LILLIPUT A13 3 Inch 4K OLED Broadcast Monitor User Guide
- June 2, 2024
- LILLIPUT
Table of Contents
LILLIPUT A13 3 Inch 4K OLED Broadcast Monitor
Product Usage Instructions
- Do not place the display screen towards the ground.
- Avoid heavy impact or dropping onto the ground.
- Do not use chemical solutions to clean the product; wipe with a clean soft cloth instead.
- Do not block any vent holes.
- Follow instructions and troubleshooting guidelines for adjustments.
- Unplug the power and remove the battery during long-term non-use or thunder weather.
FAQ
Q: Can I use chemical solutions to clean the product?
A: No, please use a clean soft cloth to maintain the brightness of the surface.
Q: How do I adjust the display settings?
A: Press the MENU button to access the OSD menu and navigate through options using the / buttons. Use the buttons to adjust values.
Important Safety Instructions
- Please read User Guide before using this product.
- Please keep User Guide for future reference.
- Please read the precaution to prevent possible danger and loss of property.
Precaution
- Please do not place the display screen towards the ground.
- Please avoid heavy impact or drop onto the ground.
- Please do not use chemical solutions to clean this product. Please wipe with a clean soft cloth to maintain the brightness of the surface.
- Please do not block any vent holes.
- Please fol low the instructions and trouble shootings to adjust the product. Other improper adjustment may result in damage. Any further adjustment must be performed or conducted by a qualified technician.
- Please unplug the power and remove the battery if long term no use, or thunder weather.
Production Description
-
Power Button
-
Input Button
Press to switch the signal source -
MENU
Press to enter the menu.
Press to enter the option in the menu. - < > button Select the option in the menu. Adjust the option value. Before entering the menu, single press to activate the function bar, and press again to switch between volume, brightness, contrast, saturation, hue, sharpness and backlight
-
Exit ButtonExit Button
-
Fn User definable buttons User definable buttons
Default option
Default option: DisplaDisplay Modey Mode(Long press Fn button for 3Long press Fn button for 3–5 seconds to custom options.5 seconds to custom options. -
SDI Input & OutputSDI Input & Output
-
HDMI Input port HDMI Input port
-
DP Input port DP Input port
-
Earphone jack earphone jack
-
12V DC Power port12V DC Power port
Menu Setting
- Before setting the functions, please make sure the device is connected correctly.
Shortcut keys
FN Button
- Long press FN button for 3-5 seconds to pop up the shortcut menu on the screen. The default option will be highlighted as white. The option selected will be highlighted in yellow. The unavailable option will be highlighted as grey.
- Select the option via the”◄ / ►” buttons. Then press the “MENU” button to confirm and set the default option.
- Shortcut functions can be customized to meet user’s needs as follows:
FN Shortcut function Menu
Center Marker| Check Field| False Color
Safety Marker| Freeze| Display Mode
Aspect Marker| Pixel to Pixel| Disp Rotate
Aspect| Color Space| Disp Mirror
Underscan| Peaking|
Function Menu
-
Under the non-menu screen, press the”◄ / ►” buttons to activate the function bar, and then press the “MENU” button can activate the shortcut menu bar to select the function from Volume, Brightness, Contrast, Saturation, Hue, Sharpness, Volume, Backlight.
-
Use the < or > button to adjust the value.
-
Default function is [Volume]
MENU Operations
- When power on, press the “MENU” button on the device, and the OSD menu will display on the screen .
- Press ◄ / ► ” button to choose sub-menu or adjust the values ;
- Then press the “MENU” button to confirm;
- Press the “EXIT” button to return / exit menu.
PICTURE
Picture | Brightness | 0~100 |
---|---|---|
Contrast | 0~100 | |
Color space | Native, DCIP-3, Rec.709 | |
Saturation | 0~100 | |
Hue | 0~100 | |
Sharpness | 0~4 | |
Temperature | 9300/7500/6500/5800/User | |
Red Gain | 0~256 | **** |
(Note: Available only under “User” mode)
Green Gain| 0~256
Blue Gain| 0~256
Back Light
| ****
0~100
HDR| On, OFF
Brightness
- Control the degree of brightness between 0-100.
Contrast
- Control contrast ratio between 0-100.
Color Space
- Select the display gamut from among [Native], DCIP 3
Note
Saturation and Hue are only available under Native mode.
Saturation
- Adjust the color intensity between 0-100.
Hue
- Adjust hue between 0-100.
Sharpness
- Control sharpness of the image between 0 and 4. The default value is 2.
Color Temp.
- Use this item to choose one of the colour temperature presets: [5800K], [6500K], [7500K], [9300K] and [User], the default value
Note
Onl y available under [User] mode to adjust R/G/B Gain.
R/G/B Gain
- Adjust the R/G/B Gain of the current Color Temperature from 0 to 255. Default value: 128.
Back Light
- Adjust the level of the backlight from 0 to 100.
HDR
- Use this item to activate or deactiv ate HDR function.
FUNCTION
**** Function | Center Marker | OFF/ ON |
---|---|---|
Safety Marker | OFF, 95%, 93%, 90%, 88%, 85%, 80% | |
Aspect Marker | OFF, Full, 17:9, 16:9, 4:3, 1.85:1, 2.35:1 | |
Aspect | Full, 17:9, 16:9, 4:3, 1.85:1, 2.35:1 | |
Underscan | OFF/ ON | |
Pixel to Pixel | OFF/ ON | |
Check Field | Off, Red, Green, Blue | |
Freeze | OFF/ ON | |
Peaking | OFF/ ON | |
False Color | OFF/ ON |
Center Marker
- Select [On] to display the centre marker “+” and [Off] not to display it.
Safety Marker
- Select [Off] not to display the safety marker. O r select the size of the safety markers: [95%], [93%], [90%], [88%], [85%],
Note
When this item is used with the aspect marker, it is only inside the aspect
marker.
Aspect Marker
- Select the aspect ratio of the marker: [Off], [Full], [17:9], [16:9], [4 :3], [1.85:1], [2.35:1].
Aspect
- Switch aspect ratio setting among from [Full], [17:9], [16:9], [4:3], [1.85:1], [2.35:1].
Underscan
- If the image shows a size error, use this setting to zoom in/out pictures automatically when receiving signals.
Pixel to Pixel
- Display the original pixels of the image one by one.
Check Field
- Select one of the check field modes: [Off], [Red], [Green], [Blue].
Freeze
- Choose [On] to capture one frame of the current image on the screen, and choose [Off] to close the freeze function.
Peaking
- The peaking is used to aid the camera operator in obtaining the sharpest possible picture. Select “On” to display coloured outlines around sharp areas of the image.
False Color
- Use this item to activate or deactivate the false colour function.
Display Mode
Display Mode
| ****
1P, 2P LR, 2P TB, 2P PIP, 4P
---|---
Multi-picture mode: There are 5 picture modes optional: 1P (single picture), 2P LR (dual picture/ left and right), 2P TB (dual picture/ top and bottom), 2P PIP (picture in picture), 4P (quad Picture)
Note: This function can work with the “Select Region” function to meet the user’s requirement.
Display Setting
Display Setting
| Disp Rotate| 0°, 90°, 180°, 270°| Available when a single display
---|---|---|---
Disp Mirror| OFF, L/R, U/D| Available when a single display
LR Ratio| 0-4| Available in 2P LR mode
PIP Position
| Top Left, Top Right,
Bottom Left, Bottom Right
| ****
Available in PIP mode
PIP Transparency| 0-10
PIP Size| 0-10
Input Swap
| ****
/
| Available in PIP, 2P LR and 2P
TB mode
Display Rotate
- This setting supports flipping the image to 0°, 90°, 180°, and 270° modes.
Display mirror
- This setting displays two different input signals to Light/Right or Up/Down, the user can choose it to view the images according to the requirement.
LR Ratio
- When the Display mode is 2P LR, the ratio of the left and right images can be adjusted from 0 to 4.
PIP Position
- The position of the sub-picture can be adjusted when the display mode is PIP. Option: Top Left, Top Right, Bottom Left, Bottom Right.
PIP Transparency
- When the display mode is PIP, the transparency of sub picture can be adjusted from 0 to 10.
PIP Size
When the display mode is PIP, the size of sub picture can be adjusted from 0
to 10.
Input Swap
- When the display mode is PIP, 2P LR and 2P TB, the two pictures on the screen can be swapped.
Select Region
**** Select Region
| 1P| Unavailable
---|---|---
2P LR| Left Side, Right Side, Full
2P TB| Top Side, Bottom Side, Full
2P PIP| Main, Sub, Full
4P| 1P In、2P In、3P In、4P In(Adjust region1/2/3/4 individually. ) 1P Out、2P
Out、3P Out、4P Out(Adjust the other 3 regions except region1/2/3/4)
4P full (Adjust full screen)
Region
The image and function parameters of the selected region can be adjusted
individually. All regions can be adjusted in full-screen mode.
INPUT
INPUT
| The input signal of the selected region can be selected according to the
user’s needs.
---|---
Optional input signal: SDI, HDMI 1, HDMI 2, HDMI 3, HDMI 4, DP, Auto.
Note: Select Auto, and then the monitor will automatically recognize and match the input signal.
AUDIO
AUDIO
| Volume| 0~100
---|---|---
Audio Source| Digital Region 1, Digital Region 2
Digital Region 3, Digital Region 4
Volume
- Adjust the volume between 0-100.
Audio Source
Digital region 2~4 is only available under multi-disp lays mode and must
activate the corresponding Region under the Select Region function at the same
time.
Note: In 2P LR/ 2P TB/ 2P PIP mode, only Digital Region 1 and Region 2 are available.
SYSTEM
SYSTEM
| Reset| Press to confirm after selecting.
---|---|---
Menu Time| 5~60s
OSD H Position| 0~100 (To set menu display area)
OSD V Position| 0~100 (To set menu display area)
Language| English, Chinese
Transparency| 0~255 (To set menu transparency)
Rotate| 0°, 90°, 270°
Border Width| 0~10
Border Color| R, G, B, W
Back Color| BLACK, BLUE
Low Power Mode| Normal, Sleep, Shutdown
Reset
If there is any problem unknown, press to confirm after selecting. The monitor
will return to the default set.
Menu Time
- Adjust the OSD displaying time from 5 to 60s.
OSD H Position
- Move OSD horizontally from 0 to 100.
OSD V Position
- Move OSD vertically from 0 to 100.
Language
- Switch between English and Chinese.
Transparency
- Set Menu transparency. The more the value, the more transparent it will be. Option value: 0~255.
Rotate
- Flip OSD to three modes: 0° 90° and 270°
Border Width
- Adjust the thickness by using the Border Width function. This setting is available when displayed in 2P LR, 2P TB, 2P PIP, and 4P mode.
Border Color
- Users can choose the border colour among Red, Green, Blue and White.
Low Power Mode
- Adjust the status of the display when there is no signal input, optional: always on, sleep, or shut down.
INFORMATION
- Display the information about all the input of the current Display Mode.
Product Parameters
Display
| Size| 13.3″ OLED
---|---|---
Resolution| 3840×2160
Aspect ratio| 16:9
Brightness| 400 cd/m2
Contrast| 100,000:1
Viewing Angle| 170°/ 170°(H/V)
Color Space| 100% DCI-P3
Input
| ****
HDMI
| HDMI 2.0 x1 (Support up to 4K 60Hz)
HDMI 1.4b ×3 (Support up to 4K 30Hz)
3G-SDI| 1
DP 1.2| 1
Output| 3G-SDI| 1
Supported Formats
| ****
HDMI 2.0
| 2160p 24/25/30/50/60, 1080p 24/25/30/50/60, 1080i
50/60, 720p 50/60…
HDMI 1.4b
| 2160p 24/25/30, 1080p 24/25/30/50/60, 1080i 50/60,
720p 50/60…
3G-SDI
| 1080p 24/25/30/50/60, 1080pSF 24/25/30, 1080i 50/60,
720p 50/60…
DP
| 2160p 24/25/30/50/60, 1080p 24/25/30/50/60, 1080i
50/60, 720p 50/60…
Audio
| Built-in Speakers| 2
Ear Jack| 3.5mm – 2ch 48kHz 24-bit
Power
| DC In| DC 7-24V
Operating power| ≤ 20W (12V)
Environment
| Operating
Temperature
| ****
0°C~50°C
Storage
Temperature
| ****
-20°C~60°C
Other
| Dimension(LWD)| 320 mm x 208 mm x 26.5 mm
Weight| 1.15kg
Accessories
Standard
-
Gimbal Bracket 1 pc
-
0.8M HDMI A/A Cable 1 pair
-
1 5V 3A DC Adapter 1 p c
-
Sunshade 1 pc
-
VESA Mount Plate Bracket 1 pc
-
User Manual Card 1 pc
Optional -
V mount (or Anton Bauer Mount) 1 pc
Trouble Shooting
-
Only black and white display:
Check whether the colour saturation is properly set up or not. -
Power on but no pictures:
Check whether the cables of SDI and HDMI are correctly connected or not. Please use the standard power adapter coming with the product package. Im improper power input may cause damage. -
Wrong or abnormal colours:
Check whether the cables are correctly and properly connected or not. Broken or loose pins in the cables may cause a bad connection. -
When the picture shows a size error:
Press “MENU → FUNCTI
ON → Overscan” to zoom in/out pictures automatically when receiving HDMI signals. -
Other problems:
Please press “MENU” button and choose “MENU→SYSTEM→ Reset →On”.
Note: Due to constant efforts to improve products and product features,
specifications may change without notice.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>