ricoo D0244 Ceiling Mount TV Instruction Manual
- June 12, 2024
- ricoo
Table of Contents
ricoo D0244 Ceiling Mount TV
Product Information:
- Product Name: Screen Mount
- Model Number: D0244
- Manufacturer: E.N.Z. Engineering GmbH
- Website: www.ricoo.eu
- Email: support@ricoo.de
- Address: Salzmatten 6, 79341 Kenzingen (Germany)
- Support: For any queries or assistance, please contact the manufacturer.
Product Usage Instructions:
- Warning: Do not exceed the listed load weight of 50kg (110lbs) as it may result in property damage or serious injury.
- Before installation, check the distance between the VESA mounting holes on your display.
- This screen mount supports VESA hole distances within the minimum and maximum distance ranges specified in the manual. Mount the screen using the provided components according to the instructions provided.
- Warning: The supplied plastic anchors are only suitable for solid concrete walls. Do not use them on other types of walls.
- If the screws M-C, M-D, M-E are too long for your installation, use the plastic spacers M-G, M-H as shown in Step 6 A.
- Once the installation is complete, ensure that the mount is securely attached and check for any signs of instability before using the screen.
- Note: The use of a professional bubble level is recommended for accurate installation.
Warning: Do not exceed listed load weight. Property damage oder serious injury may occur!
Please check BEFORE installation distance between VESA mounting holes on your
display!
This screen mount supports VESA hole distance in the minimum and maximum
distance ranges given above.
VESA – Hole distance = Distances between the mounting holes on the screen
back.
Scope of delivery
We recommend using a professional level
NOTE: READ THE ENTIRE INSTRUCTION MANUAL BEFORE YOU START INSTALLATION AND ASSEMBLY
- Please note: Images in these assembly instructions are only technical presentation of the product. Actual product design may vary minimally.
- Do not begin the installation until you have read and understood all the instructions and warnings contained in this installation sheet.
- If you have any questions regarding any of the instructions or warnings, please contact your local distributor.
- This product was designed to be installed and used ONLY as specified in this manual.
- Improper installation of this product may cause damage or serious injury.
- This product may only be assembled/installed by the technical staff. Make sure that the supporting surface will safely support the combined weight of the equipment and all attached hardware and components. Always use an assistant or mechanical lifting equipment to safely lift and position the equipment. Make sure that before and after the installation of the product neither you nor somebody else can be injured and other objects can be damaged. In case of doubt request for help from an expert. This product is intended for indoor use only. Using this product outdoors could lead to product failure and personal injury. Tighten screws firmly, but do not over tighten. Over tightening can cause damage the items, this greatly reduces their holding power.
- By reason of large television construction types on the market, we can’t adjust our screen installation materials for each screen type. Therefore it is possible that the screws which are numerously delivered don’t fit with your TV/Monitor. We ask for your understanding that we can’t cover up all possibilities of many screen types.
- Each wall is built up of different materials which can result a special requirement. Therefore we are concentrated on the delivery of installation materials only for mass concrete walls. Use our included installation accessories only for mass concrete walls.
- When mounting on the wooden beams wall, make sure that the fastening screws are anchored in the center of the beams. It is highly recommended to use a beamfinder. If your walls have a special demand of materials, we advise you to ask in an expert shop for a suitable acquirement of the installation materials.
ASSEMBLY INSTRUCTION
Warning: Supplied plastic anchors are only suitable for solid concrete walls!
If the screws “M-C, M-D, M-E” are too long, use the plastic spacers “M-G, M-H”. (like in Step 6 A)
(optional)
This Wall Bracket has a rotation function of the front panel. Therefore the
screen is turnable +/-3° horizontally / vertically. This has the advantage
that you can align horizontally the screen at any time. To permit this
function, the adjusting screws on the front panel are set in the factory so
that you can adjust the screen straightly with your hands without loosen the
screws which is possible without extra tools. With this feature you can align
the screen with your hands in a horizontal or in another desired position when
swinging out or folding of the bracket.
If the factory setting of the rotation function is too strong or free-moving:
Thus you can regulate/control this by loosening or tightening the shown
screws.
E-Mail: support@ricoo.de
www.ricoo.eu
E.N.Z. Engineering GmbH
Salzmatten 6
79341 Kenzingen
(Germany)
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>