ricoo S2722 Monitor Wall Mount Instruction Manual
- June 12, 2024
- ricoo
Table of Contents
ricoo S2722 Monitor Wall Mount
Product Information:
The product is a screen mount designed to securely hold and adjust a display. It supports VESA hole distances in the range of 100x100mm to 200x200mm. The mount has a minimum load weight capacity of 2.5kg (5.5lbs) and a maximum load weight capacity of 20kg (44lbs). It is important not to exceed the listed load weight to prevent property damage or serious injury.
Product Usage Instructions:
-
1. Before installation, check the distance between the VESA mounting holes on your display. - Attach the necessary components to the screen mount:
* Component A x1
* Component B x1
* Component C x1
* Component D x1
* Component E x1
* M-A x4 (M4x14 screws)
* M-B x4 (M5x14 screws)
* M-C x4 (M6x14 screws)
* M-D x4 (M8x20 screws)
* M-E x4 (D5 screws)
* M-F x4 (D8 screws)
* M-G x8 (plastic spacers)
* N-A x4
* N-B x8
* W-A x3
* W-B x3
3. Follow the assembly steps:
1. Attach components A, B, C, D, and E as instructed in Step 2a.
2. Follow the instructions in Step 2b.
3. Proceed to Step 3.
4. Move to Step 4.
5. If the screws M-D are too long, use the plastic spacers M-G as shown in Step 5a.
6. Continue with Step 6.
7. Complete Step 7.
8. Follow the warning and instructions in Step 8.
9. Proceed to Step 9a, then Step 9b, and finally Step 9c.
10. For an optional step, refer to Step 10.
11. Complete Steps 11 and 12.
12. Use the dust catcher as shown in Step 13.
13. The maximum extension of the screen mount is 335mm.
14. Once finished, the installation is complete.
4. Perform the tension-balance adjustment only after the screen assembly:
* Use an Allen key to slightly loosen or tighten the adjustment screw according to the display weight.
* If the display settles on its own, rotate the adjustment screw towards the + symbol.
* If the display rises on its own, rotate the adjustment screw towards the – symbol.Note: Keep the arm level during tension adjustment.
- When removing the display, make sure the front arm is on top to prevent injury caused by the gas pressure spring.
Note: Always refer to the user manual for detailed instructions specific to your product model.
Warning: Do not exceed listed load weight. Property damage oder serious injury may occur!
Please check BEFORE installation distance between VESA mounting holes on your
display!
This screen mount supports VESA hole distance in the minimum and maximum
distance ranges given above.
VESA – Hole distance = Distances between the mounting holes on the screen
back.
Scope of delivery
We recommend using a professional level.
NOTE: READ THE ENTIRE INSTRUCTION MANUAL BEFORE YOU START INSTALLATION AND ASSEMBLY
- Please note: Images in these assembly instructions are only technical presentations of the product. Actual product design may vary minimally.
- Do not begin the installation until you have read and understood all the instructions and warnings contained in this installation sheet. If you have any questions regarding any of the instructions or warnings, please contact your local distributor. This product was designed to be installed and used ONLY as specified in this manual. Improper installation of this product may cause damage or serious injury. This product may only be assembled/installed by the technical staff. Make sure that the supporting surface will safely support the combined weight of the equipment and all attached hardware and components. Always use an assistant or mechanical lifting equipment to safely lift and position the equipment.
- Make sure that before and after the installation of the product neither you nor somebody else can be injured and other objects can be damaged. In case of doubt request for help from an expert. This product is intended for indoor use only. Using this product outdoors could lead to product failure and personal injury. Tighten screws firmly, but do not over-tighten. Over-tightening can cause damage the items, this greatly reduces their holding power.
- By reason of large television construction types on the market, we can’t adjust our screen installation materials for each screen type. Therefore it is possible that the screws which are numerously delivered don’t fit with your TV/Monitor. We ask for your understanding that we can’t cover up all possibilities of many screen types.
- Each wall is built up of different materials which can result a special requirement. Therefore we are concentrated on the delivery of installation materials only for mass concrete walls. Use our included installation accessories only for mass concrete walls.
- When mounting on the wooden beams wall, make sure that the fastening screws are anchored in the center of the beams. It is highly recommended to use a beamfinder. If your walls have a special demand of materials, we advise you to ask in an expert shop for a suitable acquirement of the installation materials.
ASSEMBLY INSTRUCTION
Achtung: Mitgelieferte Dübel sind nur für Massivbetonwände geeignet!
Use the matching screws and spacers for your display
If the screws “M-D” are too long, use the plastic spacers “M-G”. (like in Step 5 A)
WARNING: Perform the tension-balance adjustment only after the screen assembly! This operation must be carried out only with the Allen key!
- Please keep the arm level during tension adjustment. Use a proper Allen key to slightly loosen or tighten the adjustment screw according to the display weight.
- If display settles on its own, rotate adjustment screw towards the “+” symbol.
- If display rises on its own, rotate adjustment screw towards the “-” symbol.
WARNING
DURING THE LATER REMOVING OF THE DISPLAY MAKE SURE THE FRONT ARM IS ON TOP
BEFORE TAKING OFF THE DISPLAY!
Attention: The arm can shoot up upwards because of the gas pressure
spring! If you don’t pay attention you can be injured
This Wall Bracket has a rotation function of the front panel. Therefore the screen is turnable +/-2° horizontally / vertically. This has the advantage that you can align horizontally the screen at any time. To permit this function, the adjusting screws on the front panel are set in the factory so that you can adjust the screen straightly with your hands without loosen the screws which is possible without extra tools. With this feature you can align the screen with your hands in a horizontal or in another desired position when swinging out or folding of the bracket.
E-Mail: support@ricoo.de
www.ricoo.eu
E.N.Z. Engineering GmbH Salzmatten 6 79341 Kenzingen (Germany)
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>