cell2 160607M53 Light Instruction Manual

cell2 160607M53 Light

Product Information

The product is a light assembly designed for mounting on vehicles. It consists of a lighthead and a snap-on bezel. The light assembly is capable of producing various flash patterns and can be synchronized with other lightheads. The product comes with double-sided adhesive foam for mounting and sheet metal screws for bezel installation.

Installation

To install the light assembly, follow these steps:

1. Remove the Corner/Head/Tail light from the vehicle.
2. Select a location to mount the lighthead.
3. Drill a 1 inch diameter cut-out on the light assembly.
4. Insert the lighthead through the double-sided adhesive foam and the cut-out, then press firmly for 1 minute. Make sure to clean the mounting surface thoroughly with alcohol before mounting.
5. Apply silicone (user-supplied) for better seal. Note that the heatsink should not be covered with silicone to avoid damage and voiding the warranty.

Warning: Do not cover the heatsink with silicone. This may cause damage to the product and void the warranty.

Note: Lighthead mounting location may vary depending on the design of the vehicle light assembly.

Operation

To operate the light assembly, follow these instructions:

For Simultaneous or Alternating Flash:

1. Apply +VDC (fuse @ 2A) to the RED and YELLOW wires simultaneously to enter Grouping mode. The lighthead will display short flashes (single or double).
2. Remove the YELLOW wire from +VDC and momentarily apply it to +VDC to change Groups. Heads in the same Group will flash together. Group1 Heads will alternate with Group2 Heads.
3. Disconnect power to save and exit Grouping mode.

For Flash Patterns:

Momentarily apply +VDC to the YELLOW wire:

• Once for the next pattern.
• Quickly three times for FP#1.

Note: This unit may not be factory set at FP#1.

Bezel Mount Installation

To install the snap-on bezel, follow these steps:

1. Use the mounting foam to mark wire and screw holes before drilling.
2. Carefully drill the marked holes accordingly.
3. Insert lighthead wires through the mounting foam and into the wire hole.
4. Secure the lighthead with the supplied sheet metal screws.
5. Mount the snap-on bezel onto the lighthead. Make sure to use the foam when mounting the lighthead.

Note: Avoid multiple mounting and removal of the bezel to prevent a loose fit.

Light Assembly Installation

1. Remove the Corner/Head/Tail light from the vehicle.
2. Select a location to mount the lighthead.
3. Drill an 1 inch diameter cut-out on the light assembly.
4. Insert the lighthead through the double-sided adhesive foam and the cut-out thenpress firmly for 1 minutes. (Please ensure that the surface is cleaned thoroughly withalcohol before mounting.)
5. Apply silicone (user-supplied) for better seal.

WARNING: DO NOT cover the heatsink with silicone.
This may cause damage to the product and void the warranty.

NOTE: Lighthead mounting location may vary depending on the design of the vehicle light assembly.

OPERATIONS

Not applicable when mounting with Double-sided Adhesive Foam

• To +VDC (fuse @ 2A)…………..RED
• To Chassis Ground………….BLACK
• For Synchronization………YELLOW
  Connect YELLOW wires of all heads together for synchronization
  (All heads must be set at the same pattern)

For Simultaneous or Alternating Flash:

1.  Apply +VDC to RED and YELLOW wires simultaneously to enter Grouping mode; light head will display short (single or double) flashes:
   • Single flash = Group1．Double flash = Group2
2. Remove the YELLOW wire from +VDC and momentarily apply to +VDC to change Groups: ．Heads in the same Group flash together.
   • Group1 Heads alternate with Group2 Heads.
3. Disconnect power to save and exit Grouping mode.

For Flash Patterns:
Momentarily apply +VDC to YELLOW wire:

• once for next pattern
• quickly three times for FP#1

NOTE: This unit may not be factory set at FP# 1.

Bezel Mount Installation

1. Use the mounting foam to mark wire and screw holes before drilling.
2. Carefully drill marked holes accordingly.
3. Insert lighthead wires through the mounting foam and into the wire hole.
4. Secure the lighthead with supplied sheet metal screws.
5. Mount the snap-on bezel onto the lighthead.
   NOTE: Make sure to use the foam when mounting the lighthead.

BEZEL REMOVAL

1. Apply pressure on both sides marked with triangle.
2. Lift the bezel to remove.

NOTE: Avoid from multiple mount and removal of the bezel to prevent loose fit.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>