You may need
For easy installation of your faucet you will need:
- To READ ALL the instructions completely before beginning.
- To READ ALL warnings, care, and maintenance information.
Cleaning and Care
Care should be given to the cleaning of this product. Although its finish is
extremely durable, It can be damaged by harsh abrasives or polish. To clean,
simply wipe gently with a damp cloth and blot dry with a soft towel.
With 1.8 gpm are compliant with California water effi ciency
regulations,Complies \with California Proposition 65 and with the Federal Safe
Drinking Water Act.
Water Use Information
1.8 gpm 6.8L/min, You can choose to replace the current limiting device and face the water pipe square.
Before installing the valves, clean the water pipe thoroughly to avoid dirt and deposits.
-
Remove the brass lock nut (6) from the thread rod counter-clockwise, remove the washer (5) and washer (3)
-
Make sure fasten the thread pipe(3) to the base of the faucet body clock-wise.
-
1. Make sure attach the O-ring(2) to the faucet body.
2. Slide tubes down through mounting hole andfaucet on sink.
Option : If sink is uneven, use silicone under the gasket.- Make sure attach the O-ring(2) to the faucet body.
- Slide 9.6″decorated plate with gasket(3) up over tubes and mounting stud.
Slide tubes down through mounting hole and faucet, 9.6″decorated plate with gasket on sink.
-
Use the triangle fastener(15) when the thickness of sink <5mm.
Place Triangle fastener(15) and washer(4) and metal plate(5) over mounting stud(3) under sink. Secure with mounting nut(6), tighten the screws(7) to fix the faucet body
- Attach pull-out hose (11) on quick connects (9). Press the quick connects firmly.
- Attach weight ball(16) to pull-out hose (11) Make sure the pull-out hose is not blocking by other objects and not touching the ground. The appropriate height for gravity ball installation is 100mm.
- Attach supply hot(8)and cool lines(9) .
- If the anglve is G1/2”, please use G3/8” standard pipe connection G1/2” adapter included (12) . Do not overtighten. Turn water back on.
Check for Leaks
Turn on water and check all connections at arrows for leaks. Refer back to the
appropriate installation instructions and retighten if necessary.
The sprayer can be removed by pulling directly out from the spout.
- water flow pattern unchanged when the water is turned off.