ricoo S5064 TV Wall Mount Swivelling and Tilting Instruction Manual
- June 12, 2024
- ricoo
Table of Contents
ricoo S5064 TV Wall Mount Swivelling and Tilting
Product Information
-
Product Name: S5064
-
Manufacturer: E.N.Z. Engineering GmbH
-
Weight Limit: 45kg (99lbs)
-
VESA Compatibility:
- A min.: 200 mm, max.: 630 mm
- B min.: 100 mm, max.: 405 mm
- Supported VESA hole patterns: 200×200, 400×300, 300×200,
400×400, 300×300, 500×300, 400×200, 600×400
-
Package Contents:
- A x1
- B x2
- C x1
- D x1
- M-A x4
- M-B x4
- M-C x4
- M-D x4
- M-E x4
- M-F x4
- M-G x8
- M-H x8
- W-A x6
- W-B x6
- W-C x5
Product Usage Instructions
- Before installation, check the distance between the VESA mounting holes on your display.
- This screen mount supports VESA hole distances within the specified minimum and maximum distance ranges.
- Make sure not to exceed the listed weight limit of 45kg (99lbs) to avoid property damage or serious injury.
- If you are mounting on a solid concrete wall, use the supplied plastic anchors.
- If the screws M-C, M-D, M-H are too long, use the plastic spacers M-G, M-H as shown in Step 5 A.
- Use a professional bubble level for accurate installation.
- Follow the numbered steps in the provided manual to assemble and mount the product.
- Once assembled, you can attach your display to the mount using the appropriate VESA hole pattern.
- Ensure that all screws and components are securely tightened.
- After installation, verify that the mount is properly attached and your display is stable.
- Congratulations! Your installation is complete.
Contact Information:
E.N.Z. Engineering GmbH
Salzmatten 6, 79341 Kenzingen (Germany)
Email: support@ricoo.de
Website: www.ricoo.eu
Assembly Instructions
Warning: Do not exceed listed load weight. Property damage oder serious injury may occur!
Please check BEFORE installation distance between VESA mounting holes on your
display!
This screen mount supports VESA hole distance in the minimum and maximum
distance ranges given above.
Scope of delivery
We recommend using a professional level.
The numbering on the plastic bag may differ/missing completely!
NOTE: READ THE ENTIRE INSTRUCTION MANUAL BEFORE YOU START INSTALLATION
AND ASSEMBLY
Please note: Images in these assembly instructions are only technical
presentation of the product. Actual product design may vary minimally.
Do not begin the installation until you have read and understood all the
instructions and warnings contained in this installation sheet. If you have
any questions regarding any of the instructions or warnings, please contact
your local distributor. This product was designed to be installed and used
ONLY as specified in this manual. Improper installation of this product may
cause damage or serious injury. This product may only be assembled/installed
by the technical staff. Make sure that the supporting surface will safely
support the combined weight of the equipment and all attached hardware and
components. Always use an assistant or mechanical lifting equipment to safely
lift and position the equipment.
Make sure that before and after the installation of the product neither you
nor somebody else can be injured and other objects can be damaged. In case of
doubt request for help from an expert. This product is intended for indoor use
only. Using this product outdoors could lead to product failure and personal
injury. Tighten screws firmly, but do not over-tighten. Over-tightening can
cause damage the items, this greatly reduces their holding power.
By reason of large television construction types on the market, we can’t
adjust our screen installation materials for each screen type. Therefore it is
possible that the screws which are numerously delivered don’t fit with your
TV/Monitor. We ask for your understanding that we can’t cover up all
possibilities of many screen types.
Each wall is built up of different materials which can result a special
requirement. Therefore we are concentrated on the delivery of installation
materials only for mass concrete walls. Use our included installation
accessories only for mass concrete walls.
When mounting on the wooden beams wall, make sure that the fastening screws
are anchored in the center of the beams. It is highly recommended to use a
beamfinder. If your walls have a special demand of materials, we advise you to
ask in an expert shop for a suitable acquirement of the installation
materials.
ASSEMBLY
Warning: Supplied plastic anchors are only suitable for solid concrete walls!
Top
Use the matching screws and spacers for your display.
If the screws “M-C, M-D, M-H” are too long, use the plastic spacers “M-G,
M-H”.
(like in Step 5 A)
E.N.Z. Engineering GmbH, Salzmatten 6, 79341 Kenzingen (Germany)
E-Mail: support@ricoo.de www.ricoo.eu
E.N.Z. Engineering GmbH
Salzmatten 6
79341 Kenzingen
(Germany)