Shenzhen Guanglihai Technology QC130 RGBW Remote Control Instruction Manual
- June 5, 2024
- Shenzhen Guanglihai Technology
Table of Contents
Guanglihai Technology QC130 RGBW Remote Control
Instruction Manual
Thanks for your purchase!
This manual describes the RGB white remote control used for the RGBW light
bulb. It can control the led lights in up to four different zones, change the
color, dim/brighten the lights, warm/cool white, and different programs. In
this manual, you will learn about:
Basic functions of the remote control:
Linking new lights to the remote control:
Grouping multiple lights:
Basic control functions:
(As is shown on the right picture )
Long press the ‘Master OW12one ON’ button, and you can get the white model.
Touch the color ring, you can get any color. And you can change the brightness
by the brightness ring +
Programs:
Program 1 ( RGBW Fade In Fade Out)
This program fades in and fades out the color red, green, blue, and white one
after another.
Program2( Color Flash)
In this program, red. green. blue, white yellow purple flash to change.
Program 3 ( Disco)
Different colors strobe and flash to change.
Program 4 (Red Color Ramp up and Flash)
In this program, the red color brightens from 0%-100% and shuts down, then
flashes three times.
Program 5 (Green Color Ramp up and Flash)
In this program, the green color brightens from 0%-i 00% and shuts down, then
lathes three times.
Program 6 (Blue Color Ramp up and Flash)
In this program, the blue color brightens from 0%-100% and shuts down, then
flashes three times.
Program 7( Color Change+ Flash)
Here several colors fade into each other and then flash randomly.
Program 8 ( Fade in and Fade out)
Here different colors fade into each other.
Program 9 (Strobe White)
Just white color flashes up.
TIPS:
To dim all RGBW lights at once or change the color, first press’ Master ON’.
To do this with individual fights, first press one ON’. Secondly, choose the
color or brightness according to the color ring or brightness ring.
Linking new lights to the remote controls:
- Choose which zone you want to assign the light( 1 to 4)
- Switch off the main power supply of the light in the selected zone with the main switch or pull the plug from the socket.
- Now switch on the light again and within 3 seconds shortly press one of the ‘Zone ON’ buttons one time on the remote control.
- When this link operation is successful, the light slowly blinks 3 times on and off.
Unlinking the lights:
- Check via the remote control to see which zone ( 1 to 4) is already linked to alight.
- Switch off the main power supply of the light with the main switch or pull the plug from the socket.
- Now switch on the light again and within 3 seconds press 5 times quickly and shortly on one of the ‘Zone ON buttons which you want to link.
- When this unlink operation is successful, the light quickly blinks 6 times on and off.
Grouping of several lights
You can add an endless number of lights to a zone on the 4-channel remote by
linking the lights to different zones. This way you are completely flexible in
creating different group combinations. Below you can see some grouping
examples.
We recommend using
rechargeable batteries for the remote controls. For that reason, we don’t
include ordinary batteries. We hope you appreciate our environmentally
friendly choices and they do not cause you any inconvenience.
FCC Statement
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications to this device not explicitly approved
by the manufacturer could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
RF Exposure Information
The device has been evaluated to meet general RF exposure requirements. The
device can be used in portable exposure conditions without restriction.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>