Baseus WXHW02 Milky Way Electric Bracket Wireless Charger User Manual
- June 6, 2024
- Baseus
Table of Contents
Baseus Milky Way Electric Bracket
Wireless Charger
Operation Manual
Please read the instruction manual carefully before using the product and keep it with proper care.
Production information
Thank you for purchasing our products. This is a vehicle air outlet bracket with An intelligent device integrating car holder and wireless charging. Please read the operation manual carefully before using the product and the manual shall be properly kept in future licenses.
Specifications and parameters
Model: WXHWO2
Input: 5V-2A/ 9V-2A / 12V-1.67A(MAX)
Frequency: 110-205Klu Conversion efficiency >70% (M in)
Charging distance: 45mm
Product dimensions: 117 x 117x 125mm
Applications: Mobile phones with wireless charging function or external
wireless recharging receivers
Note : The above parameters are obtained from actual measurements. Actual
parameters may vary due to products or other factors.
Operation instructions
- Press the spring on the rear clamp of the product to make it tightly clamp the air outlet; adjust a proper angle, and the two legs of the clamp shall lean against the lower of the air outlet.
- Insert the charging cable into the jack at the bottom of the bracket, and the product will automatically open; the bracket gravity induction will lock up a mobile phone after it is placed on the bracket, and charging for the mobile phone will be started.
- If the charging is not successful after placing a mobile phone on it, please inspect whether there is metal on the back of the mobile phone; or the bracket bottom needs to be adjusted to make the wireless charging area align with that of the product LED indication: Standby: blue light and green light flash alternately; Charging green light flashes; Fully charged: green light keeps on; Foreign body, blue and green flash in turn rapidly.
Instructions
- When using the product, please use any adapter that supports QC2.0/QC3.0, with output voltage 5V 2A/9V 2A/12V 1.67A.
- No metal objects, such as metal plate, ring, or metal protective shell, can be placed on the contact surface during charging;
- In case of interrupted charging or a seriously high temperature during charging, the possible cause is that the receiving coil of the mobile phone fails to completely align with the wireless charging coil. Please cool the mobile phone, and then conduct correct alignment.
- The product is equipped with overcurrent and overvoltage protection. It may be turned off or lower output power if it is not properly used. Please inspect whether the equipment has any abnormal condition or it is properly used.
- The operating temperature range shall be kept at 0-30°C. Do not put it into water, fire or any environment with extremely high temperature (>40°C) or extremely low temperature (<-20°C). Keep it out of reach of children.
- Please use a dry and soft cloth to clean the surface. Chemicals, soap or detergent shall not be used.
- The product may be damaged or its service life may be reduced due to improper operation or placement, and we or the manufacturer will not be responsible for any responsibility hereof.
- Quick charging may not be available for iPhones due to the following conditions. As a result, the charging speed may be slower.
a) The battery level of any iPhone is larger than 80%;
b) iOS version is below 11.1.2;
c) Mobile phone temperature is higher than 35°C.
http://weixin.qq.com/r/JnXp8RfE6kqVrVOS9yA0
Designed by Baseus
Made in China
Shenzhen Times Innovation Technology Co., Ltd.
Add: 5th Floor, Building B, Baseus Intelligence Park,
No.2008, Xuegang Rd, Gangtou Community,
Bantian Street, Longgang District, Shenzhen
Executive Standard: Q/SSCZ 021-2020
Hotline: +86-4000-712-711
Website: www.baseus.com
www.baseus.com
Copyright©2010-2020Shenzhen Times Innovation Technology Co., Ltd.
All Rights Reserved
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
The equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. During the operation of device a distance of 15cm
surrounding the device and 20 cm above the top surface of the device must be
respected.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>