VISUAL COMFORT KW2722 Stretto 28 Inch Sconce Instruction Manual
- June 12, 2024
- VISUAL COMFORT
Table of Contents
VISUAL COMFORT KW2722 Stretto 28 Inch Sconce
Product Information
Product Name: Stretto 28 Sconce
Item Number: KW2722
Installation Requirements: This light fixture should be installed in accordance with all applicable, local installation codes, and by a person familiar with the construction and operation of it, as well as the hazards involved.
Product Care Instructions: Clean only with a soft dry cloth or feather duster. Do not use abrasive or chemical agents.
Product Usage Instructions
- Tools Required (Not Included): Phillips Screwdriver, Hammer, Slotted Screwdriver, Drill, Pencil
- Remove all parts from the box and place them on a clean, soft surface.
- Detach the mounting plate (B) from the fixture body (E) by removing screws (F).
- Using the mounting plate (B) as a guide, align it with the junction box and mark the anchor positions.
- Drill holes in the marked positions with a drill bit slightly smaller than the anchor size.
- Install anchors (A) into the drilled holes using a hammer.
- Attach the mounting plate (B) to the junction box using mounting screws (D), then secure wood screws (C) to anchors (A).
- Thread the support cable through the hole on the back of the mounting plate (B).
- Ensure all wire connections are tight and carefully tuck them into the junction box.
- Install the fixture body (E) onto the mounting plate (B) and secure it with screws (F).
- For outdoor/wet location installation, apply a small bead of silicon compound where the backplate meets the wall to prevent water from entering. Note: Large gaps will need to be correctedbefore applying the silicon compound.
NOTICE
This light fixture should be installed in accordance with all applicable, local installation codes, and by a person familiar with the construction and operation of it, as well as the hazards involved. Inspect item and contents carefully. If any damage or defect is found, do not install. Retain all packaging material until installation is complete and approved.
TOOLS REQUIRED
(NOT INCLUDED):
- Phillips Screwdriver
- Hammer
- Slotted Screwdriver
- Pencil
- Drill
ASSEMBLY INSTRUCTIONS
-
Carefully remove all parts from the box. Place on a clean, soft surface.
-
Remove mounting plate (B) from fixture body (E) by removing screws (F).
-
Using the mounting plate (B) as a guide, line up with the junction box and mark anchor positions.
-
Using a drill bit slightly smaller than the anchor, drill holes in the marked positions. Install anchors (A) into the holes using hammer.
-
Install mounting plate (B) to junction box and secure with mounting screws (D), then secure wood screws (C) to anchors (A).
-
Run support cable through hole on back of mounting plate (B). Wrap the support cable around the saddle (a), and secure with u- bolt (b) and hex nuts (c). (See diagram 1)
-
Wrap fixture ground wire (green) around the green grounding screw (see diagram 2). Tighten. Continue fixture ground wire and connect to supply ground wire (usually green or bare copper) using wire nut (G).
NOTE: It is imperative that the fixture is grounded. -
Connect fixture neutral wire (white) to the supply neutral wire (usually white) using wire nut (G).
-
Connect fixture hot wire (black) to the supply hot wire (usually black) using wire nut (G).
CAUTION: Do not reverse the hot and neutral connections.
NOTICE:
This light fixture should be installed in accordance with all applicable, local installation codes, and by a person familiar with the construction and operation of it, as well as the hazards involved. Inspect item and contents carefully. If any damage or defect is found, do not install. Retain all packaging material until installation is complete and approved. -
Make sure all wire connections are tight, then carefully tuck into the junction box.
-
Install fixture body (E) to mounting plate (B) and secure with screws (F).
FOR OUTDOOR/WET LOCATION INSTALLATION: -
Using silicon compound, apply a small bead where backplate meets the wall to prevent water from entering.
NOTE: Large gaps will need to be corrected before applying silicon compound.
Care Instructions: Clean only with a soft dry cloth or feather duster. Do
not use abrasive or chemical agents.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>