AZDOME JYX03 Dual Dash Cam User Manual
- June 9, 2024
- AZDOME
Table of Contents
Enjoy Your Smart Driving
Owner’s Manual
Hard-wire Kit
PARKING MODE WITH HARDWIRE KIT INTRODUCTION
When you using 3-lead Kit as power supply for dash cam, you can choose this
function.
Hard-wire kits, there are 3 wires that need to be connected:
- A RED wire (ACC), needs to connect with Fuse Box ACC, which can make the dash cam auto power on&off when the vehicle is on&off.
- A YELLOW wire (BAT+), needs to connect with constant fuse, which can provide power to dash cam even when the vehicle is off.
- A BLACK wire (GND), needs to connect with metal bolt or screw, which can prevent electric shock.
NOTE: The Parking Mode will ONLY work with the 3-wire Hard-wire Kit installed.
FUSE TAPS
Fuse sizes and the type of Fuse Taps vary depending on your vehicle, please
check your Fuse Box to see what type of fuse tap your vehicle requires. There
are 4 variations of the add-a-fuse that we carry:
ACZ(micro2), ACS(mini), ACN(LP-mini) and ACU(ATO) as photos below (2 Needed
Per Vehicle).
INSTALLATION
Step 1: Locate Your Fuse Box
Consult your car owner’s manual for the location of the fuse box. Depending on
the model of your vehicle, you may need to remove some trim or open some
panels to gain access to the fuses.
Step 2:
Connect the Yellow Wire of the Hard-wire Kit with one type of Fuse Taps that
your vehicle requires.
Step 3:
Locate the Fuse Box and find a Constant Fuse Slot in it.(Constant Fuse Slot
always has power even when the ignition is off.)
Use a circuit tester to test which fuse is constant and which is ignition-
switched. The circuit tester will light up when poking into the port on top of
the constant fuse, vice versa for the ignition-switched fuse.
Step 4:
Remove the original Fuse in the Constant Fuse Slot and install it into the
Bottom Slots of the Fuse Tap.
Step 5:
Insert the same size of Fuse we provided into the Top Slots of the Fuse Tap.
Step 6:
Connect the Fuse Tap to the positive terminal of your Constant Fuse Slot.
Step 7:
Connect the Red Wire of the Hard-wire Kit to the positive terminal of the
ACC Fuse Slot in the Fuse Box. ACC Fuse Slot only has power when the ignition
is on.
Tip: The installation steps of the Fuses are the same with steps 4 and 5.
Step 8:
Crimp the Black Wire and screw it down to any non-coated metal bolt/screw in
your vehicle to ground it.
If a bad ground is chosen, it may cause your dash cam to restart when the
current is unable to flow consistently.
Step 9:
Connect the USB connector of the Hard-wire kit to the USB input of your dash
cam.
Step 10:
Once you’ve hooked up the power and ground, plug the kit into your camera and
start your vehicle to see if it works. If it works, you can run and tuck all
the wires in to your car, werecommend to tape or zip tying the excess wires
out of the way in your vehicle so it doesn’t block any access to your fuse
box.
TROUBLESHOOTING GUIDE
Reversed orientation of the accessory and ignition switched wires The dash cam will behave abnormally if the wires are switched and in some cases even result in battery drain. Please double check with your specific Hard-wire kit for the wire orientation and don’t go off other guides.
Add-A-Fuse Incorrectly Set Up
If you don’t put a fuse into the top fuse slot of the add-a-fuse, it will
not feed power to the Hard-wire kit.
Bad Ground
When an incorrect ground is used the camera won’t get power.
A loose or weak ground may result in restarting when the vehicle hits a bump.
WARRANTY & CUSTOMER SUPPORT
We provide 12-Month of limited warranty for your product from the date ofpurchase to be free from defects in materials and craftsman- ship. For questions, support, or warranty claims, contact us at service@azdome.hk with you Order Number. If you can provide the photos orvideo to show your problem we will be appreciated.
service@azdome.hk
Please scan the QR code to contact us on WhatsApp
https://drive.google.com/file/d/1t7T_MOanpZIHxzwBotnQNVTV-
t5iSj21/view?usp=sharing
KAKA GROUP LTD
www.azdome.hk
service@azdome.hk
Address : 1801-1808, HaiYun Building, No. 468, Minzhi Avenue,
Longhua New District, Shenzhen, China. 518000, CN
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>