V-TAC VT-8315 LED Prismatic Fitting Light Instruction Manual
- June 12, 2024
- V TAC
Table of Contents
WEEE Number: 80133970
INSTALLATION INSTRUCTION
LED PRISMATIC FITTING
TECHNICAL DATA
MODEL | VT-8315 | VT-8330 | VT-8338 |
---|---|---|---|
WATTS | 15W | 30W | 38W |
INPUT POWER | AC: 220-240V, 50Hz/60Hz | ||
DF | >0.7 | >0.9 | >0.9 |
CRI | >80 | >80 | >80 |
LUMENS | 2250/2300 | 4500/4650 | 5600/5900 |
BEAM ANGLE | 120° | 120° | 120° |
BODY TYPE | PLASTIC | PLASTIC | PLASTIC |
LIFE HOURS | 25,000 HOURS | 25,000 HOURS | 25,000 HOURS |
OPERATING TEMPERATURE | -20°C to +40°C | -20°C to +40°C | -20°C to +40°C |
OPERATING HUMIDITY | 10%”95% | 10%-95% | 10%-95% |
DIMENSIONS | D1(mm) | D2(mm) | L1(mm) |
--- | --- | --- | --- |
15W | 24±1 | 75±1 | 600±2 |
30W | 24±1 | 75±1 | 1200±2 |
38W | 24±1 | 75±1 | 1500±2 |
INTRODUCTION & WARRANTY
Thank you for selecting and buying V-TAC product. V-TAC will serve you the
best. Please read these instructions carefully before starting the
installation and keep this manual handy for future reference.
If you have any another query, please contact our dealer or local vendor from
whom you have purchased the product. They are trained and ready to serve you
at the best. The warranty is valid for 5 years from the date of purchase. The
warranty does not apply to damage caused by incorrect installation or abnormal
wear and tear. The company gives no warranty against damage to any surface due
to incorrect removal and installation of the product. The products are
suitable for 10-12 Hours Daily operation. Usage of product for 24 Hours a day
would void the warranty. This product is warranted for manufacturing defects
only.
WARNING
- Please make sure to turn off the power before starting the installation.
- Installation must be performed by a qualified electrician.
- The light source of this luminaire is not replaceable; when the light source reaches its end of life the whole luminaire shall be replaced.
- For Indoor use only
- Before installation, you must carefully check the integrity of the product and accessories
- When installed, products and flammable materials to ensure that at least 0.2m distance, lighting cannot be installed in the zenith or heat wall, pay attention to low voltage and high voltage electrical wiring separately.
- To ensure that the power cord has enough length, do not kink cables. Output cables should be laid separately and at a distance from other cables.
This marking indicates that this product should not be disposed of with other
household wastes.
Caution, risk of electric shock.
INSTALLATION INSTRUCTIONS
- Choose the right position, drill two hole and insert the screw (make sure the distance between the holes is no less than 50mm, Less than bracket length)
- Shrapnel point it at the hole and then install the screws
- Press the lamp body firmly into the mounting buckle to fix the lamp body, Slide the lamp body along the mounting buckle to the desired position as needed.
- Connect the wiring, use insulating tape, and waterproof tape for insulation and waterproofing, turn the power ON and test.
INSTALLATION DIAGRAM
IN CASE OF ANY QUERY/ISSUE WITH THE PRODUCT, PLEASE REACH OUT TO US AT:
SUPPORT@V-TAC.EU
FOR MORE PRODUCTS RANGE, INQUIRY PLEASE CONTACT OUR DISTRIBUTOR OR NEAREST
DEALERS. V-TAC EUROPE LTD. BULGARIA, PLOVDIV 4000, BUL.L.KARAVELOW 9B
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>