EPIC FUTUREPROOF ES-K70 Digital Door Lock User Manual

EPIC FUTUREPROOF ES-K70 Digital Door Lock

FC

1. Rule Part 15.19(a)(3): This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
2. Rule Part 15.21: The users manual or instruction manual for an intentional or unintentional radiator shall caution the user that changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment

Safety Precautions

1. Please do not repair the product by yourself.
2. Please check the environment before installation.
3. Please read the manual carefully before using it.
4. Please change your pin number periodically.
5. Please do not knock or apply force on the lock.
6. Protect the product from wetness & moisture.
7. Please replace with new batteries all at once.
8. Clean the lock with a clean dry cloth.
9. Please use the product correspondingly.

Product Dimension

Product Description (Outer body)

Product Description (Inner body)

Pin Number Registration

Caution: Aways register pin number while door is open, default pin number upon purchase is [ 1,2,3, 4].
Warming!: Please do not forget the pin number at all times. Once forgotten you will not be able to register a new pin or card. There is no in- number reset.

1. To change the existing pin number
   • Open the battery cover.
   • Press the [ Registration ] button once
   • a beep sound will be heard
2. Enter the current pin number followed by a button. Press the number [ 1 ] button.
3. Enter a new pin number to be registered 4-12 digits.
   Press the (C] button on the number pad.
   A melody will be heard and the registration is complete.

Caution: Please register your pin number within 10 seconds after pressing the registration button or the registration process will be canceled. New registration of a single pin number will delete all previously registered pin numbers on the system.

RFID Card Registration (all-at-once)

A Caution New RFID cards are registered without erasing previous registration records. RFID cards included inside the bOX are not registered in detault. Only compatible cards can be registered and used.

1. Open the battery cover.
   Press the Registration J button once a beep sound will be heard.

2. Enter the current pin number, followed by a button.

3. Press the number [ 2] button.

4. Place the card to be registered on the card reader.
   The beep sound will be heard, and the saved 3-digit location number(001-100) will De displayed on the number pad.

5. Press the [Registration] button after all cards have been registered and the registration s complete.

Note:
Up to 100 RFID cards can be registered. To register multiple RFID cards, repeat step 4 before the number pad turns off. Place RFID cards on the card reader within 10 seconds after pressing the [Registration] button or the registration process will be canceled. No more RFID cards can be registered after the 100th registration.

RFID Card Registration (one-by-one)

Caution The card location number should be from 001-100 and it must consist of 3 digits always. When it is not individual card registration, the Pressing the []button will enable normal registration mode.

1. Open the battery cover. Press the [ Registration ] button once a beep sound will be heard.
2. Enter the current pin number, followed by the [button.
3. Press the number [ 2 ] button.
4. Enter the card location number consisting of 3 digits from (001-100), followed by the (button.
5. When the number pad arrow is displayed it is in RFID card entry standby status. Place the card to be registered on the card reader.The beep sound will be heard, and the saved 3 digit location number wil be displayed on the number pad.
6. To register additional RFID cards When all numbers on the pad is lighted, enter new location number, followed by [ button, then register the new card. When there are no additional cards to be registeredPress the [ Registration ] button to complete the registration.

RFID Card Deletion (all-at-once)

1. Open the battery cover.
   Press the [ Registration ] button once beep sound will be heard.
   Enter the current pin number followed by a []button.

2. Press number [8 ] button.

3. Long press the button for 5 seconds When the melody is heard, Al RFID cards are deleted.

RFID Card Deletion (one-by-one)

1. Open the battery cover.
   Press the [ Registration ] button once a beep sound will be heard.
   Enter the current pin number, followed by a button.

2. Press the number [ 8 ] button followed by the l(a)Jbutton.

3. Enter the registered card location number, followed by a button.

4. After the deletion is complete, all numbers are lighted on the number pad Additional card deletion is in standby mode.
   If there is no location number to be deleted, press the [ Registration] button.

Guest Pin Number Registration

1. Open the battery cover.
   Press the [ Registration ] button once a beep sound will be heard.

2. Enter the current pin number, followed by the [O]button.

3. Press the number [ 3 ] button.
   4 Enter the new guest pin number to be registered (4-12 digits and press the button to complete the registration.

• The guest pin number is 1 time entry only.
• New registration will delete old guest pin number.
• When registration mode is cancelled old pin number will be restored.

Dual-mode Security Feature Setting

The pin number & RFID card should be registered first before setting this feature.

1. Press the [Registration] button for 5 seconds the entire LED will light up after 3 seconds the alarm will stop and after 2 seconds it will be on again
2. Enter the current pin number. When you press the []button, the front panel LED will to blink and light up.
3. Press [ 1] button to Turn-Off Dual-Mode Security.
   Press[ 3] button to Turn-On Dual-Mode Security.
   During Dual-mode Security Setting. when the confirmation sound is heard, everything will be turned of.

Random Number Feature

Note Random number feature is enabled in default.
This is a security feature that keeps the pin number from being exposed by the additional random number that is added before or after the original pin number. The number to be entered incduding the pin number should not exceed 20 digits.

Opening Door Outside
Method 1:Opening by pin number

1. Touch the number pad.
2. Enter [ Pin number and press I DUtn.
3. After the melody is heard, the door will open.

Method 2: Opening by RFID card
During Automatic Detection Mode Press the registered RFID card on the reader. Melody will be heard and the door will open.
During Manual Detection Mode louch the number pad, check it then the number pad lights up, and place the registered RFID card on the reader. Melody will be heard and the door will open

Method 3: Opening by random number
Touch the number pad, enter any random number, Enter pin number, press [] button or enter pin number first, then enter any random number, then press (]button and the door will open.

• enter any random number + Enter pin number+[]button.
• Enter pin number+ Enter any random number + []button.
  Either way, when the melody is heard, The door will open.

Method 4: Opening by Dual-mode Security

• Enter Pin Number+
• Place the card to be registered on the card reader

Closing Door Outside

Method 1: Automatic lock mode
The door will lock automatically after 2 seconds of dosing the door. 2 Sec

Method 2: Manual lock mode
Touch the number pad and the door will lock.

**Opening Door Inside

**

Note Tun the handle downward within seconds of opening the do0r or the door will lock again.

By turning the handle downward
While the door is dosed turn the handle in a downward motion and the door will open.
Caution: Do not install on inside-puling doors,

Closing Door from Inside$

Method 1: Automatic lock mode
The door wil lock automatically after 2 seconds of dosing the door.

Method 2: Manual lock mode
After dosing Close ] button and the door will back on
Note anua mode, when the [ Manual Lock] button, is pressed, the -beep sound will be heard to signal that the door is locked,

Forced-Lock Feature

Inside double lock – When enabled will not allow Pin, Card, entry from outside.

Setting

1. After casing the door.
2. Press the [$afety button] located on the inner body for 3 seconds melody will be heard, and the setting Is complete.

Cancellation
Turn the inner body handle in downward motion inside, and the double lock setting will be canceled.

Automatic/ Manual Lock Setting
An optional feature that lets you set the lock-in automatic and manual lock mode.
Setting: While the door is partially opened

Note: Automatic Lock Mode is set in default. In Manual Lock Mode, the door wil not lock after dosing the door, instead touch the number pad outside or press the [ Open/ Close ] button inside to lock the door.

RFID Card Automatic / Manual Detection Setting

An optional feature that lets you set the RFID Card detection to automatic and manual mode.

Note :

1. In Automatic Mode, Place the RFID Card on the card reader and the door will open.
2. In Manual Mode, -Touch the number pad, Place the RFID Card on the card reader and the door will open. Automatic Mode is enabled in default.

Sound Mute Function

Regardless of the volume setting, This feature lets you mute the operation melody. This is per 1 time usage only. The operation sound will occur on next operation.

1. Touch the number pad, and press the [] button.(ln mute state)
2. Enter the Pin number, press the [ C] button, the door will open. (Number pad will blink)

Sound Volume Setting

This feature alows the user to adjust the operation sound volume per level. (perform while door is closed) Sound can be adjusted up to 7 levels.

Note

• Press the (3] button to increase the sound.
• Press the [6] button to decrease the sound.
• In mute mode, the number pad will blink when you press a number. The volume level is set on high in default.

Home Network Module & Remote Control Setting

This feature lets you open the door remotely via home network devices and remote control.(Optional)
Home Network Module and Remote Control setting procedure is the same.

Registration Note For registration of additional remote control repeat step number Up to 5 remote controls can be registered.

Mechanical Key

Note Opening the door when the lock is not functioning normally.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>