ETA423790000 Stormio Vacuum Cleaner User Manual

BASIC STRUCTURE OF THE APPLICATION MAIN CONTROL MENU
USER’S MANUAL FOR ETA SMART APPLICATION
STORMIO
ETA423790000

ETA423790000 Stormio Vacuum Cleaner

Dear customer,
Thank you for your confidence in the ETA brand products. This manual is destined for all owners of the ETA423790000 STORMIO vacuum cleaner, who want to use in full range its potential by means of ETA SMART Application. You can find here simple instructions and procedures how to work with your new robotic friend.

APPLICATION INSTALLATION

You can find this application in the database of Apple Store or Google Play, or can also use this QR code for quickening:

https://smartapp.tuya.com/ETArobotssmart

Download and install the application to your mobile phone (tablet).

COMPATIBILITY

Mobile phone (tablet) operation system| Android 7.0 and higher
IOS 11.0 and higher
Wi-Fi network| 2.4 GHz
security WPA1 and WPA2 (WPA2 is recommended)

ATTENTION
The appliance cannot be operated with Wi-Fi networks secured with IEEE 802.1X protocol (as a rule, company’s Wi-Fi networks).

CREATION OF ACCOUND

1

| | • Switch-on ETA SMART.
---|---|---

2

| | • Click on „Sign Up“.
• Afterward, it is necessary to confirm principles of personal data protection.
• Set an email of your user’s account.
• Then, click on „Get Verification Code“.

3

| | • After that, an individual verification code will be sent to your e-mail.

4

| | • Set a password and finish creation of your account.

5

| | • Login with this account to the application.

PAIRING OF APPLIANCES

1

| | • Connect your mobile phone (tablet) to your Wi-Fi network.
• Switch-on ETA SMART Application and login to your account.
• After that, click on „Add Device“ (or to „+” in the right upper corner).
---|---|---

2

| | • Select the „ETA 4237 Stormio“ vacuum cleaner.

3

| | • Enter your Wi-Fi network name and password.

4

| | • Inspect the robot vacuum and switch it on (where necessary).
• Wait until the device goes into standby mode (voice message will be issued).
• Afterwards click on „Next“.

5

| | • Press and hold the button on device´s control panel for approx. 5 seconds, until voice message „Mains connection configuration“ will be issued. This will reset the Wi-Fi module of the vacuum robot.
• Confirm successful reset.
• Then click on „Next“.

6

| | • Click on „Reconnect“, and then you will be automatically redirected to the list of Wi-Fi
networks available in your phone (tablet).
• Select the vacuum cleaner Wi-Fi network named „SmartLife-…“ and wait for connection with the vacuum cleaner.
Afterwards, „Internet may be unavailable” will appear, but it‘s all right. A mobile phone (tablet) is connected to the vacuum cleaner, and a pairing procedure will be performed in the next step. Now, return back to ETA SMART Application.

7

| | • Wait for a while until all three steps of the pairing procedure have been performed
correctly.

8

| | • In the end, the application will inform you about successful pairing.

REMARKS:

• Before pairing, we recommend that you fully charge the vacuum cleaner (or at least, 30% of the accumulator capacity).
• Follow attentively information and particular steps in the application.

MAP CREATION

1

| | • Place correctly the charging station in keeping with instructions in the manual
• After that, place the vacuum cleaner onto the charging station and wait until the
vacuum cleaner is fully charged.
---|---|---

2

| | • Make available all rooms, in which you want to clean up regularly (open the
doors and remove all obstacles, which could prevent the vacuum cleaner from
movement).
• Click on „Start“ on the main screen. You will be asked, how do you want to create
the map:
1. Automatic cleaning „Auto“ – the device xwill create the map while cleaning;
2. Function „Create New Map“ – the device will efficiently map accessible floor surface.

3

| | • No matter which mapping function you have chosen, wait until the device has
completed its working task (i.e. it has returned to its charging station).
• After that, you may save the map and continue to work with it.

4

| | • If you want to save a map, click on „Setting“ (in the right lower corner) on the
main screen.
• Select „Map management“ in menu.
• Then, click on „Save“ to save the map.
• In this menu, you can also carry out basic operations with the maps (store map,
delete map, map name, create new map, activate the map in the memory).

REMARKS:

• Save each map which you would like to use for a long time.
• We recommend using „Create New Map“ function for creation of a new map. In this case, the map can be better modified (e.g. keep out zones), thus allowing the robot vacuum to move only on the floor surface you want to clean at the next cleaning operation.
• In total, you can create an save up to 3 maps. This option may be used, especially, in case of multistage houses.

MAP MODIFICATION AND ADAPTATION

1

| | Automatic division of the map into rooms
• Correct map creation procedure or primary automatic („Auto“) cleaning having been
successfully completed, created map will be automatically segmented (Room1, Room2, Room3 etc…).
---|---|---

2

| | Possible map modifications in menu „Map editing“
Click on „Map editing“ on the main screen to perform the following changes:
• „Merging room“ (using this function, you can join 2 adjacent rooms);
• „Room segmentation“ (using this function, you can divide 1 room in 2 rooms);
• „Name“ (using this function, you can arbitrarily name rooms);

3

| | Combining rooms
• In the „Map editing“ menu, click on „Merging room“ and afterwards click on two adjacent rooms to select them.
• Consequently, click on „Merging room“ to confirm the selection and, thus, to join the
selected rooms.

4

| | Room segmentation
• In the „Map editing“ menu, click on „Room segmentation“ and afterwards click on
a room, which you want to divide.
• As soon as you select a room, a tool (vector) will appear in the map, with which you may divide the room in 2 parts. By shifting the edge points of the vector, select the place to be divided.
• Consequently, click on „Split“ to confirm the modification and, thus, to divide the
room.
• If the line segment is not visible, zoom in the map to obtain a better view.

5

| | Room name
• In the „Map editing“ menu, click on „Name“ and afterwards click on a room, the name
of which you want to change.
• Consequently, click on „Confirm“ to confirm the change and, thus, to change the room
name.

6

| | Restricted areas and virtual walls
• On the main screen, click on „Restricted areas“.
• You may set prohibited zones and virtual walls in this menu.

7

| | Restricted areas
It is possible to set 2 types of prohibited zones:
• „Area“ – full prohibition of the movement of the vacuum cleaner in this zone.
• „No mopping“ – no mopping can be used in this zone.
Addition of a restricted area:
• Click on the respective type of the prohibited zone in menu. You may replace a prohibited zone in the map or change its size with help of a finger.
• If you want to remove an inserted prohibited zone, click directly on it with a finger and then click on na „Cross“.
• Click on „Save“ to save the performed changes.

8

| | Virtual wall
• Switch over setting to „Wall“.
• After that, click on „Wall“.
• You may replace the inserted virtual wall in the map with a finger and modify it
variously.
• If you want to remove a virtual wall, click directly on it with a finger and then click on
„Cross“.
• Click on „Save“ to save the performed changes.

REMARKS:

• Having finished all necessary settings, save the map.
• In total, it is possible to insert up to 10 different restricted areas and 10 virtual walls.

LOADING OF A SAVED MAP

1

| | • On the main screen, click on „Setting“ (in the right lower corner).
• After that, select „Map management“ in menu.
---|---|---

2

| | • In the map list, choose the map you want to activate.
• Click on „Use map“ to activate the relevant map in the memory.

AUTOMATIC CLEANING

1

| | • On the main screen, click on „Auto“.
• After that, click on „Start“ to start cleaning.
• The vacuum cleaner will clean up systematically all the rooms in the map to which an access is enabled.
---|---|---

2

| | • Having finished the cleaning, the vacuum cleaner returns automatically to the charging station.

REMARKS:

• It is one of the most usable cleaning modes, when the vacuum cleaner cleans up the whole available area.
• Automatic cleaning may be also used with the mopping function. In this case, however, it is necessary to prevent the vacuum cleaner from driving onto a rug. If you have rugs in your house, you may use the prohibited zone function.

ROOM CLEAN-UP

1

| | • On the main screen, click on „Room cleaning“.
• Consequently, click on a room, w hich you want to clean up.
• After that, click on „Start“ to start cleaning.
---|---|---

2

| | • Having finished the cleaning, the vacuum cleaner returns automatically to the charging station.

REMARKS:

• Before using the cleaning mode, at first, it is necessary to create a map.
• One room or several rooms may be cleaned up within one cleaning.

AREA CLEANING

1

| | • On the main screen, click on „Zone cleaning“.
• Click on „Add cleaning zone“ to insert a zone into a map.
• You may freely shift a zone in the map and change its size.
• If you want to remove a zone, click directly on it with a finger and then click on „Cross“.
---|---|---

2

| | • Click on „Start“ to start cleaning.

3

| | • Having finished the cleaning, the vacuum cleaner returns automatically to the charging station.

REMARKS:

• Up to 10 different zones can be set for zonal cleaning.
• Within zonal cleaning, the vacuum cleaner cleans up all set zones.

SPOT CLEANING

1

| | • On the main screen, click on „Spot cleaning“.
• Click on a place in the map with a finger, where you want to perform local cleaning.
The point around of which local cleaning is to be performed will be shown in the map.
• After that, click on „Start“ to start cleaning.
---|---|---

2

| | • Having finished the cleaning, the vacuum cleaner returns automatically to the charging station.

REMARKS:

• Within local cleaning, the vacuum cleaner cleans a square around the set point with sizes of 1.5 x 1.5 m.

CLEANING ALONG THE WALLS

1

| | • The robot vacuum must be out of the charging station.
• Click on „Edge“ on the main screen.
• Then click on „Start“ to start cleaning.
---|---|---

2

| |

• After cleaning, the device will automatically return back to the charging station.

REMARKS:

• In order to allow activation of the function cleaning along the walls, the device must be placed out of the charging station.

SUCTION POWER SETTING

1

| | • On the main screen, click on „Suction Power“.
• Click on the required setting with a finger to select it. In total, there are 3 stages of
suction power.
---|---|---

REMARKS:

• You may adjust suction power in each of the cleaning modes.

MOPPING

1

| | • The mopping function can be used for all types of cleaning.
---|---|---

2

| | • To set mopping intensity, click on the „Water level“ icon and choose the required level.

REMARKS:

• To use the mopping function, it is necessary to install a mopping adapter on the vacuum cleaner according to the instruction for use.
• When using the mopping function, it is necessary to prevent the vacuum cleaner from driving onto a rug.

PLANNING OF CLEANING

1

| | • On the main screen, click on „Setting“.
• Afterwards, click on „Schedule cleaning“ in menu.
---|---|---

2

| | • There are 7 predefined cleanings in the menu.
• By clicking, you can adjust the individual cleanings as needed.

3

| | • Set time in the upper part.
• In the „Repeat“ menu, set days when you want to repeat cleaning.
• In the „Clean Type“ menu, set cleaning mode.
• Click on „Save“ in the right upper corner to save setting.

4

| | • Using switches, you may activate/deactivate particulars cleanings.
• If you want to modify one of the planned cleanings, click shortly on the corresponding cleaning with a finger.

REMARKS:

• If you use more than one maps (for example, in a multistage house), always make sure that you activate only those planned cleanings which belong to the corresponding actually-used map.
• If the device has been activated (i.e. it is cleaning/returning to the charging station), planned cleaning operation cannot be set.

REMOTE CONTROL

1

| | • On the main screen, click on „Setting“.
• Afterwards, click on „Remote control“ in menu.
• Now you may control the vacuum cleaner similarly as with a standard remote control panel.
---|---|---

FIND THE VACUUM CLEANER” FUNCTION

1| | • On the main screen, click on „Setting“.
• Afterwards, click on „Find a Robot“ in menu.and consequently confirm it by clicking on „Confirm“.
• After it, the vacuum cleaner will warn you acoustically to specify its position.
---|---|---

REMARKS:

• This function can be used, especially, if the vacuum cleaner gets jammed in whatever part of the house (for example, under furniture).

HISTORY OF CLEANINGS

1

| | • On the main screen, click on „Setting“.
• After that, select „Cleaning history“ in menu.
• By this, you will obtain simple review of the performed cleanings.
---|---|---

2

| | • Click on a particular cleaning in the list of cleanings in the history to see detailed information on the corresponding cleaning.

AUDIO WARNING VOLUME SETTING

1

| | • On the main screen, click on „Setting“.
• After that, select „Voice and volume“ in menu.
• Now you may set sound volume and language of the audio warnings or may fully switch-off them.
---|---|---

REMARKS:

• Audio warnings may be also switched-off in a certain moment by means of „Not disturb time“ (see Chapter 19. DO NOT DISTURB MODE).

DO NOT DISTURB MODE

1

| | • On the main screen, click on „Setting“.
• After that, select „Not disturb time“ in menu.
• Now you may set a time interval for switching-off audio warnings.
• To activate this mode, use a switch in the right upper corner.
---|---|---

MONITORING OF SERVICE LIFE OF COMPONENTS

1

| | • On the main screen, click on „Setting“.
• After that, select „Component life“ in menu.
• You may here easily obtain information on the service life of particular components of the vacuum cleaner (HEPA filter, side brushes, main brush).
---|---|---

2

| | • After the replacement of one of the components, it is necessary to reset it to start the deduction of percents from 100%.
• To do it, click on the corresponding component first.
• Then, click on „Confirm“ to confirm the reset.

REMARKS:

• The remaining service life of individual components will be shown as a percentage and also in minutes (how many percent/minutes remain).
• After the lapse of the service life of a component, we recommend that you replace this component to keep in the best way efficiency of suction and to prevent the vacuum cleaner from possible damage.

SETTING OF SHARING

1

| | • Click on the pencil symbol in the right upper corner of the main screen.
---|---|---

2

| | • Select „Share Device“ in menu.

3

| | • Click on „Add Sharing“.

4

| | • Click on „Share with the Account ETA Smart“.

5

| | • Select the country and enter the e-mail account the device should be shared with.
• Then click on „Done“. A message about sharing the robot vacuum will be sent to the e-mail account you have defined.

6

| | • To delete sharing, select the relevant account in the „Share device“ menu and click on this account.
• Then click on menu option „Unshare“.
• Click on „Confirm“ to confirm.

REMARKS:

• Users, with which you share your vacuum cleaner, may also control it, but have partially limited possibilities.
• A user, to whom you want to set sharing, has to create his/her own account in the ETA SMART application.

FIRMWARE UPDATE

1

| | The vacuum cleaner has software in its inner memory named Firmware. If a newer version
has been issued, it is necessary to update it.
• Click on the pencil symbol in the right upper corner of the main screen.
• Select „Device Update“.
---|---|---

2

| | If a new version is available, confirm update.
Having finished updating, place the vacuum cleaner into the charging station. The vacuum
cleaner has to be connected to a Wi-Fi network with available Internet connection.
• If you require to check automatically new available versions, you may switch-on the
„Automatic Updates“ option.

TROUBLESHOOTING

doesn’t help, restart your smart appliance.
The application doesn’t react at all, although was functioning well earlier.| Most probably, the situation is caused by a change, which has been performed in your phone (for example, installation of other applications, system update, etc.) or in the WiFi network. If you cannot solve the problem by returning your phone or Wi-Fi network to the state before changing, uninstall ETA SMART Application and install it again.
You do not succeed with pairing the vacuum cleaner and a Wi-Fi network.| Check the version of the operation system in your mobile phone and use only supported versions (Android 7.0 and newer; IOS 11.0 -and newer).
Use high-quality Wi-Fi router, which sufficiently covers your house.
During paring, keep your mobile phone sufficiently close to the vacuum cleaner (in a distance approx. 2 m).
For pairing of ETA423790000 STORMIO vacuum cleaner, proceed as shown in the instruction video (select relevant vacuum robot type at www.eta.cz/robot ).

https://smartapp.tuya.com/ETArobotssmart

References

• ETA - tady je doma
• Technická podpora robotických vysavačů | ETA - tady je doma
• Technická podpora robotických vysavačů | ETA - tady je doma

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>