FLASH F7100332 LED PAR 64 18x10W RGBW User Manual

: June 4, 2024
: FLASH

Table of Contents

INTRODUCTION
SAFETY INFORMATION
PRODUCT INFORMATION
INSTALLATION
CONNECTION
DMX CHANNELS
Documents / Resources
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)

FLASH F7100332 LED PAR 64 18x10W RGBW

INTRODUCTION

THANK YOU FOR PURCHASING LED PAR 18x10W RGBW 4in1 IP20. FOR SAFETY REASONS AND TO ENSURE THE TROUBLE-FREE OPERATION, CAREFULLY READ THE INSTRUCTIONS.

SAFETY INFORMATION

Please keep this User Manual for future consultation. If you sell the fixture to another user, be sure that they also receive this instruction booklet.
Unpack and check carefully there is no transportation damage before using the fixture.
Before operating, ensure that the voltage and frequency of power supply match the power requirements of the fixture.
It’s important to ground the yellow/green conductor to earth in order to avoid electric shock.
Disconnect main power before servicing and maintenance.
Use safety chain when fixes this fixture. Don’t handle the fixture by taking its head only, but always by taking its base.
Do not use the device in high humidity conditions. Use in -10°C to +35°C
In the event of serious operating problem, stop using the fixture immediately. Never try to repair the fixture by yourself. Repairs carried out by unskilled people can lead to damage or malfunction. Please contact the nearest authorized technical assistance center. Always use the same type spare parts.
Do not connect the device to any dimmer pack.
Do not touch any wire during operation and there might be a hazard of electric shock.
To prevent or reduce the risk of electrical shock or fire, do not expose the fixture to rain or moisture.
The housing must be replaced if they are visibly damaged.
Do not look directly at the LED light spot while the fixture is on.
WARNING! The device must be connected to the power supply in order to avoid condensation.

PRODUCT INFORMATION

Light source: 18pcs 10W RGBW 4 in 1 LED
Power supply: AC 110V/240V 50/60Hz,
Signal: DMX 512
RGBW color mixing system can create innumerable colors
Housing: Extruded aluminium par housing
Waterproof: IP20
3-Pin XLR DMX input/output
Power consumption: 154 W
Net Weight: 62,2k
Dimensions: H(25)xW(25)xD(25) c
Dim. (box): H(37)xW(25,5)xD(25) cm
Weight (cbox): 2,6 kg

INSTALLATION

The unit should be mounted via its screw holes on the bracket. Always ensure that the unit is firmly fixed to avoid vibration and slipping while operating. Always ensure that the structure to which you are attaching the unit is secure and is able to support a weight of 10 times of the unit’s weight. Also always use a safety cable that can hold 12 times of the weight of the unit when installing the fixture. The equipment must be fixed by professionals. And it must be fixed at a place where is out of the touch of people and has no one pass by or under it.

CONNECTION

The device is equipped with the following interfaces:

DMX (in/out): XLR 3(5)-pin socket
Power (in/out): powerCON socket

Connecting DMX signal

The connection is performed using cable with XLR-female -> XLR-Male plugs.

CAUTION! At the last fixture, the DMX signal has to be terminated with a terminator. Solder a 120Ω resistor between signal (-) and signal (+) into a XLR plug and plug it in the DMX output of the last fixture.

Voltage specification

Input Voltage	Total Power	Frequency
110/240V	154W	50/60Hz

Connecting power supply

The connection is performed using power cable with PowerCon connector ( included ) . Thedevicemustbe operated by qualified personnel.
Make sure that the power grid supply parameters are consistent with device parameters and limitations are not exceeded.

| CAUTION! In the case of cable damage do not attempt to repair. Replacement or repair can be made only on the manufacturer or by a person with appropriate permissions.
Using lamp, the change rate of power voltage should be within ± 10%, if the voltage is too high, it will shorten the light’s life; if it’s not enough, the lamp will be dark. Please restart it after turning off light for 20 minutes until full-cooling. Frequent switching will reduce the life span of lamps and bulbs; intermittent using will improve the life of bulbs and lamps.
---|---

LED Display function

A. Function
B. Up
C. Down
D. Enter

HOW TO OPERATE?
Press button A , there will be eight different effects.
The fist two numeric stands for functions
The last two numeric stands for DMX address, or speed.
You can modify it with B or C button.
D button is to confirm while you settled.

No.	Display	Function
1	D0001	10CHs Address Code, (001—512)

Change the address code by B or C button
2| CC00| 8Colors Changing, (01—99) Color change fast by B or C button
3| CP00| 8colors gradual change, (01—99)
Speed of gradual changing by B or C button
4| CL00| 8 Colors mixed changing, (01—99)
Select color. While change color, with B or C button
5| BEBE| Music activate
6| R220| Red color Changing, (000—255) Change the color by B or C button
7| G220| Green color Changing, (000—255) Change the color by B or C button
8| B220| Blue color Changing, (000—255) Change the color by B or C button
9| W220| Blue color Changing, (000—255) Change the color by B or C button

DMX CHANNELS

Channels	Function	Details
CH.1	Dimmer	R, G, B, dimmer, linear, Dark to Bright
CH.2	Red	R dimmer, linear, Dark to Bright
CH.3	Green	G-dimmer, linear, Dark to Bright
CH.4	Blue	B-dimmer, linear, Dark to Bright
CH.5	White	W-dimmer, linear, Dark to Bright
CH.6	Strobe	1-79 Macro, 80-255 Strobe
CH.7	Sound activated	0-255
CH.8	Color Selection	0-255