S S REGELTECHNIK ALTM2-EtherCAT P Surface Contact Temperature Measuring Transducer Pipe Instruction Manual

6000-3840-0000-1XX 38400-2022 V101 05 ⁄ 2022
THERMASGARD® ALTM2 – EtherCAT P

Operating Instructions, Mounting & Installation

Surface-contact temperature measuring transducer ⁄ pipe surface-contact sensor, with detached sensor, incl. strap, Bluetooth-enabled, with EtherCATP port

Dimensional drawing

M8-plug-in connector
EtherCATP-encoded
High-performance encapsulation against vibration, mechanical stress and humidity

PERFECT SENSOR PROTECTION

Networkable surface-contact temperature measuring transducer (detached version) THERMASGARD® ALTM2 – EtherCATP with M8 plug-in connector (EtherCATP- encoded), Bluetooth-enabled, in an impact-resistant plastic housing with quick-locking screws, optionally with ⁄ without display and bar graph, cable sensor with pipe feeder, incl. strap. The pipe surface-contact sensor is used to detect the temperature on lines, pipes (e.g. cold and warm water) or on heating sections for heating control. The sensor is factory-calibrated. EtherCATP-enabled measuring transducer for industrial requirements with maximum reliability: includes easy PLC integration using the device’s ESI configuration file, diagnostics (such as communication failure counter), advanced settings options, access to historical data (min / max) and estab- lishing the sensor’s service interval. Optionally with large illuminated display (3-line, customised programming in the 7-segment and dot-matrix range) and bar graph (7-digit, LEDs freely configurable) for graphical display, e.g., as a traffic light indicator.

TECHNICAL DATA

L=50mm
Sensor cable:| silicone, SiHF, 2 x0.25 mm2; cable length (KL) =1.5m (other lengths and jacket materials, e.g. PTFE or glass fibre with steel mesh, available on request)
Housing:| Plastic, UV-resistant, polyamide material, 30% glass-globe reinforced, with quick-locking screws (slotted/Phillips head combination), colour traffic white (similar to RAL 9016), housing cover for display is transparent!
Dimensions:| 126 x 90 x 50mm (Tyr 2)
Cable connection:| M8 plug-in connector, EtherCATP-encoded
Process connection:| Endless strap with metal tightener (included in delivery scope), 0=13-92mm 0/4-31, L=300mm
Ambient temperature:| Measuring transducer —30~70°C
Permitted humidity:| <95% r. H., non-precipitating air
Protection class:| III (according to EN 60730)
Protection type housing:| IP54 (according to EN 605291
Protection type sensor:| IP65 (according to EN 60529) sleeve humidity-tight (standard) IP68 (according to EN 60529) sleeve water-tight (optional)
Standards:| CE conformity, according to EMC Directive 2014/30/EU, according to RED 2014/53/EU
Equipment:| Display with illumination, 3-line, customised programming, cutout approx. W51 x H29mm, to display the actual temperature or a customised display value.
Bar graph, 7-digit, LEDs freely configurable, to graphically display the reading.

Surface-contact temperature measuring transducer with detached sensor, with EtherCATP port

Type/WG02| Measuring Range Temperature| Sensor| Output| Bar graph Item No. Display
---|---|---|---|---
ALTM2•ECATP xx| | | |
ALTM2-ECATP| -50…-1-150°C| Pt1000| EtherCATP| 2001-2171-9100-001
ALTM2-ECATP LCD| -50…-1-150°C| Pt1000| EtherCATP| 2001-2172-9100-001

Extra charge: Protection type IP 68 (sensor sleeve watertight compound- filled) per running metre of connecting lead (silicone / PTFE / glass fibre) on request

ACCESSORIES

Use the EtherCAT interface to program the LCD display.
With only one output value selected, the display is static; with several values selected, the display is cyclical with one after the other. In the first line the value is displayed and in the second line the corresponding unit. The third line is empty by default if there are no customised inputs.
The entire display in the 7-segment range as well as in the dot-matrix range can be customised.
When the supply voltage is applied, the device performs a function test for the display and bar graph.
This takes approximately 30 seconds, after which the device is ready for operation.
In the absence of a bus connection to the device, the message “ERR no link” appears in the display.

The status LEDs are next to the cable connection.

Installation and Commissioning

Notes regarding mechanical mounting and attachment:
Mounting shall take place while observing all relevant regulations andstandards applicable for the place of measurement (e.g. such as weldinginstructions, etc.). Particularly the following shall be regarded:
– VDE ⁄ VDI directive technical temperature measurements, measurement set – up for temperature measurements.
– The EMC directives must be adhered to.
– It is imperative to avoid parallel laying of current-carrying lines.
– We recommend to use shielded cables with the shielding being attached at one side to the DDC ⁄ PLC.
Before mounting, make sure that the existing thermometer‘s technicalparameters comply with the actual conditions at the place of utilization, in particular in respect of:
– Measuring range
– Permissible maximum pressure, flow velocity
– Oscillations, vibrations, shocks are to be avoided (< 0.5 g)
– Ensure not to kink or squash the sensor element

SAFETY REGULATIONS

These devices shall only be used for their intended purpose. Respective safety regulations issued by the VDE, the states, their control authorities, the TÜV and the local energy supply company must be observed. The buyer has to ensure adherence to the building and safety regulations and has to avoid all dangers of any kind. We do not assume any warranty for faults or damages arising or resulting from improper use of our equipment or from non-observance of operating instructions. These instruments must be installed by authorised specialists only!
Preferably shielded cables should be used in order to prevent damages ⁄ errors. It is imperative to avoid laying parallel with current-carrying lines.
EMC directives must be adhered to.
Notes on commissioning:
This device was calibrated, adjusted and tested under standardised conditions. When operating under deviating conditions, we recommend performing an initial manual adjustment on-site during commissioning and subsequently at regular intervals.
Commissioning is mandatory and may only be performed by qualified personnel!
If the sensor element’s admissible load limits are exceeded, ensure to use an adequate support structure.

Important notes

Our “General Terms and Conditions for Business“ together with the “General Conditions for the Supply of Products and Services of the Electrical and Electronics Industry“ (ZVEI conditions) including supplementary clause “Extended Retention of Title“ apply as the exclusive terms and conditions.
In additionIn addition, the following points are to be observed:
– These instructions must be read before installation and putting in operation and all notes provided therein are to be regarded!
– A suitable weather and sun protection hood must be used when installed outdoors.
– Devices must only be connected to safety extra-low voltage and under dead- voltage condition.
To avoid damages and errors the device (e.g. by voltage induction) shielded cables are to be used, laying parallel with current-carrying lines is to be avoided, and EMC directives are to be observed.
– This device shall only be used for its intended purpose. Respective safety regulations issued by the VDE, the states, their control authorities, the TÜV and the local energy supply company must be observed.
The purchaser has to adhere to the building and safety regulations and has to prevent perils of any kind.
– No warranties or liabilities will be assumed for defects and damages arising from improper use of this device.
– Consequential damages caused by a fault in this device are excluded from warranty or liability.
– These devices must be installed and commissioned by authorised specialists.
– The technical data and connecting conditions of the mounting and operating instructions delivered together with the device are exclusively valid.
Deviations from the catalogue representation are not explicitly mentioned and are possible in terms of technical progress and continuous improvement of our products.
– In case of any modifications made by the user, all warranty claims are forfeited.
– This device must not be installed close to heat sources (e.g. radiators) or be exposed to their heat flow.
Direct sun irradiation or heat irradiation by similar sources (powerful lamps, halogen spotlights) must absolutely be avoided.
– Operating this device close to other devices that do not comply with EMC directives may influence functionality.
– This device must not be used for monitoring applications, which serve the purpose of protecting persons against hazards or injury, or as an EMERGENCY STOP switch for systems or machinery, or for any other similar safety-relevant purposes.
– Dimensions of housing or housing accessories may show slight tolerances on the specifications provided in these instructions.
– Modifications of these records are not permitted.
– In case of a complaint, only complete devices returned in original packing will be accepted.
These instructions must be read before installation and commissioning and all notes provided therein are to be regard!
© Copyright by S+S Regeltechnik GmbH
Subject to errors and technical changes. All statements and data herein represent our best knowledge at date of publication. They are only meant to inform about our products and their application potential, but do not imply any warranty as to certain product characteristics. Since the devices are used under a wide range of different conditions and loads beyond our control, their particular suitability must be verified by each customer and/or end user themselves. Existing property rights must be observed. We warrant the faultless quality of our products as stated in our General Terms and Conditions.

S+S REGELTECHNIK GMBH
THURN-UND-TAXIS-STR. 22
90411 NÜRNBERG ⁄ GERMANY
FON +49 (0) 911 ⁄ 5 19 47-0
mail@SplusS.de
www.SplusS.de

Documents / Resources

| S S REGELTECHNIK ALTM2-EtherCAT P Surface Contact Temperature Measuring Transducer Pipe [pdf] Instruction Manual
ALTM2-EtherCAT P Surface Contact Temperature Measuring Transducer Pipe, ALTM2-EtherCAT P, Surface Contact Temperature Measuring Transducer Pipe, Temperature Measuring Transducer Pipe, Measuring Transducer Pipe, Transducer Pipe
---|---

References

• S+S Regeltechnik | Ihr sensorik Partner

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>