ricoo S2622 Wall Mount TV Swiveling Tilting Instruction Manual
- June 12, 2024
- ricoo
Table of Contents
ricoo S2622 Wall Mount TV Swiveling Tilting
Product Information
- Product Name: Screen Mount
- Model Number: S2622
- Weight Capacity: Minimum: 2.5kg (5.5lbs), Maximum: 20kg (44lbs)
- VESA Compatibility: Supports VESA hole distance in the range of 100x100mm to 200x200mm
- Manufacturer: E.N.Z. Engineering GmbH
- Manufacturer Address: Salzmatten 6, 79341 Kenzingen (Germany)
- Contact Information:
- E-Mail: support@ricoo.de,
- Website: www.ricoo.eu
Product Usage Instructions
- Before installation, check the distance between VESA mounting holes on your display.
- Make sure the load weight does not exceed the maximum weight capacity mentioned above to avoid property damage or serious injury.
- Follow the step-by-step assembly instructions provided in the manual:
- Start by removing the decorative covers.
- Attach the necessary components as per the instructions, using the provided screws and plastic spacers if required.
- Securely fasten the screen mount to the desired location using the appropriate screws.
- Perform the tension-balance adjustment after assembling the screen. Use an Allen key to slightly loosen or tighten the adjustment screw based on the display weight. Keep the arm level during this adjustment.
- When removing the display, ensure that the front arm is on top and exercise caution as the gas pressure spring may cause the arm to shoot upwards.
- Once assembly and adjustment are complete, the installation is done.
Warning: Do not exceed listed load weight. Property damage oder serious injury may occur!
Scope of delivery
Please check BEFORE installation distance between VESA mounting holes on your
display!
This screen mount supports VESA hole distance in the minimum and maximum distance ranges given above.
VESA – Hole distance = Distances between the mounting holes on the screen back.
INSTRUCTION
NOTE: READ THE ENTIRE INSTRUCTION MANUAL BEFORE YOU START INSTALLATION AND ASSEMBLY
Please note: Images in these assembly instructions are only technical presentation of the product. Actual product design may vary minimally. Do not begin the installation until you have read and understood all the instructions and warnings contained in this installation sheet. If you have any questions regarding any of the instructions or warnings, please contact your local distributor. This product was designed to be installed and used ONLY as specified in this manual. Improper installation of this product may cause damage or serious injury. This product may only be assembled / installed by the technical staff. Make sure that the supporting surface will safely support the combined weight of the equipment and all attached hardware and components. Always use an assistant or mechanical lifting equipment to safely lift and position the equipment. Make sure that before and after the installation of the product neither you nor somebody else can be injured and other objects can be damaged. In case of doubt request for help from an expert. This product is intended for indoor use only. Using this product outdoors could lead to product failure and personal injury. Tighten screws firmly, but do not over tighten. Over tightening can cause damage the items, this greatly reduces their holding power.
- By reason of large television construction types on the market, we can’t adjust our screen installation materials for each screen type. Therefore it is possible that the screws which are numerously delivered don’t fit with your TV/Monitor. We ask for your understanding that we can’t cover up all possibilities of many screen types.
- Each wall is built up of different materials which can result a special requirement. Therefore we are concentrated on the delivery of installation materials only for mass concrete walls. Use our included installation accessories only for mass concrete walls.
- When mounting on the wooden beams wall, make sure that the fastening screws are anchored in the center of the beams. It is highly recommended to use a beamfinder. If your walls have a special demand of materials, we advise you to ask in an expert shop for a suitable acquirement of the installation materials.
ASSEMBLY
WARNING:
- Perform the tension-balance adjustment only after the screen assembly! This operation must be carried out only with the Allen key!
- Please keep the arm level during tension adjustment. Use a proper Allen key to slightly loosen or tighten the adjustment screw according to the display weight.
- If display settles on its own, rotate adjustment screw towards the “+” symbol.
- If display rises on its own, rotate adjustment screw towards the “-” symbol.
DURING THE LATER REMOVING OF THE DISPLAY MAKE SURE THE FRONT ARM IS ON TOP
BEFORE TAKING OFF THE DISPLAY!
Attention: The arm can shoot up upwards because of the gas pressure
spring! If you don’t pay attention you can be injured.
This Wall Bracket has a rotation function of the front panel. Therefore the screen is turnable +/-2° horizontally / vertically. This has the advantage that you can align horizontally the screen at any time. To permit this function, the adjusting screws on the front panel are set in the factory so that you can adjust the screen straightly with your hands without loosen the screws which is possible without extra tools. With this feature you can align the screen with your hands in a horizontal or in another desired position when swinging out or folding of the bracket.
E.N.Z. Engineering GmbH
Salzmatten 6
79341 Kenzingen
(Germany)
E-Mail: support@ricoo.de
www.ricoo.eu
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>