GOLDEN LIGHTING 0309-FM Crawford 1 Light 12 inch Brushed Instruction Manual
- June 4, 2024
- GOLDEN LIGHTING
Table of Contents
GOLDEN LIGHTING 0309-FM Crawford 1 Light 12 inch Brushed Instruction Manual
Thank You for Choosing Golden Lighting for Your Lighting Needs!
Pendants & Linear Pendants Above a Kitchen Island
Center a linear pendant over the island. If hanging pendants, use one pendant
for every 24″ of island. Fixtures should hang at least 30″ above the
countertop.
Pendants & Chandeliers Above a Dining Room Table
Fixtures should stay at least 30″ above the table. Use a fixture that is 12″
narrower than the width of the table.
Pendants and Chandeliers in Open Areas
The bottom should hang at least 7.5 feet from the floor. Allow clearance for
any opening doors.
We appreciate your business and hope you love your new light!
Great lighting can add value and enhance the look of your home. To ensure the best lighting in your space, remember to layer your lighting. This ensures that your space will have both task and ambient lighting. Coordinating fixtures like sconces, flush mounts, and pendants can help you meet your layered lighting needs and reinforce your desired aesthetic. Install the lights with dimmers that allow you to control the level of light output at any given moment.
Get function and style! Browse our site for coordinating lights and expert lighting advice. To help create the perfect look, visit www.GoldenLighting.com.
Love your light and want to show it off?
Follow us, share a picture, and tag us on Social…
@GoldenLighting
@GLFixtures
@GoldenLighting1
@GoldenLighting
Assembly Instructions: 0309-FM
How to Identify the Fixture’s Wires
Hot: Smooth, Black, or Transparent with Black Inner Thread
Neutral: Ribbed, White or Transparent with White Inner Thread
Ground: Copper, Bare Metal, Green, or Transparent Inner Thread
For Customer Service, contact the place of purchase to arrange for replacement parts.
IMPORTANT:
- All installation work should be done by accredited professional.
- Shut off power supply at fuse or circuit breaker!
- Use only the specified bulbs. Do not exceed the maximum wattage!
Assembly Instructions:
PREPARING FOR INSTALLATION
Carefully remove the new fixture from the carton as well as the yellow bag
that holds all of the parts. See the important notes above. Shut off power at
the circuit breaker and remove old fixture from wall, including the old
mounting strap. 1.
Take the mounting strap assembly from the parts bag. Mounting strap (A)
contains several threaded holes. Two set of mounting screws (C &D) should be
attached to mounting strap (A), remove these screws for later use. 2. Place
mounting strap (A) over the junction box and secure in place with mounting
screws (C). Tighten the screws securely with a screwdriver. Pull the house
wires through the center of the mounting strap (A).
ASSEMBLING THE FIXTURE
No Assembly Required – This item arrives assembled and ready for installation. Please proceed to the next step.
CONNECTING THE WIRES
Have an assistant support the fixture’s weight while completing the wiring. Refer to the wiring diagram and attach the fixture’s wires to the power supply wires from the junction box. Attach the fixture’s wires to the power supply wires from the junction box. Connect Hot to Hot (transparent wire with black inner thread, black, or smooth wire) Neutral to Neutral (transparent wire with white inner thread, white, or ribbed wire), and Ground to Ground (transparent wire with green inner thread, green wire, or copper). Twist the ends of the wire pairs together, and then twist on a wire connector. Make sure all twists are in the same direction. If there is no house ground wire coming from the junction box, locate ground screw (E) on the mounting bracket/mounting strap and wrap the fixture’s ground wire around the ground screw. Use a screwdriver to tighten the top of ground screw (E) onto the wires and into the mounting bracket/mounting strap. Tuck the wires into the junction box.
FINISHING THE INSTALLATION
Carefully attach glass shade (H) and metal shade (I) to the socket (G) in the order shown on the diagram. Secure glass shade (H) and metal shade (I) to the socket (G) using socket ring (J). Tighten socket ring (J) onto the threads of socket (G) until secure. 5. Lift the canopy (F) over mounting strap (A) and align side holes found on canopy (F) with the side holes found on the tabs of the mounting strap (A). Once aligned, secure canopy (F) to mounting strap (A) by threading small side screws (D) into the holes found on the canopy (F) and the tabs of the mounting strap (A). Thread small side screws (D) until secure. 6. Install a light bulb (not provided) into socket (G) in accordance with the fixture’s specifications. Do not exceed the maximum recommended wattage. Your installation is now complete. Turn on the power and test the fixture.
Get help, quick tips, and explore curated content
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>