ideal lux 8I238104 Eris-1 Pendant Light Small Instruction Manual

ideal lux 8I238104 Eris-1 Pendant Light Small

Product Specifications

• Model: Eris-1 SP1
• Power: E27 max 1 x 42W
• Input Voltage : 220-240V, 50/60Hz
• Color Options : BIANCO (8021696238104), NERO (8021696249056)

Product Usage Instructions

Installation

1. The lighting fitting should be installed by a qualified electrician.
2. Follow the assembly instructions by reading the numerical progression provided in the manual.

Safety Instructions

1. Always disconnect the power supply before starting installation or maintenance.
2. Use appropriate mounting accessories such as screws and plugs suitable for the material.
3. Do not look directly into the light source.

Maintenance and Care

1. If the lamp does not turn on, replace the fuse.
2. Do not disassemble the light source with LEDs.
3. Ensure proper grounding as per safety class requirements.

Suspension lamp

• E27 max 1 x 42W / 220~240V 50/60Hz
• 8021696238104 BIANCO
•  8021696249056 NERO

DIMENSIONS

FEATURES

ASSEMBLY INSTRUCTIONS

• FOLLOW THE ASSEMBLY INSTRUCTIONS BY READING THE NUMERICAL PROGRESSION
• THE LIGHTING FITTING SHOULD BE INSTALLED BY A QUALIFIED ELECTRICIAN
• THE SAFETY AND RELIABILITY ARE GUARANTEED ONLY WHEN INSTALLATION INSTRUCTIONS ARE PROPERLY FOLLOWED. PLEASE KEEP THIS INSTRUCTION SHEET FOR FUTURE REFERENCE.

SAFETY INSTRUCTIONS

1. This fitting is produced and tested in accordance with the strictest European safety standards(EN 60.598-1).
2. This fitting cannot be disposed of as household waste. For disposal information ask the local authorities about how to collect it.
3. As indicated by specific regulations, the lighting fitting should be installed by a qualified electrician.
4. If the external wire is damaged it has to be replaced exclusively by the manufacturer, distributor or by a qualified electrician.
5. Always isolate power before commencing installation, maintenance or repair.
6. The luminaire contains certain parts which can be very hot.
7. Each material requires specific mounting accessories. Use screws and wall plugs suitable for the material to which they are fastened. Those included may be unsuitable.
8. Always tighten the screws firmly to avoid contact problems.
9. This fitting should only be installed indoors
10. Luminaires not suitable for recessed on normally flammable surfaces.
11. Luminaire not suitable for direct mounting on normal flammable surfaces.
12. This fitting is only suitable for fixing to the ceiling.
13. This fitting is only suitable for fixing to the wall.
14. The weight of the lamp has to be supported by the chain. Adjust the length of the electric wire so that it is longer than the chain.
15. Only use lamps which do not exceed the maximum specified wattage.
16.  Always observe the minimum distance between the lamp and the surface being lit, as shown inthe icon. The lamp can cause a fire if the minimum distance is not observed.
17. Auto-protected bulb. Only use bulbs marked with this symbol. Halogen bulbs get very hot. Waituntil they cool down before replacing.
18. Cracked or broken safety glass has to be replaced immediately. Use only manufcturer approvedparts complying with regulations.
19. Light source with not-substitutable light emitting diode (LED). Do not disassemble the productsince the diodes can damage the eyes. Do not immerse in water. Wipe with a damp cloth. Donot use solvents or strong detergents.
20. This fitting is equipped with a fuse. If the lamp is out of order, replace the internal fuse.
21. Class | Electrical safety is guaranteed by the main insulation and an additional protective conduc-tor (earthing) connected with the metal frame of the lamp. Earthing is obligatory.
22. Class ll Electrical safety guaranteed by the main insulation and a double or reinforced insulation.Earthing not necessary.
23. Class lll Electrical safety guaranteed by very low power supply (less than 50 Volt). Earthingexcluded.
24. Not protected.
25. Protected against solid objects greater than 50 mm.
26. Protected against solid objects greater than 12 mm.
27. Protected against solid objects greater than 2,5 mm,
28. Protected against solid objects greater than 1mm.
29. Dust protected.
30. Totally protected against dust infiltration.
31. Not protected.
32. Protected against vertically falling water drops.
33. Protected against water drops falling with a maximum angle of 15° to the vertical axis.
34. Protected against rain.
35. Protected against splashing water.
36. Protected against water jets.
37. Protected against strong water jets,
38. Protected against temporary immersion.
39. Protected against prolonged immersion
40. Luminaire not suitable for covering with thermally insulating material.
41. Caution, risk of electric shock.
42. Do not stare at the operating light source.

IDEAL  LUX s.r.l.

• Via Taglio Destro 32
• 30035 Mirano (VE) Italy
• www.ideal-lux.com

FAQS

Q: Can the LED light source be replaced?

A: No, the LED light source is non-replaceable. Do not attempt to disassemble it.

Q: What should I do if the lamp does not turn on?

A: Check and replace the fuse if needed. If the issue persists, contact a qualified electrician for further assistance.

Q: Is grounding mandatory for this product?

A: Yes, grounding is mandatory as per safety class requirements to ensure electrical safety.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>