BenQ V5000i TV Projector Installation Guide
- June 12, 2024
- BenQ
Table of Contents
BenQ V5000i TV Projector
Product Information
The product is a digital projector called TV Projector V5000i. It comes with an installation guide and a warranty card. The product also includes a remote control, ATV dongle (QS02), and an ALR screen. The projector has a model number of 4J.JRA01.001 V1.01.
Product Usage Instructions
- Before getting started, ensure that you have a Google account and the projector’s location has wireless Internet. Also, check the size of your projection wall/screen and determine where to install the projector.
- Remove the lens stickers before use to avoid damage to the lens.
- Install batteries into the remote control provided with the projector. Do not use the QS02 remote control.
- Connect the ATV dongle and power cord.
- Place the projector according to the recommended measurements provided in the manual.
- Connect the audio systems if desired.
- Power on the projector and complete the initial setup.
- Adjust the screen size and alignment using the integrated measuring tools.
- Make the necessary connections, including HDMI, audio return, SPDIF audio out, service, RS-232, 12V trigger, and media reader.
- Refer to the specifications for detailed information about the product’s optical resolution.
Note: Fine adjustments may be required for installation according to individual needs.
IMPORTANT
To install the projector properly, you are strongly recommended to follow the
steps and safety precautions in this document.
What’s In The Box
What You Need To Know Before You Buy Your Laser TV Scan to watch how-to videos.
Before getting started
Ensure you have a Google account and the projector’s location has wireless Internet, then check the size of your projection wall/screen and determine where to install the projector.
Note: For details for projector placement, see “Measurements” on page 8.
-
Remove lens stickers.
Failure to remove stickers before use may cause damage to the lens. -
Install batteries to the remote control.
Only use the remote control provided with the projector.
Do not use the QS02 remote control (availability may vary by country/region). -
Connect ATV dongle and power cord.
-
Place the projector.
90″ Measurements of 90″ projection screen -
100″ Measurements of 100″ projection screen Note: Values are provided for your quick installation. Fine adjustments may be required according to your needs.
Using the integrated measuring tools
to measure distance from projector to the wall
Distance to the wall
Recommended for 100” ALR screen with frame depth of 2.7 cm.
Power on and complete initial setup.
Projector Position
Screen adjustment
Image size
Image alignment
Keystone correction
Retract the measuring tools.
Connections
Specifications
Note All specifications are subject to change without notice.
-
Optical
Resolution: 4K UHD 3840 x 2160
Display system: 1-CHIP DMD
Lens: F = 2.0, f = 2.403 mm
Clear focus range: 70” – 100”
Light source: Laser -
Electrical
Power supply: AC100–240V, 50–60 Hz (Automatic)
Power consumption: 250 W (Max); < 0.5 W (Standby) -
Mechanical
Size: 358 (W) x 760 (L) x 164 (H) mm (with foot)
Weight: 13.2 Kg + 200 g (29.12 + 0.44 lbs) -
Output terminals
Speaker
15 watt x 2, 5 watt x 2
Audio signal output
Audio line-out (3.5″) x 1 S/PDIF x 1 -
Control
USB: Type-A x 3 (1.5A/2.5A power supply)
RS-232 serial control: 9 pin x 1
DC 12V trigger x 1
IR receiver x 2
Input terminals: Video signal input
Digital: HDMI (HDCP 2.2) x 3 -
Environmental Requirements
Operating temperature 0°C–40°C at sea level
Storage temperature -20°C–60°C at sea level
Operating/Storage relative humidity 10%–90% (without condensation)
Operating altitude 0–1499 m at 0°C–35°C
1500–3000 m at 0°C–30°C (with High Altitude Mode 1 on)
Storage altitude 30°C @ 0–12,200 m above sea level -
Transporting
Original packing or equivalent is recommended. -
Repairing
Please visit your local website from http://Support.BenQ.com and find your service contact window.
Notice
To ensure safe use of this product, please read the user manual for details
before you operate your projector.
Risk Group 2
- According to the classification of photobiological safety of light sources and light source systems, this product is Risk Group 2, IEC 62471-5:2015.
- Possibly hazardous optical radiation emitted from this product.
- Do not stare at operating light source. Maybe harmful to the eyes.
- As with any bright source, do not stare into the direct beam.
The projector’s light source unit uses a laser
Laser Caution
This product belongs to CLASS 1 consumer laser product and complies with IEC
60825-1:2014, EN 60825-1:2014/A11:2021 and EN 50689:2021
Above laser caution is located on the bottom of this apparatus
Caution – Use of control or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.
- Notice is given to supervise children and to never allow them to stare into the projector beam at any distance from the projector.
- Notice is given to use caution when using the remote control for starting the projector while in front of the projection lens.
- Notice is given to the user to avoid the use of optional aids such as binoculars or telescopes inside the beam.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>