RICOO S0544 TV Wall Bracket Flexible and Extendable Instruction Manual
- June 12, 2024
- ricoo
Table of Contents
RICOO S0544 TV Wall Bracket Flexible and Extendable
Product Information
| Language | Text |
|---|---|
| DE | Montageanleitung |
| EN | Assembly Instructions |
| ES | Instrucciones de montaje |
| FR | Notice de montage |
| IT | Instruzioni di montaggio |
Product Usage Instructions
Warning: Do not exceed the listed load weight. Property damage or serious
injury may occur!
VESA Mounting: Please check the distance between VESA mounting holes on
your display before installation. This screen mount supports VESA hole
distance within the given minimum and maximum distance ranges. VESA – Hole
distance: Distances between the mounting holes on the screen back.
Scope of Delivery:
| Component | Quantity |
|---|---|
| A | 1 |
| B | 1 |
| C | 1 |
| D | 2 |
| E | 2 |
| F | 2 |
| G | 4 |
| H | 1 |
| I | 2 |
| J | 1 |
| K | 2 |
| M-A | 4 |
| M-B | 4 |
| M-C | 4 |
| M-D | 4 |
| M-E | 4 |
| M-F | 4 |
| M-G | 8 |
| M-H | 4 |
| W-A | 4 |
| W-B | 4 |
| W-C | 3 |
Mounting Instructions
For mounting on the solid concrete wall:
-
Step 1: Use plastic anchors supplied only for solid concrete walls.|
Step 1: Fix the mount on the wooden beam wall using the components W-A, W-B, and W-C as shown in the diagram. -
Step 2:
Step 2A: If the screws M-C, M-D, and M-E are too long, use the plastic spacers M-G and M-H as shown in the diagram.
Step 2B: If the screws M-C, M-D, and M-E are of appropriate length, skip using the plastic spacers M-G and M-H. -
Step 3:
Step 3A: Attach components D and E to the mount as shown in the diagram.
Step 3B: Attach components B and D to the mount as shown in the diagram.
Step 3C: Attach components C and G to the mount as shown in the diagram. -
Step 4:
Step 4A: Attach components M-D, M-E, M-F, and M-H to the mount as shown in the diagram.
Step 4B: Attach components M-C, M-F, and M-G to the mount as shown in the diagram. -
Step 5:
Step 5A: Attach components M-A, M-B, M-C, M-D, M-E, M-F, M-G, and M-H to the mount as shown in the diagram.
Step 5B: Attach components M-A, M-B, M-C, M-D, M-E, and M-F to the mount as shown in the diagram. -
Step 6:
Step 6A: Attach components W-A, W-B, and W-C to the mount as shown in the diagram. -
Step 7:
Step 7A: Attach components M-C, M-D, M-E, M-F, M-G, and M-H to the mount as shown in the diagram.
Step 7B: Attach components M-C, M-D, M-E, and M-F to the mount as shown in the diagram. -
Step 8:
Step 8A: Attach components K and H to the mount as shown in the diagram. -
Step 9:
Step 9A: Attach components M-C, M-D, M-E, and M-F to the mount as shown in the diagram. -
Step 10:
Step 10A: Attach components M-C, M-D, M-E, and M-F to the mount as shown in the diagram. -
Step 11:
Step 11A: Mounting is complete! If you have any further questions or need assistance, please contact E.N.Z. Engineering GmbH
Email: support@ricoo.de.
Website: www.ricoo.eu.
Address: Salzmatten 6, 79341 Kenzingen (Germany)
OVERVIEW
Please check BEFORE installation
distance between VESA mounting holes on your display! This screen mount
supports VESA hole distance in the minimum and maximum distance ranges given
above. VESA – Hole distance = Distances between the mounting holes on the
screen back.
WHAT INBOX
PARTS
We recommend using a professional level. The numbering on the plastic bag may differ/missing completely!
NOTE: READ THE ENTIRE INSTRUCTION MANUAL BEFORE YOU START INSTALLATION
AND ASSEMBLY
Please note: Images in these assembly instructions are only technical
presentation of the product. Actual product design may vary minimally.
Do not begin the installation until you have read and understood all the
instructions and warnings contained in this installation sheet. If you have
any questions regarding any of the instructions or warnings, please contact
your local distributor. This product was designed to be installed and used
ONLY as specified in this manual. Improper installation of this product may
cause damage or serious injury. This product may only be assembled / installed
by the technical staff. Make sure that the supporting surface will safely
support the combined weight of the equipment and all attached hardware and
components. Always use an assistant or mechanical lifting equipment to safely
lift and position the equipment. Make sure that before and after the
installation of the product neither you nor somebody else can be injured and
other objects can be damaged. In case of doubt request for help from an
expert. This product is intended for indoor use only. Using this product
outdoors could lead to product failure and personal injury. Tighten screws
firmly, but do not overtighten. Over tightening can cause damage the items,
this greatly reduces their holding power. By reason of large television
construction types on the market, we can’t adjust our screen installation
materials for each screen type. Therefore it is possible that the screws which
are numerously delivered don’t fit with your TV/Monitor. We ask for your
understanding that we can’t cover up all possibilities of many screen types.
Each wall is built up of different materials which can result a special
requirement. Therefore we are concentrated on the delivery of installation
materials only for mass concrete walls. Use our included installation
accessories only for mass concrete walls. When mounting on the wooden beams
wall, make sure that the fastening screws are anchored in the center of the
beams. It is highly recommended to use a beamfinder. If your walls have a
special demand of materials, we advise you to ask in an expert shop for a
suitable acquirement of the installation materials.
TOOLS REQUIRED
Warning: Supplied plastic anchors are only suitable for solid concrete walls!
INSTALLATION
For mounting on the solid concrete wall
For mounting on the wooden beam wall
For displays with curved back
Use the matching screws and spacers for your display.
For displays with flat back
Use the matching screws and spacers for your display. If the screws “M-C, M-D,
M-E” are too long, use the plastic spacers “M-G, M-H”. (like in Step 5
A)
This Wall Bracket has a rotation function of the front panel. Therefore the
screen is turnable +/-2° horizontally / vertically. This has the advantage
that you can align horizontally the screen at any time. To permit this
function, the adjusting screws on the front panel are set in the factory so
that you can adjust the screen straightly with your hands without loosen the
screws which is possible without extra tools. With this feature you can align
the screen with your hands in a horizontal or in another desired position when
swinging out or folding of the bracket.
E.N.Z. Engineering GmbH, Salzmatten 6, 79341 Kenzingen (Germany)
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>