GOLDEN LIGHTING 3306-1W BLK-CLR Orwell 1-Light Wall Sconce Instruction Manual
- June 12, 2024
- GOLDEN LIGHTING
Table of Contents
GOLDEN LIGHTING 3306-1W BLK-CLR Orwell 1-Light Wall Sconce
Product Information
The product is a lighting fixture manufactured by Golden Lighting. It is available in the model number 3306-1W BLK-CLR. The fixture is designed to provide functional and stylish lighting for various spaces in your home.
Product Usage Instructions
Pendants & Linear Pendants Above a Kitchen Island
To properly install pendants or linear pendants above a kitchen island, follow these steps:
- Center a linear pendant over the island.
- If using hanging pendants, use one pendant for every 24 inches of the island.
- The fixtures should hang at least 30 inches above the countertop.
Pendants & Chandeliers Above a Dining Room Table
To install pendants or chandeliers above a dining room table, follow these steps:
- The fixtures should hang at least 30 inches above the table.
- Use a fixture that is 12 inches narrower than the width of the table.
Pendants and Chandeliers in Open Areas
When installing pendants or chandeliers in open areas, follow these guidelines:
- The bottom of the fixture should hang at least 7.5 feet from the floor.
- Ensure there is enough clearance for any opening doors.
General Tips for Lighting in Your Space
To achieve the best lighting in your space, consider the following tips:
- Layer your lighting to have both task and ambient lighting.
- Coordinate fixtures like sconces, flush mounts, and pendants to meet your layered lighting needs and desired aesthetic.
- Install the lights with dimmers to control the level of light output.
For more information and expert lighting advice, visit www.GoldenLighting.com.
Thank You for Choosing Golden Lighting for Your Lighting Needs!
-
Pendants & Linear Pendants Above a Kitchen Island
Center a linear pendant over the island. If hanging pendants, use one pendant for every 24″ of island. Fixtures should hang at least 30″ above the countertop. -
Pendants & Chandeliers Above a Dining Room Table
Fixtures should stay at least 30″ above the table. Use a fixture that is 12″ narrower than the width of the table. -
Pendants and Chandeliers in Open Areas
The bottom should hang at least 7.5 feet from the floor. Allow clearance for any opening doors.
We appreciate your business and hope you love your new light!
Great lighting can add value and enhance the look of your home. To ensure the
best lighting in your space, remember to layer your lighting. This ensures
that your space will have both task and ambient lighting. Coordinating
fixtures like sconces, flush mounts, and pendants can help you meet your
layered lighting needs and reinforce your desired aesthetic. Install the
lights with dimmers that allow you to control the level of light output at any
given moment.
Get function and style! Browse our site for coordinating lights and expert
lighting advice. To help create the perfect look, visit
www.GoldenLighting.com.
Love your light and want to show it off?
Follow us, share a picture, and tag us on Social…
- @GoldenLighting
- @GLFixtures
- @GoldenLighting1
- @GoldenLighting.
How to Identify the Fixture’s Wires
For Customer Service, contact the place of purchase to arrange for replacement parts.
IMPORTANT:
- All installation work should be done by accredited professional.
- Shut off power supply at fuse or circuit breaker!
- Use only the specified bulbs. Do not exceed the maximum wattage!
Assembly Instructions:
PREPARING FOR INSTALLATION
Carefully remove the new fixture from the carton as well as the yellow bag
that holds all of the parts. See the important notes above. Shut off power
at the circuit breaker and remove old fixture from wall, including the old
mounting strap. 1. Mounting strap (B) contains several pairs of threaded
holes. Find the pair of holes that matches the spacing of the holes on the
junction box and your fixture’s backplate. Two sets of mounting screws (A & D)
should be attached to the mounting strap (B). You may need to tighten nuts (C)
that hold mounting screws (A) in place. 2. Pull the house wires through the
center of the mounting strap (B). Place mounting strap (B) over the junction
box so that mounting screws (A) are horizontal, and in alignment with the hole
locations on the backplate (F). Secure mounting strap (B) to the junction box
with mounting screws (D) and a screwdriver. Tighten the screws securely.
ASSEMBLING THE FIXTURE
No Assembly Required – This item arrives assembled and ready for installation.
Please proceed to the next step.
CONNECTING THE WIRES
3. Have an assistant support the fixture’s weight while completing the
wiring. Refer to the wiring diagram and attach the fixture’s wires to the
power supply wires from the junction box. Attach the fixture’s wires to the
power supply wires from the junction box. Connect Hot to Hot (transparent wire
with black inner thread, black, or smooth wire) Neutral to Neutral
(transparent wire with white inner thread, white, or ribbed wire), and Ground
to Ground (transparent wire with green inner thread, green wire, or copper).
Twist the ends of the wire pairs together, and then twist on a wire connector.
Make sure all twists are in the same direction. If there is no house ground
wire coming from the junction box, locate ground screw (E) on the mounting
bracket/mounting strap and wrap the fixture’s ground wire around the ground
screw. Use a screwdriver to tighten the top of ground screw (E) onto the wires
and into the mounting bracket/mounting strap. Tuck the wires into the junction
box.
FINISHING THE INSTALLATION
4. Place backplate (F) over mounting screws (A) so that they protrude through
the holes in the front of the backplate (F). Thread deco nuts (G) onto the
exposed threads of mounting screws (A). Twist until the backplate (F) of the
fixture is snug against the wall. 5. Secure spider (I) to shade (L) with
screws (K) and decorative cap (J). Carefully slide assembled shade (L) over a
socket (H) and secure the shade in place with socket ring (M). Twist a light
bulb into sockets (H) in accordance with the fixture’s specifications. Do not
exceed the maximum wattage. Your installation is now complete. Turn on the
power and test the fixture.
Get help, quick tips, and explore curated content
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>