ricoo TS2411 Monitor Mount Instruction Manual
- June 12, 2024
- ricoo
Table of Contents
ricoo TS2411 Monitor Mount
Product Information
- Product Name: TS2411
- Manufacturer: E.N.Z. Engineering GmbH
- Address: Salzmatten 6, 79341 Kenzingen (Germany)
- Email: support@ricoo.de
- Website: www.ricoo.eu
Assembly Instructions
Languages: DE, EN, FR, ES, IT
Warning:
Do not exceed the listed load weight. Property damage or serious injury may occur!
VESA Hole Distance:
Please check BEFORE installation the distance between VESA mounting holes on your display. VESA hole distance refers to the distances between the mounting holes on the screen back.
This screen mount supports VESA hole distances in the minimum and maximum distance ranges given above.
Scope of Delivery:
- A x1
- B x1
- C x1
- D x1
- E x1
- F x1
- G x1
- H x1
- M-A x4 (M4x12)
- M-B x4 (M4x16)
- M-C x4 (M5x12)
- M-D x4 (M5x16)
- M-E x4 (M6x12)
- M-F x4 (M6x16)
Usage Instructions:
- Check the VESA hole distance on your display before mounting.
- Ensure that the load weight does not exceed 8kg (17.6lbs).
- Assemble the product using the provided components A, B, C, D, E, F, G, H, M-A, M-B, M-C, M-D, M-E, and M-F.
- Attach component A to the top of the screen.
- Attach component B to the top of the screen.
- Attach component C to the top of the screen.
- Attach component D to the top of the screen.
- Attach component E to the top of the screen.
- Attach component F to the top of the screen.
- Attach component G to the top of the screen.
- Attach component H to the top of the screen.
- Use screws M-A, M-B, M-C, M-D, M-E, and M-F to secure the components to the screen following the specified sizes (in parentheses).
- Ensure all components are securely attached.
- Click component H into place.
- The assembly is now complete.
Note: If you have any questions or need further assistance, please contact our support team via email at support@ricoo.de or visit our website at www.ricoo.eu.
Warning: Do not exceed listed load weight. Property damage oder serious injury may occur!
Please check BEFORE installation distance between VESA mounting holes on your
display!
This screen mount supports VESA hole distance in the minimum and maximum
distance ranges given above.
VESA – Hole distance = Distances between the mounting holes on the screen back
Scope of delivery
NOTE: READ THE ENTIRE INSTRUCTION MANUAL BEFORE YOU START INSTALLATION AND ASSEMBLY
- Please note: Images in these assembly instructions are only technical presentation of the product. Actual product design may vary minimally.
- Do not begin the installation until you have read and understood all the instructions and warnings contained in this installation sheet. If you have any questions regarding any of the instructions or warnings, please contact your local distributor. This product was designed to be installed and used ONLY as specified in this manual. Improper installation of this product may cause damage or serious injury.
- This product may only be assembled/installed by the technical staff. Make sure that the supporting surface will safely support the combined weight of the equipment and all attached hardware and components. Always use an assistant or mechanical lifting equipment to safely lift and position the equipment. Make sure that before and after the installation of the product neither you nor somebody else can be injured and other objects can be damaged. In case of doubt request for help from an expert.
- This product is intended for indoor use only. Using this product outdoors could lead to product failure and personal injury. Tighten screws firmly, but do not over-tighten. Over-tightening can cause damage the items, this greatly reduces their holding power.
- By reason of large television construction types on the market, we can’t adjust our screen installation materials for each screen type. Therefore it is possible that the screws which are numerously delivered don’t fit with your TV/Monitor. We ask for your understanding that we can’t cover up all possibilities of many screen types.
- When mounting on the wooden beams wall, make sure that the fastening screws are anchored in the center of the beams. It is highly recommended to use a beamfinder.
- If your walls have a special demand of materials, we advise you to ask in an expert shop for a suitable acquirement of the installation materials.