ONE FOR ALL URC 6820 Zapper+ Universal Remote Control Installation Guide

ONE FOR ALL URC 6820 Zapper+ Universal Remote Control

Product Information

The URC 6820 is a universal remote control manufactured by UNIVERSAL ELECTRONICS. It is designed to control various devices such as TVs, set-top boxes, sound bars, AV receivers, and more. The remote control comes with a 3-year warranty, guaranteeing it to be free from defects in materials and workmanship.

Product Disposal

The URC 6820 is manufactured using high-quality components that can be recycled and reused. Therefore, it should not be disposed of with normal household waste. Please refer to local regulations for proper collection or disposal of electrical and electronic products to prevent negative effects on the environment and/or human health.

Battery Disposal

When disposing of the batteries used in the URC 6820, do not throw them away with normal household waste. Refer to local regulations for proper collection or disposal to prevent potential negative effects on the environment and/or human health.

Warranty

The URC 6820 is covered by a 3-year warranty from the date of original purchase. If the product is proven to be defective within this period, it will be repaired or replaced free of charge. The owner is responsible for forwarding costs, while the costs of returning the product are covered by UNIVERSAL ELECTRONICS. To obtain warranty service, contact […], and provide the original purchase receipt as proof of eligibility.

Product Usage Instructions

Battery Installation

To install batteries in the URC 6820:

1. Open the battery door.
2. Insert 2 AAA batteries, ensuring correct polarity.

Remote Setup

To set up your URC 6820 remote control:

1. For learning mode, hold down AV and Exit buttons until the red LED blinks twice.
2. Press and release the key you want to learn a function onto (e.g., Power).
3. Press and release the corresponding key on the original remote to learn the function.
4. The red LED will blink twice to indicate successful learning.
5. You can learn functions from multiple remotes, but only one function per key.
6. Once all required functions are learned, press and hold the OK key until the red LED blinks twice to exit learning mode.

For further information and support, visit www.ofa.com/urc6820.

WELCOME, PREPARE YOUR REMOTE FOR INSTALLATION

CAUTION: Risk of explosion if the battery is replaced by an incorrect type. Use quality Alkaline batteries.

PRODUCT DISPOSAL

The crossed-out wheeled bin symbol on this product ensures that this product is manufactured using high-quality components that can be recycled and reused according to European Directive 2012/19/EU. Please do not dispose of this product with your normal household waste, refer to local regulations for the proper collection or disposal of electrical and electronic products. This will help in preventing negative effects on the environment and/or human health.
BATTERY DISPOSAL (EUROPEAN DIRECTIVE
2006/66/EC) Please do not dispose of your batteries with your normal household waste, refer to local regulations for the proper collection or disposal. This will help prevent potential negative effects on the environment and/or human health.
GUARANTEE TERMS AND CONDITIONS
UNIVERSAL ELECTRONICS warrants to the original purchaser that this product will be free from defects in materials and workmanship under normal and correct use for a period of 3 years from the date of the original purchase. This product will be repaired or if necessary, replaced free of charge if it has been proven to be defective within the 3-year warranty period. The forwarding costs are on the account of the owner; the costs of returning the product are on the account of UNIVERSAL ELECTRONICS. This warranty does not cover damage or failures caused by products or services not supplied by UNIVERSAL ELECTRONICS, or which result from not mounting the product according to manual instructions. This also applies when the product has been modified/repaired by others than UNIVERSAL ELECTRONICS or if a fault is the result of an accident, misuse, abuse, neglect, mishandling, misapplication, faulty installation, improper maintenance, alteration, modifications, fire, water, lightning, natural disasters, wrong use or carelessness. To obtain warranty service during the warranty period contact […], and please note that we need your original purchase receipt so that we may establish your eligibility for service. If you have bought this product for purposes that are not related to your trade, business, or profession, you may have legal rights under your national legislation governing the sale of consumer goods. This guarantee does not affect those rights. www.oneforall.com.
Thank you for purchasing the One For All Zapper+.
The remote features the most commonly used keys for control of your home entertainment devices, which can be customized using the handy learning feature to perform exactly the way you need them to. You could for example just learn the volume, power, and channels of your TV in the kitchen, or combine the control of your TV, Set Top Box, and even Sound Bar in the living room. There are also 2 Power keys for combining more than one device together on a single remote.

KEY TABLE

HOW TO SET UP YOUR REMOTE

A – LEARNING
Your One For All remote control can learn any function from any other working remote control. This is a quick and easy one-time setup that will allow you to control one or more of your home entertainment devices, and even combine multiple devices in one easy-to-use remote control – for example, you could teach the volume keys to control your Sound Bar, the TV Power and AV keys to control your TV, and the rest of the keys to control your Set Top Box (Satellite, Cable or Freeview Receiver). To do this, firstly make sure you have all your original remote controls to hand, and that they have working batteries. To learn functions, the original remote should be approximately 3cm from the OFA remote, pointing towards it as shown below:

1. Hold down AV and Exit until the red LED blinks twice.
2. Press and release the key you want to learn a function onto (for example the TV Power key) – The red LED will blink continuously.
3. Press and release* the corresponding key on the original remote, for example, Power.
4. The red LED will blink twice to indicate the key has been learned correctly.
5. Repeat steps 2 and 3 for each key you want to learn – remember you can learn from multiple remotes, but only one function per key.
6. When you learned all the functions you require, press and hold the OK key until the red LED blinks twice.

Hints

• If the red LED shows one long blink at step 4, the function was not learned correctly, please try again from step 2.
• If you find one or more keys don’t work properly after set up, you can re-enter the learning mode at any time by repeating the procedure from step 1.
• To delete a learned function, hold down Guide and Menu until the red LED blinks twice, and press the key to delete twice.
• If one or more of your original remotes aren’t working, you can still set up the One For All remote by SimpleSet (B) or Code Set Up (C).
• Some remotes send commands differently. If you find a function that cannot be learned, try holding down the key on the original remote instead of pressing and releasing it.

B – SIMPLESET
If the brand of your device is listed below, you can also set up your device using the One For All SimpleSet system:
TV

1. Bush
2. Grundig
3. LG
4. Panasonic
5. Philips
6. Samsung
7. Sharp
8. Sony
9. Thomson, TCL
10. 0 Toshiba

Set Top Box (Satellite, Cable, Freeview/DVB-T)

1. BSkyB / Sky Ireland / Orange
2. Canal+ / CanalSat / Digital+
3. Dream Multimedia / TechniSat
4. DStv / Multichoice / Foxtel / Sky New Zealand
5. freebox / Tricolor TV / Vu+
6. Humax
7. Samsung
8. Sky Italia / SFR / Neuf TV
9. Sky Deutschland / Sky Österreich / T-Home / Deutsche Telekom
10. 0 UPC / Cablecom / UPC Direct / Virgin Media

Audio Sound Bars, AV Receivers etc

1. Bose
2. Denon
3. LG
4. Marantz / Philips
5. Onkyo
6. Panasonic / Technics
7. Pioneer
8. Samsung
9. Sony
10. 0 Yamaha

B – SIMPLE SET
To set up your device:

1. Turn on your device (not on standby) and point the OFA remote towards it.

2. To set up:
   TV
   hold down TV Power and STB Power until the red LED blinks twice. STB
   (CABLE, SATELLITE, FREEVIEW, DVB-T) – hold down Volume + and Channel + until the red LED blinks twice. AUDIO
   (RECEIVER, SOUND BAR) – hold down Volume – and Channel – until the red LED blinks twice.

3. Hold down the digit for your brand and device as listed left (e.g. 6 for Samsung TV).

4. The remote will send Power every 3 seconds until your device switches off.

5. As soon as your device switches off, release the digit.

6. The red LED will blink twice and the remote should now operate your device.

   • If you find one or more keys do not work as you expect, start again at step 2 – the remote will start with the next code in the memory.
   • If you set up a Set Top Box and then an Audio device, to turn the Audio device back on hold the STB Power key for 3 seconds – the key will send STB Power and then Audio Power.

C – SET UP BY CODE
If your brand is not listed in section B, you can set up your device by trying codes individually. To do this:

1. Turn on your device (not on standby).

2. Locate the brand of your device in the code list (pages 77 – 93). Codes are listed by Device Type and Brand.

3. To set up:
   TV
   hold down TV Power and STB Power until the red LED blinks twice. STB
   (CABLE, SATELLITE, FREEVIEW, DVB-T) – hold down Volume + and Channel + until the red LED blinks twice. AUDIO
   (RECEIVER, SOUNDBAR) – hold down Volume – and Channel – until the red LED blinks twice.

4. Enter the first 4 digit code listed for your brand (e.g. 0556 for Bennett).

5. The red LED will blink twice.

6. Now aim the remote towards your device and press the Power (or Mute*) key.

7. If the device turns off (or mutes*), your remote is ready to use. If not, repeat steps 3-6 with the next code in the list.

   • If you have already set up a Set Top Box and you are setting up Audio as well, please try the Mute key during step 6.

AFTER THE SIMPLEST OR CODE SETUP

Your One For All Zapper+ can operate up to three devices. If you only set up one device, all keys will operate that device. If you set a TV and Set Top Box, most keys will operate the Set Top Box, with the exception of the TV Power Key, the Volume Up, Down and Mute, and the AV key. If you set up a TV, Set Top Box, and an Audio device such as a sound bar, the Volume Up, Down and Mute keys will control your Audio device. Also if you hold down the Set Top Box Power key for three seconds it will first send Power for the Set Top Box, and then for the Audio Device. As the AV key is intended to select the input on your TV and most TVs use a menu to select from a list of inputs, when the AV key is pressed and a TV and STB are set up, the Menu Up, Down, Left, Right and OK keys temporarily control the TV. If the OK key is pressed, or no key is pressed for ten seconds, these keys will revert to controlling your Set Top Box.

Connect with us

• at facebook.com/oneforallworldwide.
• @oneforall.worldwide
• linkedin.com/company/one-for-all-worldwide/.
• youtube.com/user/oneforallproducts.
• Universal Electronics BV –
• Europe & International
• P.O. Box 3332, 7500 DH Enschede
• The Netherlands
• RDN-1150323 – 710335

References

• One For All - One For All
• One For All - One For All
• Home | One For All

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>