ricoo S0922 TV Mount Instruction Manual
- June 12, 2024
- ricoo
Table of Contents
ricoo S0922 TV Mount Instruction Manual
Warning: Do not exceed listed load weight. Property damage oder serious injury may occur!
Dear customer,
we are pleased that you have decided for a product of the brand “RICOO”.
Sometimes, despite our efforts to provide you with a high-quality product, it
may happen that an accessory is missing or a part is damaged during transport.
Please do not return the item in such a case, simply request replacement for
the missing or damaged part at our customer hotline. Contact details from our
customer hotline are listed below.
When contacting us, please mention the article data (listed on top), article
color as well as the required spare part numbers (including the required
quantity of items), as indicated in the “Scope of delivery” section of this
manual.
Please keep ready your order number / order ID for our customer hotline. We
will process your request immediately!
Scope of delivery
**** The numbering on the plastic bag may differ / missing completely!
**** We recommend using a professional level.
Dimension
- A 100 mm 200 mm
- B 100 mm 200 mm
- 100×100 200×100 200×200
Please check BEFORE installation distance between VESA mounting holes on your display!
This screen mount supports VESA hole distance in the minimum and maximum distance ranges given above.
VESA – Hole distance = Distances between the mounting holes on the screen back.
NOTE: Read the entire instruction manual before you start installation and assembly
-
EN ENGLISH NOTE: Read the entire instruction manual before you start installation and assembly
-
Please note: Images in these assembly instructions are only technical presentation of the product. Actual product design may vary minimally.
-
Do not begin the installation until you have read and understood all the instructions and warnings contained in this installation sheet. If you have any questions regarding any of the instructions or warnings, please contact your local distributor.
-
This product was designed to be installed and used ONLY as specified in this manual. Improper installation of this product may cause damage or serious injury.
-
This product may only be assembled / installed by the technical staff.
-
Make sure that the supporting surface will safely support the combined weight of the equipment and all attached hardware and components.
-
When mounting on the wooden beams wall, make sure that the fastening screws are anchored in the center of the beams. It is highly recommended to use a beamfinder.
-
Always use an assistant or mechanical lifting equipment to safely lift and position the equipment.
-
Tighten screws firmly, but do not over tighten. Over tightening can cause damage the items, this greatly reduces their holding power.
-
This product is intended for indoor use only. Using this product outdoors could lead to product failure and personal injury
By reason of large television construction types on the market, we can’t adjust our screen installation materials for each screen type. Therefore it is possible that the screws which are numerously delivered don’t fit with your TV/Monitor. We ask for your understanding that we can’t cover up all possibilities of many screen types.
Each wall is built up of different materials which can result a special requirement. Therefore we are concentrated on the delivery of installation materials only for mass concrete walls. Use our included installation accessories only for mass concrete walls. -
If your walls have a special demand of materials, we advise you to ask in an expert shop for a suitable acquirement of the installation materials.
-
Make sure that before and after the installation of the product neither you nor somebody else can be injured and other objects can be damaged. In case of doubt request for help from an expert.
-
Make also sure that you and optionally the co-helper or representatives have registered the mounting instructions before the installation and also the warning notice.
Assembly Instructions
Warning: Supplied plastic anchors are only suitable for solid concrete
walls!
Use the matching screws and spacers for your display.
If the screws “M-D” are too long, use the plastic spacers “M-G”. (like
in Step 5 B)
**** Use the matching screws and spacers for your display.
(optional)
This Wall Bracket has a rotation function of the front panel. Therefore the
screen is turnable horizontally / vertically. This has the advantage that you
can align horizontally the screen at any time. To permit this function, the
adjusting screws on the front panel are set in the factory so that you can
adjust the screen straightly with your hands without loosen the screws which
is possible without extra tools. With this feature you can align the screen
with your hands in a horizontal or in another desired position when swinging
out or folding of the bracket.
If the factory setting of the rotation function is too strong or free-moving:
Thus you can regulate/control this by loosening or tightening the shown
screws.
Done!
E-Mail: support@ricoo.de www.ricoo.eu
E.N.Z. Engineering GmbH Salzmatten 6 79341 Kenzingen (Germany)
