KEYENCE LBEE5HY1MW WiFi Module Installation Guide
- June 12, 2024
- KEYENCE
Table of Contents
KEYENCE LBEE5HY1MW WiFi Module Installation Guide
LBEE5HY1MW Installation Manual
FCC ID of this product is as follows.
FCC ID: RF41675A
IC No. of this product is as follows.
IC: 5798A-1675A
Land Pattern (Recommended)
• To avoid the short-circuit between the side shielding and a solder on the module land after the reflow, please locate the module land at 0.2mm away from module outline as above figure.
PIN Layout
Antenna
- Please perform the antenna design that followed the specifications of the antenna.
- About the signal line between an antenna and a module
It is a 50-ohm line design.
Fine tuning of return loss etc. can be performed using a matching network.
However, it is required to check “Class1 change” and “Class2 change” which the
authorities define then.
The concrete contents of a check are the following three points.
- It is the same type as the antenna type of antenna specifications.
- An antenna gain is lower than a gain given in antenna specifications.
- The emission level is not getting worse.
■ 50-ohm line(microstrip line length)
Recommended antenna design
This Antenna Specification is based on Keyence’s requirement..
Model name LBEE5HY1MW
Appearance
Recommended antenna characteristics
Supply Voltage
- Surface temperature of the shield case Functionality is guaranteed but specifications require derating at extreme temperatures
- VIO don’t influence the RF characteristic. Tolerance of 1.8V and 3.3V is ±10%.
Theory of Operation-Channel List
Theory of Operation-Software Security and Channel List
- This specification is limited to use in the above frequency bands and modes.
Notes: End users cannot modify the software because F/W & driver are installed in device.
Theory of Output Power List
This specification is limited to use with the following output power settings.
Limited output power setting. [dBm]
LBEE5HY1MW User Manual for FCC
- Regarding FCC modular approval of LBEE5HY1MW
Model Name: LBEE5HY1MW
FCC ID: RF41675A
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Since this module is not sold to general end users directly, there is no user
manual of module.
For the details about this module, please refer to the specification sheet of
module.
This module should be installed in the host device according to the interface
specification (installation procedure).
- The following information must be indicated on the host device of this module.
Contains Transmitter Module FCC ID: RF41675A
or
Contains FCC ID: RF41675A
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
*If it cannot be described on the host product, it must be listed on both the host product manual and on the host product package or removable label.
- The following statements must be described on the user manual of the host device of this module;
FCC CAUTION
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
Compliance with FCC requirement 15.407(c)
Data transmission is always initiated by software, which is the passed down
through the MAC, through the digital and analog baseband, and finally to the
RF chip. Several special packets are initiated by the MAC. These are the only
ways the digital baseband portion will turn on the RF transmitter, which it
then turns off at the end of the packet. Therefore, the transmitter will be on
only while one of the aforementioned packets is being transmitted. In other
words, this device automatically discontinue transmission in case of either
absence of information to transmit or operational failure.
Frequency Tolerance: ±20 ppm
This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.
- When installing it in a mobile equipment. Please describe the following warning to the manual.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines. This equipment should be installed and operated keeping the radiator at least 20cm or more away from person’s body.
- When installing it in a portable equipment. Please describe the following warning to the manual.
The available scientific evidence does not show that any health problems are associated with using low power wireless devices. There is no proof, however, that these low power wireless devices are absolutely safe. Low power Wireless devices emit low levels of radio frequency energy (RF) in the microwave range while being used. Whereas high levels of RF can produce health effects (by heating tissue), exposure of low-level RF that does not produce heating effects causes no known adverse health effects. Many studies of low-level RF exposures have not found any biological effects. Some studies have suggested that some biological effects might occur, but such findings have not been confirmed by additional research. LBEE5HY1MW has been tested and found to comply with FCC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines.
It is necessary to take a SAR test with your set mounting this module (except
to use only Bluetooth V5.0(BDR/EDR/LE)).
Class II permissive change application is necessary using the SAR report.
Note)
Portable equipment: Equipment for which the spaces between human body and
antenna are used within 20cm.
Mobile equipment: Equipment used at position in which the spaces between human
body and antenna exceeded 20cm.
LBEE5HY1MW User Manual for ISED
PMN: LBEE5HY1MW
HVIN: LBEE5HY1MW
IC Number: 5798A-1675A
Since this module is not sold to general end users directly, there is no user
manual of module.
For the details about this module, please refer to the specification sheet of
module.
This module should be installed in the host device according to the interface
specification (installation procedure).
- The following information must be indicated on the host device of this module.
Contains IC: 5798A-1675A
- The following statements must be described on the user manual of the host device of this module;
This device complies with Industry Canada’s applicable licence exempt RSSs. Operation is subject to the following two conditions:
- This device may not cause interference; and
- This device must accept any interference, including interference that may cause undesired operation of the device.
*If it is difficult to describe this statement on the host product due to the size, please describe in the User’s manual.
- In case of the final product which can be carried around to outdoor.
The following indication is necessary to the final product.
When the AP function is used in W52;
At the time of a channel setting of W52, please indicate “for indoor use
only”. During connecting, please show the channel number which connects.
And please indicate that the end user may find out “for indoor use only
channel”.
When the STA function is used in channel 52, 54, 58, at the time of the
channel 52 or 54 or 58 setting, please indicate “for indoor use only channel”.
During connecting, please show the channel number which connects.
And please indicate that the end user may find out “for indoor use only
channel”.
If the antenna of the end product is removed, please describe the follow warning on the manual of the end product which contains this module.
This radio transmitter (IC Number: 5798A-1675A) identify the device by certification number or model number if Category II) has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.
: 2.4GHz Monopole Gain: +2.1 dBi
: 5GHz Monopole Gain: +3.5 dBi
- If the final product use the following frequency, please note that there is a limit.
For indoor use only (5150-5250MHz band and channel 52, 54, 58)
- The following statements must be described on the user manual of the host device of this module;
Data transmission is always initiated by software, which is the passed down through the MAC, through the digital and analog baseband, and finally to the RF chip. Several special packets are initiated by the MAC. These are the only ways the digital baseband portion will turn on the RF transmitter, which it then turns off at the end of the packet. Therefore, the transmitter will be on only while one of the aforementioned packets is being transmitted. In other words, this device automatically discontinue transmission in case of either absence of information to transmit or operational failure.
*If it is difficult to describe this statement on the host product due to the size, please describe in the User’s manual.
- When installing it in a mobile equipment. Please describe the following warning to the manual.
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment and meets RSS-102 of the IC radio frequency (RF) Exposure rules. This equipment should be installed and operated keeping the radiator at least 20cm or more away from person’s body.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>