GOLDEN LIGHTING 1088-M BLK-CLR Adeline 1 Light Matte Black Pendant Light Instruction Manual

GOLDEN LIGHTING 1088-M BLK-CLR Adeline 1 Light Matte Black Pendant Light

Product Information

The product is a lighting fixture manufactured by Golden Lighting. It is available in model number 1088-M and comes in a black and clear color combination. The fixture is designed to provide both task and ambient lighting, enhancing the look of your home. It can be used in various areas such as kitchen islands, dining room tables, and open spaces. The fixture is compatible with dimmers, allowing you to control the level of light output.

Product Usage Instructions

Pendants & Linear Pendants Above a Kitchen Island:

To properly install the fixture above a kitchen island, follow these steps:

• Center a linear pendant over the island.
• If hanging pendants, use one pendant for every 24 inches of the island.
• Fixtures should hang at least 30 inches above the countertop.

Pendants & Chandeliers Above a Dining Room Table:

To properly install the fixture above a dining room table, follow these steps:

• Fixtures should stay at least 30 inches above the table.
• Use a fixture that is 12 inches narrower than the width of the table.

Pendants and Chandeliers in Open Areas:

To properly install the fixture in open areas, follow these steps:

• The bottom of the fixture should hang at least 7.5 feet from the floor.
• Allow clearance for any opening doors.

Refer to the assembly instructions provided for detailed steps on how to assemble and install the fixture. Make sure to connect the fixture’s wires correctly and finish the installation properly. Install light bulbs (not included) into the socket according to the fixture’s specifications, ensuring not to exceed the maximum recommended wattage. Once the installation is complete, turn on the power and test the fixture. For any further assistance or replacement parts, please contact the place of purchase. To browse for coordinating lights and expert lighting advice, visit www.GoldenLighting.com. Thank You for Choosing Golden Lighting for Your Lighting Needs!

DIMENSION

• Pendants & Linear Pendants Above a Kitchen Island
  Center a linear pendant over the island. If hanging pendants, use one pendant for every 24″ of the island. Fixtures should hang at least 30″ above the countertop.

• Pendants & Chandeliers Above a Dining Room Table
  Fixtures should stay at least 30″ above the table. Use a fixture that is 12″ narrower than the width of the table.

• Pendants and Chandeliers in Open Areas
  The bottom should hang at least 7.5 feet from the floor. Allow clearance for any opening doors.

We appreciate your business and hope you love your new light!
Great lighting can add value and enhance the look of your home. To ensure the best lighting in your space, remember to layer your lighting. This ensures that your space will have both task and ambient lighting. Coordinating fixtures like sconces, flush mounts, and pendants can help you meet your layered lighting needs and reinforce your desired aesthetic. Install the lights with dimmers that allow you to control the level of light output at any given moment. Get function and style! Browse our site for coordinating lights and expert lighting advice. To help create the perfect look, visit www.GoldenLighting.com.
Love your light and want to show it off?
Follow us, share a picture, and tag us on Social…

Assembly Instructions

How to Identify the Fixture’s Wires

• Hot: Smooth, Black, or Transparent with Black Inner Thread
• Neutral: Ribbed, White or Transparent with White Inner Thread

Get help, quick tips, and explore curated content For Customer Service, contact the place of purchase to arrange for replacement parts.

IMPORTANT:

• All installation work should be done by accredited professional.
• Shut off power supply at fuse or circuit breaker!
• Use only the specified bulbs. Do not exceed the maximum wattage!

PREPARING FOR INSTALLATION
Carefully remove the new fixture from the carton as well as the yellow bag that holds all of the parts. See the important notes above. Shut off power at the circuit breaker and remove old fixture from wall, including the old mounting strap. 1. From the parts bag remove the mounting strap (A) assembly. One end of nipple (F) should be attached to mounting strap (A) with washer (C) and hex nut (D) in place. The other end should have canopy loop (H) attached. Attach mounting strap (A) to the junction box using mounting screws (B) and a screwdriver. Tighten securely. 2. Unscrew canopy loop collar (I) from canopy loop (H). Pass canopy (G) over the mounted canopy loop (H) to test the height. Approximately half of the canopy loop’s (H) exterior threads should be exposed, and the canopy loop collar (I) should fit snugly onto the canopy loop (H). Remove canopy (G) and adjust the height of nipple (F) and canopy loop (H) until the desired height is reached.

ASSEMBLING THE FIXTURE
(PLEASE NOTE: The adjustable ring (Q) will differ in shape by fixture finish. Please refer to the diagram to determine which adjustable ring shape fixture will use.) 3. By measuring, determine the correct of the number of rods (L & M) needed for proper hanging height. Carefully put the wires through the desired rods (L & M) and connect all rods together. Thread one end of the rods to small loop (K) and the other end to another small loop (P). Secure the small screw (N) to the small loop (P) by the short rod (L). Carefully pull out the wires from the rods until taut. Feed the remaining fixture wire through chain link (J), up canopy loop collar (I), canopy loop (H), canopy (G), and nipple (F). Connect the small loop (K) on the rod and the canopy loop (H) with the chain link connector (J). Close the connector to secure. 4. Connect the small ring (P) and the bottom loop (R) by the adjustable ring (Q).
CONNECTING THE WIRES
5. Have an assistant support the fixture’s weight while completing the wiring. Refer to the wiring diagram and attach the fixture’s wires to the power supply wires from the junction box. Attach the fixture’s wires to the power supply wires from the junction box. Connect Hot to Hot (transparent wire with black inner thread, black, or smooth wire) Neutral to Neutral (transparent wire with white inner thread, white, or ribbed wire), and Ground to Ground (transparent wire with green inner thread, green wire, or copper). Twist the ends of the wire pairs together, and then twist on a wire connector. Make sure all twists are in the same direction. If there is no house ground wire coming from the junction box, locate ground screw (E) on the mounting bracket/mounting strap and wrap the fixture’s ground wire around the ground screw. Use a screwdriver to tighten the top of ground screw (E) onto the wires and into the mounting bracket/mounting strap. Tuck the wires into the junction box.

FINISHING THE INSTALLATION

6. Attached the glass (V) to the glass holder (S) and secure with the decorative ring (W). 7. Raise canopy (G) up to the ceiling and slide canopy loop collar (I) up beneath the canopy (G). Tightly thread canopy loop collar (I) onto canopy loop (H) to secure canopy (G) in place. 8. Install light bulbs (not included) into the socket (U) in accordance with the fixture’s specifications. Do not exceed the maximum recommended wattage. Your installation is now complete. Turn on the power and test. GoldenLighting.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>