GOLDEN LIGHTING 1821-WT1 BI-RO Madera Large 1-Light Black Iron Wall Sconce Instruction Manual
- June 12, 2024
- GOLDEN LIGHTING
Table of Contents
GOLDEN LIGHTING 1821-WT1 BI-RO Madera Large 1-Light Black Iron Wall Sconce Instruction Manual
Pendants & Linear Pendants Above a Kitchen Island
Center a linear pendant over the island. If hanging pendants, use one pendant
for every 24″ of island. Fixtures should hang at least 30″ above the
countertop.
Pendants & Chandeliers Above a Dining Room Table
Fixtures should stay at least 30″ above the table. Use a fixture that is 12″
narrower than the width of the table.
Pendants and Chandeliers in Open Areas
The bottom should hang at least 7.5 feet from the floor.
Allow clearance for any opening doors.
We appreciate your business and hope you love your new light!
Great lighting can add value and enhance the look of your home. To ensure the best lighting in your space, remember to layer your lighting. This ensures that your space will have both task and ambient lighting. Coordinating fixtures like sconces, flush mounts, and pendants can help you meet your layered lighting needs and reinforce your desired aesthetic. Install the lights with dimmers that allow you to control the level of light output at any given moment.
Get function and style! Browse our site for coordinating lights and expert lighting advice. To help create the perfect look, visit www.GoldenLighting.com.
Love your light and want to show it off?
Follow us, share a picture, and tag us on Social…
Assembly Instructions: 1821-WT1
Get help, quick tips, and explore curated content
For Customer Service, contact the place of purchase to arrange for replacement parts.
IMPORTANT:
- All installation work should be done by accredited professional.
- Shut off power supply at fuse or circuit breaker!
- Use only the specified bulbs. Do not exceed the maximum wattage!
Assembly Instructions:
PREPARING FOR INSTALLATION
Carefully remove the new fixture from the carton as well as the yellow bag that holds all of the parts. See the important notes above. Shut off power at the circuit breaker and remove old fixture from wall, including the old mounting strap. (PLEASE NOTE: This fixture has multiple installation options. Before beginning, please review these instructions carefully.) TO INSTALL ON A WALL AND POWER THE FIXTURE USING THE PLUG REFER TO DIAGRAM (1): 1. Mounting plate (N) is attached to backplate (D). Remove mounting plate (N) from backplate (D). Hold the fixture up to the wall to test placement for backplate (D). After you determine the proper placement, hold mounting plate (N) up to the wall and use a pencil to mark the wall through the circular holes in mounting plate (N). 2. Use a drill bit to create two holes on your pencil marks and insert plastic screw anchors (A) into the holes made until the plastic screw anchors are flush with the wall. Align mounting plate (N) with the plastic screw anchors (A). Using screwdriver insert mounting screws (S) into the plastic screw anchors (A) halfway, and fix the mounting plate (N). Do not insert the entire screw flush to the wall. Leave a few of the screw’s threads outside of the wall for now. 3. The fixture’s ground wire is wrapped inside of backplate (D). Leave the ground wire unattached and wrapped inside the backplate. TO INSTALL OVER AN EXISTING JUNCTION BOX AND HARDWIRE THE FIXTURE REFER TO DIAGRAM (2) AND THE SIDE DIAGRAMS WHICH DIFFERENTIATE MOUNTING PLATE (N) FROM MOUNTING PLATE (B): 1. To begin, remove mounting plate (N) from backplate (D). Then remove screws (C) and nuts from mounting plate (N) and install them on mounting plate (B). Hold mounting plate (B) up to the junction box and check that the install holes are parallel. Use a pencil to mark the wall through the circular holes in mounting plate (B). 2. Use a drill bit to create two holes on your pencil marks and insert plastic screw anchors into the holes made until the plastic screw anchors are flush with the wall. Align mounting plate (B) with the plastic screw anchors. Using screwdriver, insert mounting screws (S) into the plastic screw anchors halfway, and fix the mounting plate (B). 3. Pull the house wires from the junction box through the center of mounting plate (B). Secure mounting bracket (B) to the junction box with mounting screws (A) and a screwdriver. Tighten the screws securely. Leaving at least 8 to 10 inches of cord for wiring, use a pair of wire cutters to trim the plug from cord (M). Pull the cord up through the hole in the bottom of backplate (D) and plug the hole with stopper (N).
ASSEMBLING THE FIXTURE
No Assembly Required – This item arrives assembled and ready for installation.
Please proceed to the next step.
CONNECTING THE WIRES
IF HARDWIRING THE FIXTURE TO WALL, REFER TO DIAGRAM (2) AND THE WIRING
INSTRUCTIONS BELOW. DO NOT FOLLOW THESE WIRING INSTRUCTIONS IF YOU ARE
MOUNTING FIXTURE TO THE WALL AND
USING PLUG TO POWER FIXTURE, ALSO REFERRED TO AS DIAGRAM (1). 4. Have an assistant support the fixture’s weight while completing the wiring. Refer to the wiring diagram and attach the fixture’s wires to the power supply wires from the junction box. Attach the fixture’s wires to the power supply wires from the junction box. Connect Hot to Hot (transparent wire with black inner thread, black, or smooth wire) Neutral to Neutral (transparent wire with white inner thread, white, or ribbed wire), and Ground to Ground (transparent wire with green inner thread, green wire, or copper). Twist the ends of the wire pairs together, and then twist on a wire connector. Make sure all twists are in the same direction. If there is no house ground wire coming from the junction box, locate ground screw (E) on the mounting bracket/mounting strap and wrap the fixture’s ground wire around the ground screw. Use a screwdriver to tighten the top of ground screw (E) onto the wires and into the mounting bracket/mounting strap. Tuck the wires into the junction box.
FINISHING THE INSTALLATION
(PLEASE NOTE: This fixture has multiple installation options. Before
beginning, please review these instructions carefully.) TO INSTALL ON A WALL
AND POWER THE FIXTURE USING THE PLUG REFER TO DIAGRAM (1): 5. Place backplate
(D) over mounting strap (N) so that mounting screws (C) protrude through the
holes in backplate (D). Secure the backplate (D) to the mounting strap (N)
with decorative nuts (F). Twist until the backplate (D) of the fixture is snug
against the wall. 6. Unscrew finial (K) from the threads on top of harp fitter
(H). Set finial (K) aside for later. Place the harp fitter (H) into saddle (G)
until caps on harp fitter (H) slide down onto saddle (G). 7. Install a light
bulb (not included) into socket in accordance with the fixture’s
specifications. Do not exceed the maximum recommended wattage. 8. Put the
cloth shade (J) on the top thread of the harp fitter (H) and secure with
finial (K). 9. Plug cord into the nearest outlet. Your installation is now
complete. Twist knob (L) clockwise to turn on the fixture. To power the
fixture off, twist the knob (L) clockwise. TO INSTALL OVER AN EXISTING
JUNCTION BOX AND HARDWIRE THE FIXTURE REFER TO DIAGRAM (2): 5. Place backplate
(D) over mounting strap (B) so that mounting screws (C) protrude through the
holes in backplate (D). Secure the backplate (D) to the mounting strap (B)
with decorative nuts (F). Twist until the backplate (D) of the fixture is snug
against the wall. 6. Unscrew finial (K) from the threads on top of harp fitter
(H). Set final (K) aside for later. Place the harp fitter (H) into saddle (G)
until caps on harp fitter (H) slide down onto saddle (G). 7. Install a light
bulb (not included)
into socket in accordance with the fixture’s specifications. Do not exceed the
maximum recommended wattage. 8. Put the cloth cover (J) on the top thread of
the harp fitter (H) and secure with finial (K). 9. Your installation is now
complete. Twist knob (L) clockwise to turn on the fixture. To power the
fixture off, twist the knob (L) clockwise.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>