GOLDEN LIGHTING 3712-6SF RBZ Larrick 6 Light Rubbed Bronze Semi-Flush Mount Instruction Manual
- June 12, 2024
- GOLDEN LIGHTING
Table of Contents
GOLDEN LIGHTING 3712-6SF RBZ Larrick 6 Light Rubbed Bronze Semi-Flush
Mount
Product Information
The product is a lighting fixture manufactured by Golden Lighting. It is available in the model number 3712-6SF RBZ. The fixture is designed to provide both task and ambient lighting and can enhance the look of any space. It comes pre-assembled and requires no additional assembly.
Product Usage Instructions
Pendants & Linear Pendants Above a Kitchen Island
To properly install pendants or linear pendants above a kitchen island, follow these steps:
- Center a linear pendant over the island.
- If hanging pendants, use one pendant for every 24 inches of the island.
- Fixtures should hang at least 30 inches above the countertop.
Pendants & Chandeliers Above a Dining Room Table
To properly install pendants or chandeliers above a dining room table, follow these steps:
- Fixtures should stay at least 30 inches above the table.
- Use a fixture that is 12 inches narrower than the width of the table.
Pendants and Chandeliers in Open Areas
To properly install pendants or chandeliers in open areas, follow these steps:
- The bottom of the fixture should hang at least 7.5 feet from the floor.
- Ensure clearance for any opening doors.
To ensure the best lighting in your space, it is recommended to layer your
lighting. Coordinating fixtures like sconces, flush mounts, and pendants can
help you meet your layered lighting needs and reinforce your desired
aesthetic. Install the lights with dimmers that allow you to control the level
of light output at any given moment.
For additional information, expert lighting advice, and to browse coordinating
lights, visit www.GoldenLighting.com.
How to Identify the Fixture’s Wires
The fixture’s wires can be identified as follows:
- Hot: Smooth, Black, or Transparent with Black Inner Thread
- Neutral: Ribbed, White or Transparent with White Inner Thread
- Ground: Copper, Bare Metal, Green, or Transparent Inner Thread
Ensure proper connection of the wires before proceeding with the installation.
Installation Instructions
- Prepare for installation.
- Assemble the fixture (if required).
- Connect the wires.
- Finish the installation by pushing the canopy up to the ceiling and securing it with mounting screws and deco nuts.
- Install light bulbs (not provided) into sockets according to the fixture’s specifications. Do not exceed the maximum recommended wattage.
- Turn on the power and test the fixture.
If you require any assistance or replacement parts, please contact the place of purchase for customer service.
Parts
For Customer Service, contact the place of purchase to arrange for replacement
parts.
IMPORTANT:
- All installation work should be done by accredited professional.
- Shut off power supply at fuse or circuit breaker!
- Use only the specified bulbs. Do not exceed the maximum wattage!
Assembly Instructions
PREPARING FOR INSTALLATION
Carefully remove the new fixture from the carton as well as the yellow bag that holds all of the parts. See the important notes above. Shut off power at the circuit breaker and remove old fixture from wall, including the old mounting strap.
- Mounting strap (B) contains several threaded holes. Two sets of mounting screws (A & D) should be attached to mounting strap (B). You may need to tighten nuts (C) that hold mounting screws (A) in place. If the screws are not attached, please hold canopy (F) up to mounting strap (B). Line up the holes in canopy (F) with the holes in mounting strap (B) and insert mounting screws (A) into mounting strap (B) so that mounting screws (A) protrude through the holes in canopy (F). Mounting screws (A) are long, so please test the canopy against the mounting strap to see how far you should insert the screws.
- Attach mounting strap (B) to the junction box using mounting screws (D) and a screwdriver. Tighten securely. Pull the house wires through the center of mounting strap (B).
- Place the nipple (L) into the post (M) and fasten with nut (K) to secure. Slide column (J) over nipple (L). Place the canopy (F) over nipple (L). Thread washer (I) and nut (H) onto exposed nipple (L) to lock in place. Adjust the six arms (R) to evenly distribute.
ASSEMBLING THE FIXTURE
No Assembly Required – This item arrives assembled and ready for installation.
Please proceed to the next step.
CONNECTING THE WIRES
Have an assistant support the fixture’s weight while completing the wiring. Refer to the wiring diagram and attach the fixture’s wires to the power supply wires from the junction box. Attach the fixture’s wires to the power supply wires from the junction box. Connect Hot to Hot (transparent wire with black inner thread, black, or smooth wire) Neutral to Neutral (transparent wire with white inner thread, white, or ribbed wire), and Ground to Ground (transparent wire with green inner thread, green wire, or copper). Twist the ends of the wire pairs together, and then twist on a wire connector. Make sure all twists are in the same direction. If there is no house ground wire coming from the junction box, locate ground screw (E) on the mounting bracket/mounting strap and wrap the fixture’s ground wire around the ground screw. Use a screwdriver to tighten the top of ground screw (E) onto the wires and into the mounting bracket/mounting strap. Tuck the wires into the junction box.
FINISHING THE INSTALLATION
Push canopy (F) up to the ceiling until mounting screws (A) protrude from the holes in the canopy (F). Thread deco nuts (G) onto the exposed threads of mounting screws (A) until snug against the ceiling to secure. Install light bulbs (not provided) into sockets (N) in accordance with the fixture’s specifications. Do not exceed the maximum recommended wattage. Your installation is complete. Turn on the power and test the fixture.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>