CRYSTORAMA 1110-CH-CL-MWP Traditional Crystal 10 Light Crystal Chandelier Instruction Manual
- June 12, 2024
- CRYSTORAMA
Table of Contents
CRYSTORAMA 1110-CH-CL-MWP Traditional Crystal 10 Light Crystal Chandelier
Product Information
- This product is a lighting fixture manufactured by Crystorama. It is model number 1110-CH-CL-MWP.
- The fixture includes various crystal sets, such as square crystals, beads, rosettes, and balls, in different sizes.
- The electrical components of the fixture must be installed by a licensed electrician in accordance with the National Electric Code and local electrical codes.
- The fixture requires 10 Candelabra Base Bulbs with a recommended wattage of 40 Watts and a maximum wattage of 60 Watts. LED bulbs are recommended for extended use.
- The fixture is dry-rated, meaning it is suitable for indoor use only.
- Installation instructions are provided below.
Product Usage Instructions
- Place all the fixture parts on a soft cloth-covered platform before installation.
- Attach the bottom bowl, 2 metal washers, bottom bobeche, and metal washer in that order over the distributor box. Secure them with the finial.
- Attach the mounting bar to the outlet box.
- Determine the desired hanging height and adjust the chain to the correct length.
- Raise the fixture up and make the wire connections. Attach the canopy over the mounting bar and secure it with the collar ring.
- Dress the crystals as illustrated.
Note: Ensure that the power is turned off before performing any electrical connections or installations.
Warning: This product contains lead, which is known to the State of California to cause cancer and/or birth defects or reproductive harm. For more information, visit www.p65warnings.ca.gov.
WARNING: Electrical DangerTurn Power Off
All electrical components must beinstalled by a licensed electricianin
accordance with the NationalElectric Code and the appropriatelocal electrical
codes You will need 10- Candelabra Base Bulb40 Watts recommended 60 Watts
Max.USE LED BULBS FOR EXTENDED USE The fixture is Dry rated.
Dimension
HOW TO INSTALL
Place the fixture parts on a soft cloth-covered platform before installation of fixture.
- To install the 6″ & 12″arms, slightly loosen each screw on the metal plate. Pull a female plug through a hole in the upper metal plate.
- Connect the male plug at the end of the arms with the female plug that was just pulled.
- Push the end of the arm with the metal tab through the hole until stopped by the metal tab (this should also push the wires and plugs back inside the metal plate).
- Twist the metal tab counter-clock wise until both inserts lock onto the loose screws.
- Tighten the screw securing the arm in place. Repeat for all arms.
- Place the bottom bowl, 2 metal washers, bottom bobeche, metal washer in that order, over the distributor box. Secure with the finial.
- Attach the mounting bar onto the outlet box.
- Decide the desired hanging height and adjust the chain to the correct length.
- Raise the fixture up and do the wire connection. Attach the canopy over the mounting bar and secure with collar ring.
- Dress the crystals as illustrated.
Crystal Sets
- A. 4 Sets. (1)24mm
- B. 5 Sets. (5)14mm + (1)30mm + AS9-3″
- C. 15 Sets. (1)Square
- D. 5 Sets . (27)14mm
- E. 10 Sets. (17)14mm
- F. 10 Sets. (20)14mm
- G. 1 Piece. (7)14mm + (2)Rosette + (1)60mm ball
- H. 4 Sets. (3)14mm + AS9-3″
- I. 4 Sets. (5)14mm + AS9-3″
- J. 4 Sets. (1)14mm + (1)28mm + AS9-3″
- K. 5 Sets. (1)Ring of beads + (6)14mm + AS9-3″
- L. 5 Sets. (1)Ring of beads + (8)14mm + (1)30mm + AS9-4″
- M. 5 Sets. (1)Ring of beads + (1)30mm + AS9-4″
- N. 5 Sets. (1)28mm + AS9-3.5″
- O. 50 Sets. (1)14mm + AS9-2
- P. 5 Sets. (2)28mm + (1)24mm + AS9-4″
Part Number
- A. (2)-Wire Connector
- B. (1)-Mounting Bar
- C. (1)-Lock Washer
- D. (1)-Hex Nut
- E. (1)-Nipple
- F. (1)-Canopy (W5″xH1″)-XSN1110CHCAN5IN
- G. (1)-Collar Ring
- H. (1)-Collar Loop
- I. (1)-Chain (4mmx72″)-XSN1110CHCHA4MM
- J. (1)-Center Column Kit Loop
- K. (1)-Center Column Kit Top Bobeche ; Ø4″,4pin,24mm center hole.
- XSN1110CHBOB4IN
- Top Bowl ; Ø6″ ; 10pin,13mm center hole.
- XSN1110TODISH6IN
- Glass Vase; H8″
- Glass ball ; Ø5″
- Glass Vase ; H8″
- Metal Cover ; H1.5″
- L. (10)-PVC candle sleeve ; Ø7/8″, H4 1/8″.
- XSN1110CDL4IN
- M. (10)-Bobeche ; Ø5″ ; 5 pin, 24mm center hole.
- XSN1110CHBOB5IN
- N. (5)-6″ Arms with holder-XSN529CHARM6IN
- O. (5)-12″ Arms with holder-XSN500CHARM12IN
- P. (10)-Male Plug
- Q. (10)-Female Plug
- R. (1)-Distributor Box ; Ø5 1/2″
- S. (1)-Bottom Bowl ; Ø6″,8 pin,13mm center hole.
- XSN1110CHBODISH6IN
- T. (3)-Metal washer
- U. (1)-Bottom Bobeche; Ø4″,4 pin,24mm center hole.
- XSN1110CHBOB4PN
- V. (1)-Finial-XSN1110CHFIN
- Crystorama.com
Documents / Resources
|
CRYSTORAMA 1110-CH-CL-MWP Traditional Crystal 10 Light Crystal
Chandelier
[pdf] Instruction Manual
1110-CH-CL-MWP Traditional Crystal 10 Light Crystal Chandelier, 1110-CH-CL-
MWP, Traditional Crystal 10 Light Crystal Chandelier, Crystal 10 Light Crystal
Chandelier, 10 Light Crystal Chandelier, Crystal Chandelier, Chandelier
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>