GOLDEN LIGHTING 1210-6 TWP Regent 6 Light Textured White Plaster Chandelier Instruction Manual
- June 12, 2024
- GOLDEN LIGHTING
Table of Contents
GOLDEN LIGHTING 1210-6 TWP Regent 6 Light Textured White Plaster
Chandelier
Product Information
The product is a lighting fixture manufactured by Golden Lighting. It is designed to provide functional and aesthetic lighting solutions for various spaces in your home.
Product Usage Instructions
Pendants & Linear Pendants Above a Kitchen Island
To properly install pendants or linear pendants above a kitchen island:
- Center a linear pendant over the island.
- If using hanging pendants, use one pendant for every 24 inches of the island.
- Fixtures should hang at least 30 inches above the countertop.
Pendants & Chandeliers Above a Dining Room Table
To properly install pendants or chandeliers above a dining room table:
- Fixtures should hang at least 30 inches above the table.
- Use a fixture that is 12 inches narrower than the width of the table.
Pendants and Chandeliers in Open Areas
To properly install pendants or chandeliers in open areas:
- The bottom of the fixture should hang at least 7.5 feet from the floor.
- Ensure clearance for any opening doors.
It is recommended to layer your lighting using coordinating fixtures like sconces, flush mounts, and pendants to achieve bothtask and ambient lighting. Install the lights with dimmers for better control over light output.
For more information and expert lighting advice, visit the Golden Lighting website at www.GoldenLighting.com.
Thank You for Choosing Golden Lighting for Your Lighting Needs!
INSTALLATION
Pendants & Linear Pendants Above a Kitchen Island
Center a linear pendant over the island. If hanging pendants, use one pendant
for every 24″ of island. Fixtures should hang at least 30″ above the
countertop.
Pendants & Chandeliers Above a Dining Room Table
Fixtures should stay at least 30″ above the table. Use a fixture that is 12″
narrower than the width of the table.
Pendants and Chandeliers in Open Areas
The bottom should hang at least 7.5 feet from the floor. Allow clearance for
any opening doors.
We appreciate your business and hope you love your new light!
Great lighting can add value and enhance the look of your home. To ensure the
best lighting in your space, remember to layer your lighting. This ensures
that your space will have both task and ambient lighting. Coordinating
fixtures like sconces, flush mounts, and pendants can help you meet your
layered lighting needs and reinforce your desired aesthetic. Install the
lights with dimmers that allow you to control the level of light output at any
given moment.
Get function and style! Browse our site for coordinating lights and expert lighting advice. To help create the perfect look, visit www.GoldenLighting.com.
Assembly Instructions
How to Identify the Fixture’s Wires
- Hot: Smooth, Black, or Transparent with Black Inner Thread
- Neutral: Ribbed, White or Transparent with White Inner Thread
- Ground: Copper, Bare Metal, Green, or Transparent Inner Thread
For Customer Service, contact the place of purchase to arrange for replacement parts.
IMPORTANT:
- All installation work should be done by accredited professional.
- Shut off power supply at fuse or circuit breaker!
- Use only the specified bulbs. Do not exceed the maximum wattage!
PREPARING FOR INSTALLATION
Carefully remove the new fixture from the carton as well as the yellow bag that holds all of the parts. See the important notes above. Shut off power at the circuit breaker and remove old fixture from wall, including the old mounting strap.
-
From the parts bag remove the mounting strap assembly.
One end of nipple (F) should be attached to mounting strap (A) with washer (C) and hex nut (D) in place. The other end should have canopy loop (H) attached. Attach mounting strap (A) to the junction box using mounting screws (B) and a screwdriver. Tighten securely. Unscrew canopy loop collar (I) from canopy loop (H). Pass canopy (G) over the mounted canopy loop to test the height. Approximately half of the canopy loop’s exterior threads should be exposed, and the canopy loop collar (I) should fit snugly onto the canopy loop (H). Remove canopy (G) and adjust the height of nipple (F) and canopy loop (H) until the desired height is reached.
ASSEMBLING THE FIXTURE -
Measure to determine the correct amount of chain and wire needed for proper hanging height. If necessary, use a pair of pliers to open and remove any excess chain. Attach one of the chain connectors (K) to each end of the chain (J). Pass the fixture’s wires through the top loop (L). Attach one end of the chain (J) to the top loop (L) using chain connector (K) and close chain connector (K). Attach one end of each rod (N) to decorative hooks (O) on the fixture’s body (P). Use the free end of the rod (N) to attach the rod to the hooks on the top cap (M). Use the free chain connector (K) to attach chain (J) to the canopy loop (H). Feed the fixture wires up through the chain (every three links or so), pulling the wires until taut. Trim the wires to the desired length plus 8 to 10 inches.
CONNECTING THE WIRES -
Have an assistant support the fixture’s weight while completing the wiring.
Refer to the wiring diagram and attach the fixture’s wires to the power supply wires from the junction box. Attach the fixture’s wires to the power supply wires from the junction box. Connect Hot to Hot (transparent wire with black inner thread, black, or smooth wire) Neutral to Neutral (transparent wire with white inner thread, white, or ribbed wire), and Ground to Ground (transparent wire with green inner thread, green wire, or copper). Twist the ends of the wire pairs together, and then twist on a wire connector. Make sure all twists are in the same direction. If there is no house ground wire coming from the junction box, locate ground screw (E) on the mounting bracket/mounting strap and wrap the fixture’s ground wire around the ground screw. Use a screwdriver to tighten the top of ground screw (E) onto the wires and into the mounting bracket/mounting strap. Tuck the wires into the junction box.
FINISHING THE INSTALLATION -
Push canopy (G) up to the ceiling and slide canopy loop collar (I) up beneath the canopy. Tightly thread canopy loop collar (I) onto canopy loop (H) to secure canopy (G) in place. Tighten decorative finials (Q) onto threads at the bottom of fixture frame (P) and adjust to horizontal and vertical. 5.
Carefully slide glass shades (U) over sockets (R). Candle sleeves (S) have retaining rings attached. Each retaining ring has two small holes in each side.
The glass shade opening is tight. Carefully push the candle sleeves down into the glass shades and over the sockets. 6. Carefully place the tips of socket tool (T) into the holes in the retaining ring. Use socket tool (T) to thread the retaining rings onto the socket threads. This will secure the glass in place.
Install light bulbs (not provided) into sockets (R) in accordance with the fixture’s specifications. Do not exceed the maximum recommended wattage.
Your installation is complete. Turn on the power and test the fixture.
Love your light and want to show it off?
Follow us, share a picture, and tag us on Social…
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>